Results 1 to 7 of 7
  1. #1
    Bronze Member
    Join Date
    Dec 2002
    Posts
    73
    Location
    N.Y.
    Tractor
    JD 4400 w/R-1 & R-3

    Default 2 bottom plow i.d.

    found 2 bottom plow with label on mold board heavy duty,super chief, X series. It is a 16", 3ph. I think each plow would trip. It is not like the wheeled units where you can see the springs and they have the levers for adjustment. It has coulters,but no tail wheel. Can see where there was a tag on rightside of frame going to the center link, that may have showed the trip, and reset but no other info.Tag on mold board may be from replaceded mold boards. My guess is a Ford product. What do you folks think?

  2. #2
    Bronze Member
    Join Date
    Dec 2002
    Posts
    73
    Location
    N.Y.
    Tractor
    JD 4400 w/R-1 & R-3

    Default Re: 2 bottom plow i.d.

    Found old papers. Super chief was used by International but I have no other info yet.

  3. #3

    Join Date
    Jul 2002
    Posts
    404
    Location
    garland county arkansas
    Tractor
    Kubota L3000DT

    Default Re: 2 bottom plow i.d.

    Give john miller just a little time and he'll produce a picture!
    might even tell you the date it was built. [img]/forums/images/graemlins/grin.gif[/img]

  4. #4

    Default Re: 2 bottom plow i.d.

    Hello tractorhal--The Super Chief is indeed a IH product and has a unusual 2 piece point/share setup--very expensive to maintain and find parts for--Ken Sweet
    Sweet Farm Equipment Co.

  5. #5

    Join Date
    Jan 2001
    Posts
    2,518
    Location
    Capital District, Upstate New York
    Tractor
    Satoh S650G, MF135, MF165, JD5205

    Default Re: 2 bottom plow i.d.

    <font color="blue"> Give john miller just a little time ... </font>

    I sure appreciate the vote of confidence... [img]/forums/images/graemlins/smile.gif[/img]

    but... plow ID is not my forte'... as I have a 3 bottom of my own, I can't positively ID... [img]/forums/images/graemlins/blush.gif[/img]

  6. #6
    Bronze Member
    Join Date
    Dec 2002
    Posts
    73
    Location
    N.Y.
    Tractor
    JD 4400 w/R-1 & R-3

    Default Re: 2 bottom plow i.d.

    Ken, The shares appear to be one piece,with 4 bolts holding it on . The shins are one piece, two bolts. Haven't done any disassembly yet. Is there any chance of getting parts breakdown, and operating instructions? How do you measure the plows to determine if they are 14" or 16"? Other than some rust the unit looks to be in fair condition. Did each plow trip on this unit? The wear plates,furrow side look in good shape. Thanks.

  7. #7

    Default Re: 2 bottom plow i.d.

    Hello tractorhal--To determine 12-14-16 inch--Measure from the inside of one main beam to the outside of the other main beam--Points may have been changed over--the original usually had a point that had a replacable tip that was removable from the backside of the point--These plows were trip protected--Cant help on the manual--maybe a Ebay search could come up with one?--Ken Sweet
    Sweet Farm Equipment Co.--Hay Harvesting Specialists

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
© 2014 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.