Results 1 to 5 of 5
  1. #1
    Bronze Member
    Join Date
    Dec 2006

    Default pto adapter on king kutter tiller 72in

    HI All,

    I recently purchased a kk 72 tiller, and it is my understanding that I need 6 inches of overlap on the pto shaft , I am 2 inches short so I purchased a pto adapter and now I am at 6 inches.

    My question is , does it matter what end of the pto shaft I put the adapter on ??

    Also, the tiller is not I-match compatiable so I took the I-match off and purchased Pats quick hitch system. are you suppose to use any bushings on the pins , or do you just connect the tiller onto the hitch using the pins that are on the tiller and then put a lynch pin to prevent it from moving.


    JD 4320

  2. #2
    Bronze Member
    Join Date
    Dec 2006

    Default Re: pto adapter on king kutter tiller 72in

    please reply

  3. #3
    Silver Member Rockin' G Ranch's Avatar
    Join Date
    Apr 2008
    Point Blank, TX
    Kubota L4740 HST with FEL

    Default Re: pto adapter on king kutter tiller 72in

    My understanding is that the PTO extension goes on the end that attaches to the tractor PTO.
    Pat's hitch should be attached to the tiller pins on the implement. I normally put a large washer over the pin (outside of the hitch) then install a lynch pin.

  4. #4
    New Member Linework's Avatar
    Join Date
    Nov 2008

    Default Re: pto adapter on king kutter tiller 72in

    I also have a 6' King Kutter Tiller and have had simular issues with the PTO shaft length, After talking at length with a King Kutter Rep, I opted to buy the correct length shaft. I have seen pto extensions fail and come apart due to poor workmanship, and did not want that issue. A new shaft, when measured right, will have more than the min overlap, and will be that much better under stress. Plus a better piece of mind !! I would guess that my new shaft has around 10" or 12" of overlap. I will say that I was very pleased with the help I recieved from the King Kutter Rep.
    L 3400 DT and other misc.

  5. #5
    Bronze Member
    Join Date
    Dec 2009
    So. Maryland
    JDeere LA,B,40,520,620,430,1010/Farmall superA,H/Kubota L39

    Default Re: pto adapter on king kutter tiller 72in

    I would have just left it 2" short & not worried about it. You still have 4" covering it.

Similar Threads

  1. Tiller 5 ft king kutter tiller price
    By mattellis2 in forum Attachments
    Replies: 4
    Last Post: 01-22-2013, 01:42 AM
  2. Tiller King Kutter Tiller Purchase
    By topshop in forum Attachments
    Replies: 10
    Last Post: 08-27-2008, 08:39 PM
  3. Tiller 5' King Kutter Tiller
    By dooleysm in forum Attachments
    Replies: 23
    Last Post: 08-08-2007, 11:34 PM
  4. Tiller king kutter tiller shaft -help needed!!
    By moosetracks in forum Attachments
    Replies: 5
    Last Post: 10-11-2004, 06:31 PM
  5. Tiller King Kutter Tiller
    By Alan L. in forum Attachments
    Replies: 7
    Last Post: 05-31-2001, 11:02 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
© 2018 TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.