Results 1 to 2 of 2
  1. #1
    New Member
    Join Date
    Jan 2013
    Posts
    10
    Location
    la
    Tractor
    john deere 2440

    Default taylorway disc

    I need to know how get the disc pans off. how to seperate the axle housing- dish pan spacers. thanks for any help you can give me.

  2. #2
    Super Member Gary Fowler's Avatar
    Join Date
    Jun 2008
    Posts
    7,255
    Location
    Bismarck Arkansas
    Tractor
    2009 Kubota RTV 900, 2009 Kubota B26 TLB & 2010 model LS P7010

    Default Re: taylorway disc

    I find that the easiest way is to, first loosen the axle nut but leave it loosely on the axle, unbolt the bearing carriers, roll the gang out from under the disc frame, then stand it up on end. Then you can lift each piece of the assembly off. You apparently aren't familiar with disc repair so don't mix up the order that you remove the spools and back plates. Also note that the spools (spacers between the blades) have a concave side and a convex side so they fit the contour of the blades so they need to go back in that orientation.
    What exactly are you trying to do, replace a broken disc blade?
    When putting it back together, tighten the nut using a wrench and hammer (I use a pipe wrench so I can beat it severely with a hammer). When you have it as tight as you can get it, then hit each blade with your hammer. DONT TAP it, HIT it hard to settle them in to the spacers, then tighten the nut some more. Repeat until you aren't able to tighten the axle nut any more. Then go disc with it for a few minutes and then try to tighten it again. After you are assured that it is tight, then you can bend the tab over on the nut to hold it in place.

    PS. If you are replacing a blade that is before the first bearing carrier, then you don't need to remove the gangs, just take off the axle nut by straightening the locking tab and remove what you need to get to the broken blade, put on new blade and put everything back in the order and orientation that you removed it and follow the tightening sequence described above.
    2010 LS P-7010C 20F/20R gear tractor & FEL, 2009 Kubota B 26 TLB, RTV 900 Kubota,17 foot Lund boat with 70HP motor, 2012-20 ft 12k GVW trailer, 2011- 52" Craftsman ZTR mower, 2013 Ferris Zero Turn, 3 weed whackers, pressure washer, leaf blowers, 7 foot bush hog, 8 foot landscape rake , 8 foot 3 PH disc, 2 row cultivator, 350 amp Miller AC/DC welding machine and all the tools needed to keep them all repaired and running.

Similar Threads

  1. Taylorway T245 5ft rotary mower
    By kebo in forum Attachments
    Replies: 0
    Last Post: 11-16-2008, 03:42 PM
  2. Farmpro 48 disc v.s. Agri-fab single row disc
    By BTackett in forum Attachments
    Replies: 4
    Last Post: 03-10-2008, 11:17 PM
  3. TaylorWay box blades
    By LabLuvR in forum Attachments
    Replies: 0
    Last Post: 03-16-2006, 11:40 AM
  4. Replies: 6
    Last Post: 05-17-2005, 12:49 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
© 2014 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.