Re: Help: ACS Error on Bobcat Skid Steer
Hi,
I am brand new to this forum but you guys are discussing my exact problem and I was wondering if you had any thoughts on my specific case.
I purchased a 2003 T200 with 2500 hrs and dual controls on it a few weeks back. When I purchased it (private sale) the arms would lift but the bucket wouldn稚 tilt. As soon as I would try to tilt the bucket the ACS light would come on and neither would work.
The machine was just covered in Georgia Clay and mud so I broke out the pressure washer and three hours later finally had it cleaned up. To my delight when I started it both actuators worked and I looked back with gratitude that my mother had forced me to use soap and value cleanliness... Unfortunately it only lasted five minutes. Now as soon as I start the machine I get the three beeps and the ACS light comes on locking both actuators.
I have spent the last couple weeks tracing wires and cleaning contacts. I have found three ground problems and fixed them but with no result. Unfortunately all the obscenities that I can think of have also had no effect...
I finally took it to the bobcat dealership and they charged me 85 dollars to push in the light switch and give me the code... (32-34) they also said that they switched the wiring to test the controls with no change. They informed me that they had no idea what the problem actually was but they would be happy to start changing out parts (1000.00 each) until it revealed itself... I loaded the machine back on the trailer and it is now safely stowed back in my garage.
I have tried the battery disconnect reset and the reset by using the release on the hand controls and holding them together while turning on the key all to no avail. I am just about to purchase new actuators and just bite the bullet unless you have any idea what else it could be.
I would speculate that it has to be the actuators accept that when I had gotten the thing wet both worked. Do you fellas have any idea where I could go next? I would greatly appreciate any help. Thanks. JB DeVore.
Re: Help: ACS Error on Bobcat Skid Steer
If the error code is consitantly the tilt actuator, then unplug both actuators and plug the tilt harness into the lift and lift into tilt then try it again. If code changes to lift actuator error the tilt actuator is failed or tilt spool is stuck out of neutral. If code does not chage then problem is in wire harness to controller or in controller. More than likely it is an actuator. Buying and installing new actuators yourself will not work unless the dealer upgraded the software when he was checking it. Software must be version 56 or higher for the new actuators to calibrate correctly. Turn key on then push and hold the bucket positioning button until the hourmeter displays the software version number to check.
Lift acutator is the bottom one, tilt is on top of it.
Re: Help: ACS Error on Bobcat Skid Steer
Quote:
Originally Posted by
SSdoxie
If the error code is consitantly the tilt actuator, then unplug both actuators and plug the tilt harness into the lift and lift into tilt then try it again. If code changes to lift actuator error the tilt actuator is failed or tilt spool is stuck out of neutral. If code does not chage then problem is in wire harness to controller or in controller. More than likely it is an actuator. Buying and installing new actuators yourself will not work unless the dealer upgraded the software when he was checking it. Software must be version 56 or higher for the new actuators to calibrate correctly. Turn key on then push and hold the bucket positioning button until the hourmeter displays the software version number to check.
Lift acutator is the bottom one, tilt is on top of it.
Thank you I will check that out in the morning. It turns out that Bobcat also has a service directive that may also fix this problem. I called bobcat directly because I was dissatisfied with the service at my local dealer. I asked them to check and see if there was a service directive or recall for this machine and sure enough there was. They are sending a tech out to my home Wednesday for free to fix it. If anyone has this problem check with your regional rep or local service dealer to see if your machine might also be eligible.
Thanks again.
JB
