Land Pride grading scraper

[irvingj]

Thanks, jenkinsph-- I did go ahead and remove the pin connector and replaced it with an 1-7/8" ball connector (most of my stuff is that size). That should hold it even better for backing up. I plan to try it out on a neighbor's driveway soon- that should give it a good workout, theirs is a lot worse than mine.

wijmcinwi- welcome to TBN! I haven't yet had to replace my shearpin, but I was surprised to notice it's already been bent a bit. Still have the two spares that came with it....

It doesn't yet have a lot of use, but I'll admit it looks as though that pin will break easily --and most likely often! I might try to replace it with a "standard" grade two shearpin bolt from a local supplier; I've used those on my snowblower with no apparent ill effects. They're a lot less expensive.

 

[Machold]

Interesting thread because I have mixed feelings about my LP LGrader, probably because I haven't yet mastered its proper use.

One thing that helps is having a hydraulic top link on my B3030. I don't use the scarifiers because my 500 yard-long lane way has gravel over larger stones below. The larger stones if lying on top are murder on tires.

I should think the grader with scarifiers would be excellent for new road grading. Not so much for maintenance of existing gravel road.

As someone here posted, an instructional video on the use of the grader would be a big help.

 

[TripleR]

Interesting thread because I have mixed feelings about my LP LGrader, probably because I haven't yet mastered its proper use.

One thing that helps is having a hydraulic top link on my B3030. I don't use the scarifiers because my 500 yard-long lane way has gravel over larger stones below. The larger stones if lying on top are murder on tires.

I should think the grader with scarifiers would be excellent for new road grading. Not so much for maintenance of existing gravel road.

As someone here posted, an instructional video on the use of the grader would be a big help.

How To Video Demos - Implements & Attachments

 

[jenkinsph]

Interesting thread because I have mixed feelings about my LP LGrader, probably because I haven't yet mastered its proper use.

One thing that helps is having a hydraulic top link on my B3030. I don't use the scarifiers because my 500 yard-long lane way has gravel over larger stones below. The larger stones if lying on top are murder on tires.

I should think the grader with scarifiers would be excellent for new road grading. Not so much for maintenance of existing gravel road.

As someone here posted, an instructional video on the use of the grader would be a big help.

When the scarifiers are not needed simply raise them up. I know the next grader I build will have hydraulic scarifiers similar to my boxblade. My landplane/grader has straight blades without scarifiers and seems to do a good job for me. I also find the hydraulic top link is invaluable for this work as you need to adjust the trim to different settings when changing directions. I also experimented with the blades at different settings and have found that I get best results with them set flush with the bottom of the skids. This enables you to remove a slight mound while still dropping the extra material in the depressions.

Seat time and a little experimenting is all it takes to learn to use these implements.

 

[rkeith]

I have one that looks very similar made by Dirt Dog.
Dirt Dog

I paid $760 for mine and it works great! I just used it on my driveway that's about 75 years old and it looks brand new... nice and smooth!!!

I have the 60" version and pulled it with a MF1529 and with the scarifiers at full depth it was easy.

 

[TO_Bud]

Coming late to this discussion but I couldn't resist. As others have done on the forum I built my own road grader copying the design of the LP and other heavier graders. Was able to come by some used County Plow truck blades that were 7 feet wide. I placed the two blades on an angle and ended up 6.5' wide. Front blade .75 inch below the side skids and the back blade even. I've got a 40hp tractor with a hydraulic top link. The grader weighs 800 lbs. and I groom our 1/4 mile road of crushed limestone.
The road becomes hard as concrete in some areas after 6 months of travel on it by 10 homes and all their vehicles. I don't have scarifiers on it but I thought the 800 lbs would be plenty and it is for all parts except the really hard packed areas. I have added an additional 500 lbs to the sled for a total of 1300 lbs. Long story short is I grade it over and over again for about 4 hours to thoroughly cut through all the potholes and fluff and mix the stone with the fines. I finish with my rear blade to recreate the crown and then roll it with a water filled roller. The surface is beautiful when I am done and all the neighbors love it. We used to pay a contractor on a full size road grader $1000 for the service (took him a few hours as well). The home made grader does as good a job as he did so I can vouch for their effectiveness. Lastly, I tried to do the road before with my box blade with scarifiers and it was totally ineffective.
Bud

 

[RDrancher]

Dragging this great discussion on grading / scrapers back up.

I've been looking at Befco, Dirt Dog and Land Pride. Dirt Dogs closest dealer is out of state, and the only dealer for Befco in the DFW area is REAL proud of their product line. Land Pride has several dealers close, including my local Kubota dealer that will price match any deal that I can find.

So...

I thought that I had finally made a decision to go with the Land Pride model, but I am concerned about the post concerning the blade and shank wear. The main bulk of my business entails new gravel driveways / parking areas and restoration. I'd sure hate to be replacing blades every couple of months. I've been using a Bush Hog box blade for several years now with very little wear showing on the blade.

While I'm at it...are the Land Pride skids replaceable?

 

[jenkinsph]

RDrancher,

I wouldn't worry about the steel quality too much on a name brand product. As far as the blades are concerned if you need to change them there are a multitiude of companies that have good blades that you could use. When I built my landplane/grader I bought two good 8' blades 5/8"x6"x96" double edged and after two years of use I can't see much wear.

 

[PaleFX]

Well I have been following this topic for a bit and I have to say that it seems obvious these drag type graders are the tool of choice for driveway maintenance!

Here is a link for what appears to be a heavy duty model... I'm intrigued by the rear gate idea on these that allows for more precise control of the spread of material!
Domor Equipment | Hydraulic Adjustable Grader

Anyone have any experience with this manufacturer?

 

[KML]

Dragging this great discussion on grading / scrapers back up.

I've been looking at Befco, Dirt Dog and Land Pride. Dirt Dogs closest dealer is out of state, and the only dealer for Befco in the DFW area is REAL proud of their product line. Land Pride has several dealers close, including my local Kubota dealer that will price match any deal that I can find.

So...

I thought that I had finally made a decision to go with the Land Pride model, but I am concerned about the post concerning the blade and shank wear. The main bulk of my business entails new gravel driveways / parking areas and restoration. I'd sure hate to be replacing blades every couple of months. I've been using a Bush Hog box blade for several years now with very little wear showing on the blade.

While I'm at it...are the Land Pride skids replaceable?

I know there was at least one report of wear problems but my LandPride GS has a few hundred hours on it, mostly doing gravel roads and the wear parts are holding up very well. Yes, the skids are replaceable.