Results 1 to 6 of 6
  1. #1
    Bronze Member
    Join Date
    Oct 2005
    Posts
    69
    Location
    Eatonville, WA
    Tractor
    JD 3520

    Default 300CX FEL Quick Attach dimensions?

    Does anyone know where I can get the dimensions for the JD quick attach hooks and pins? I'm building a root grapple and need to configure the attach points. I have the hooks and pins and can measure my loader, but was hoping for some more accurate numbers.

    Thanks

    JBA

  2. #2
    Super Star Member kennyd's Avatar
    Join Date
    Jul 2003
    Posts
    11,470
    Location
    Westminster, MD
    Tractor
    John Deere 4110

    Default Re: 300CX FEL Quick Attach dimensions?

    I don't have the numbers...
    But when I built my forklift set and my FEL snowplow I just mounted the peices to the loader with clamps and tacked it together as I built the frame. Seemed much easier and safer than trying to measure. I have not seen the dimensions published.
    John Deere 4110HST
    FEL, MMM, Artillian 42" Forks, I-Match, Ballast Box, #380 plow (modified to fit), Markham LD-48 Grapple, Trac-Vac 854 and lots of other STUFF.

    John Deere 4x2 Turf Gator

    View some of my projects/adventures in my Picasa Album

    Simple JDParts Tutorial HERE

  3. #3
    Bronze Member
    Join Date
    Oct 2005
    Posts
    69
    Location
    Eatonville, WA
    Tractor
    JD 3520

    Default Re: 300CX FEL Quick Attach dimensions?

    Yeah, I guess that's what I'll do. I was just hoping that I could avoid the pain of hefting this thing around too much.

    Thanks Kennyd

  4. #4
    Veteran Member foggy1111's Avatar
    Join Date
    Dec 2008
    Posts
    2,486
    Location
    Nisswa, MN
    Tractor
    JD 3320 eHydro w/ 300CX Loader

    Default Re: 300CX FEL Quick Attach dimensions?

    Resurecting an old thread. Anyone got these JD dimensions??
    Last edited by foggy1111; 07-10-2011 at 10:05 PM. Reason: typo
    3320 eHydro, 300CX Loader & 15 + great attachments

    You gotta mine allot of dirt to find a diamond.

  5. #5
    Veteran Member foggy1111's Avatar
    Join Date
    Dec 2008
    Posts
    2,486
    Location
    Nisswa, MN
    Tractor
    JD 3320 eHydro w/ 300CX Loader

    Default Re: 300CX FEL Quick Attach dimensions?

    OK....so after lots more searching I found some dimensions that were posted for a JD QA "shrub bucket". I cut and pasted the dimensions below in case anyone else is building a gadget for a JD loader. I believe these are the same dimensions for a 300 loader.

    This would be allot easier if my tractor was close-by or if I knew of another similar tractor to measure stuff. Anyway.....here are the dims:


    Re: Shrub Bucket

    --------------------------------------------------------------------------------

    OK, here's what I measured:

    Bottom pins center to center = 46.75"
    Top brackets center to center = 40.25"
    Bottom pin center line to highest point on underside of top bracket = 15"

    I don't know what the official dimensions are for a 430/460 loader attachment, but these work for me. There is a wee bit of slop, especially in the top brackets, so these measurements are probably not exactly to spec, but they should work OK.

    btw. I'm almost done my next project - just needs painting. Stay tuned to this forum for my home made rear blade ....
    3320 eHydro, 300CX Loader & 15 + great attachments

    You gotta mine allot of dirt to find a diamond.

  6. #6
    New Member
    Join Date
    Oct 2011
    Posts
    1
    Location
    Choudrant, LA, Jackson Parrish
    Tractor
    JD 990

    Default Re: 300CX FEL Quick Attach dimensions?

    Foggy, Just found this site and joined. Need makes one come out and acknowledge his ignorance. I'm ignorant! I have a 300 cx attached to a JD 990. the left side popped free from the large still pivot point this morning, and I have tried pushing it back on at a large tree. All I accomplished was to scar my tree. I tried a sledge hammer, just marred the paint. Any suggestions?
    ronflurry

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
© 2013 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.