dex3361
Elite Member
- Joined
- Aug 22, 2008
- Messages
- 3,568
- Location
- N. of Charleston WV
- Tractor
- Kubota L4400-1 HST,FEL, 3x3 remotes, TNT. BX1500 54 mmm
It is oriented nearer the bottom. Just like in the manual.
Voltmaster PTO generator
- Thread starter bubbacuse77
- Start date
sdkubota
Platinum Member
Thanks, I'll flip mine around after I weld the new plug onto the plate.
OP
bubbacuse77
Platinum Member
What did people do before TBN to solve these problems?
Soundguy
Old Timer
- Joined
- Mar 11, 2002
- Messages
- 52,238
- Location
- Central florida
- Tractor
- RK 55HC,ym1700, NH7610S, Ford 8N, 2N, NAA, 660, 850 x2, 541, 950, 941D, 951, 2000, 3000, 4000, 4600, 5000, 740, IH 'C' 'H', CUB, John Deere 'B', allis 'G', case VAC
pretty common to have the oil check sump level on that type of gearbox BELOW the input shaft seal.
as the gear spins it will distribute oil..e tc..
as the gear spins it will distribute oil..e tc..
Soundguy
Old Timer
- Joined
- Mar 11, 2002
- Messages
- 52,238
- Location
- Central florida
- Tractor
- RK 55HC,ym1700, NH7610S, Ford 8N, 2N, NAA, 660, 850 x2, 541, 950, 941D, 951, 2000, 3000, 4000, 4600, 5000, 740, IH 'C' 'H', CUB, John Deere 'B', allis 'G', case VAC
pretty common to have the oil check sump level on that type of gearbox BELOW the input shaft seal.
as the gear spins it will distribute oil..e tc..
as the gear spins it will distribute oil..e tc..
sdkubota
Platinum Member
Regarding the wiring that comes off of the brushes at the end of the shaft...
Could those possible be associated with the 12V DC, 8.3A outlet located on the outlet panel? Just an after thought. Sorry to beat this dead horse.
sdkubota
Platinum Member
Not only did they tap the threads at an angle and nearly strip them...they placed the plate upside down! Those Chinese slave labor kids...
Soundguy
Old Timer
- Joined
- Mar 11, 2002
- Messages
- 52,238
- Location
- Central florida
- Tractor
- RK 55HC,ym1700, NH7610S, Ford 8N, 2N, NAA, 660, 850 x2, 541, 950, 941D, 951, 2000, 3000, 4000, 4600, 5000, 740, IH 'C' 'H', CUB, John Deere 'B', allis 'G', case VAC
someone must have missed their 1 bowl of rice a day / 10 cent paycheck that week to have messed up like that....
dex3361
Elite Member
- Joined
- Aug 22, 2008
- Messages
- 3,568
- Location
- N. of Charleston WV
- Tractor
- Kubota L4400-1 HST,FEL, 3x3 remotes, TNT. BX1500 54 mmm
The wires to the brushes are to provide exitation voltage to the rotor coil and the voltage comes from the AVR (Automatic Voltage Regulator).
Last edited:
p0opstlnksal0t
Silver Member
How do these voltmaster generators stack up against the winco units? Are they made in america? I'm hoping to stay away from a Chinese made unit