Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 23
  1. #11
    Platinum Member
    Join Date
    Dec 2006
    Posts
    710
    Location
    Coastal Rhode Island
    Tractor
    Jinma 354, purchased 2007

    Default Re: Pole puller

    If you're going to install a pivot anyway cut it off flush with the ground.

  2. #12
    Bronze Member
    Join Date
    Sep 2010
    Posts
    91
    Location
    Central NYS
    Tractor
    Kubota B9200

    Default Re: Pole puller

    Very good ideas but at 73 I think I like the bolt the best. I can drill a hole but do ladders....not so much

  3. #13
    Platinum Member
    Join Date
    Nov 2012
    Posts
    889
    Location
    mansfield,Il
    Tractor
    john deere

    Default Re: Pole puller

    So , you are going to drill ahole near the bottom insert a bolt and heave-ho . Where is this 24 foot pole going to land ?

  4. #14
    Bronze Member
    Join Date
    Sep 2010
    Posts
    91
    Location
    Central NYS
    Tractor
    Kubota B9200

    Default Re: Pole puller

    Damned if I know.
    Quote Originally Posted by kevin37b View Post
    So , you are going to drill a hole near the bottom insert a bolt and heave-ho . Where is this 24 foot pole going to land ?

  5. #15
    Platinum Member
    Join Date
    Nov 2012
    Posts
    889
    Location
    mansfield,Il
    Tractor
    john deere

    Default Re: Pole puller

    Make sure the old dog and the old woman are out of range .

  6. #16
    Elite Member
    Join Date
    Jul 2009
    Posts
    4,467
    Location
    SW WA
    Tractor
    Kubota BX2360

    Default Re: Pole puller

    Some hinges:

    -68646_2-jpg

    -tiltb_sk-gif

    -2335347392_56e6388b99_z-jpg

    -f-af-w-hinged-base

    -cpfghb33ih_-04_base-open_33ft-high-pressure

    -tiltb-jpg

  7. #17
    Elite Member
    Join Date
    Jul 2009
    Posts
    4,467
    Location
    SW WA
    Tractor
    Kubota BX2360

    Default Re: Pole puller

    Make a hinge before lowering it.



    Mark the pole about 2 feet high.

    Bolt a 4 foot channel on each side. Two bolts above the mark, two below.

    Cut the pole at the mark, with a wide gap so the end can pivot.

    Remove one of the bolts and lower the pole.

    Bruce

  8. #18
    Bronze Member
    Join Date
    Nov 2009
    Posts
    90
    Location
    Devon UK
    Tractor
    Iseki 2160f

    Default Re: Pole puller

    If it was me i would fab a hinge and weld it on then prop the pole and cut it you can then lower it and do the repair

    Then weld a flange on the other side so you can raise it back up and bolt it back together

  9. #19
    Silver Member SHORT KID's Avatar
    Join Date
    Feb 2010
    Posts
    169
    Location
    Poconos, PA
    Tractor
    Mahindra 2615 hst fel, bh

    Default Re: Pole puller

    I think I would just stand my ext. ladder straight up against the pole and tie it off at the bottom adn up as high as I could reach. Then I would fut my FEL up against the other side of it for support, climb the ladder and tie off to the bucket. Take a safety belt and tool bag up with you and climb the rest of the way to make the repair. Be Careful.

  10. #20
    Veteran Member
    Join Date
    Feb 2012
    Posts
    1,233
    Location
    Northern Michigan
    Tractor
    KIOTI DK50 HST

    Default Re: Pole puller

    Rent a man lift and change it out. $150 and 2 hours and nobody gets hurt. CJ
    Kioti DK50HST Cab
    401 FEL
    Saws, 338xp,346xp mod,372xp mod, 390xp, Stihl combi 130 trimmer.

Page 2 of 3 FirstFirst 123 LastLast

Similar Threads

  1. Tree puller
    By melanelly in forum Build-It Yourself
    Replies: 11
    Last Post: 02-19-2012, 05:43 AM
  2. best rock puller?
    By Groo in forum Construction Equipment
    Replies: 3
    Last Post: 07-11-2010, 07:50 PM
  3. Log puller
    By Egon in forum Related Topics
    Replies: 18
    Last Post: 05-02-2009, 03:19 PM
  4. Help with sapling puller?
    By TMcD_in_MI in forum Build-It Yourself
    Replies: 42
    Last Post: 01-01-2007, 01:04 AM
  5. 3 pt pipe puller??
    By JohnnyD in forum Attachments
    Replies: 3
    Last Post: 06-07-2002, 08:20 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
© 2014 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.