Page 1 of 2 12 LastLast
Results 1 to 10 of 17
  1. #1
    New Member
    Join Date
    Nov 2010
    Posts
    20
    Tractor
    Ford 961

    Default IH 574 drawbar question.

    Does anyone know the dimensions of the drawbar for a 574 IH tractor. I'm pretty sure the pivot pin is .950 other than that I don't know any other dimensions length, thickness, or width? My 574 has no drawbar and I'm trying to locate one for it. Thanks

  2. #2
    Advertiser sweettractors's Avatar
    Join Date
    Jul 2003
    Posts
    7,205
    Location
    Central Kentucky
    Tractor
    JD 6403 CHA-JD 3130 CHA

    Default Re: IH 574 drawbar question.

    I have them new for $160 + shipping. Ken Sweet
    http://www.sweetfarms.com/

    Sweet Farm Equipment LLC (Internet Sales, Shipping All States)
    Shipping Facility
    1815 Defries Rd., Canmer, Ky 42722 Toll Free 1-866-528-3323
    Ken Sweet sweet@scrtc.com

    Shipping Example: Can ship 800 lbs from Ky. to Dallas for $165
    The Northeast shipping corridor is a little more expensive.

  3. #3
    New Member
    Join Date
    Nov 2010
    Posts
    20
    Tractor
    Ford 961

    Default Re: IH 574 drawbar question.

    Thanks Ken
    I was hoping to pick up a used one. That is why I need the dimensions.
    If I can't find used one I'll consider new. I have a feeling the shipping would kill me on a new one from Kentucky.
    Stan

  4. #4
    Advertiser sweettractors's Avatar
    Join Date
    Jul 2003
    Posts
    7,205
    Location
    Central Kentucky
    Tractor
    JD 6403 CHA-JD 3130 CHA

    Default Re: IH 574 drawbar question.

    Quote Originally Posted by Stanley75 View Post
    Thanks Ken
    I was hoping to pick up a used one. That is why I need the dimensions.
    If I can't find used one I'll consider new. I have a feeling the shipping would kill me on a new one from Kentucky.
    Stan
    Well, We would drop ship from the closest warehouse to you and not KY. Ken Sweet
    http://www.sweetfarms.com/

    Sweet Farm Equipment LLC (Internet Sales, Shipping All States)
    Shipping Facility
    1815 Defries Rd., Canmer, Ky 42722 Toll Free 1-866-528-3323
    Ken Sweet sweet@scrtc.com

    Shipping Example: Can ship 800 lbs from Ky. to Dallas for $165
    The Northeast shipping corridor is a little more expensive.

  5. #5
    New Member
    Join Date
    Nov 2010
    Posts
    20
    Tractor
    Ford 961

    Default Re: IH 574 drawbar question.

    ttt....

  6. #6
    Platinum Member
    Join Date
    Jun 2000
    Posts
    585
    Location
    Central Mississippi, USA
    Tractor
    Case-International 385, Kubota L5450 w/LA1150A loader

    Default Re: IH 574 drawbar question.

    I have a Case IH 385, I think it's the same frame as yours. I took my draw bar off and put it up somewhere and can't put my hand on it right now. If I can find it I'll measure the pivot hole and get dimensions.

  7. #7
    Gold Member Avondale's Avatar
    Join Date
    Sep 2008
    Posts
    327
    Location
    Apple Hill, Ont
    Tractor
    Kioti DK 35; IH 574, Ranger 700 XP, Arctic Cat 500 TRV, Arctic Cat 400 FIS, Kawasaki 250 Bayou, Yamaha 200 BW.

    Default Re: IH 574 drawbar question.

    I have a 574 out back. I am unsure about the term drawbar. If you mean the one that runs across the lower arms of the 3 pt hitch or the bar that acts like a trailer hitch, (runs front/back)? My machine has both so I will try to remove the "hitch" type and check all dimensions. Please note, it has never been off to my knowledge so could take a bit. The other drawbar was purchased at TSC and is fairly common.
    "Life is tough. It's tougher when you are stupid". John Wayne

  8. #8
    Super Member RickB's Avatar
    Join Date
    Sep 2000
    Posts
    7,582
    Location
    Eastern NY
    Tractor
    Case 885, Ford 4000

    Default Re: IH 574 drawbar question.

    Not too hard to figure it out. Measure the anchor pin, that will give you the diameter of the front hole. The rear hole should be 1-1/8" or 1-1/4". Measure the clearance between the straps on the rear support, that is the maximum thickness. Width is measured between two bolts or pins dropped through the adjusting holes in the straps of the rear support. Rear hole needs to be centered exactly 16" behind the end of the 540 RPM PTO output shaft.
    We have too much gun control.
    What we need is more idiot control.

  9. #9
    New Member
    Join Date
    Nov 2010
    Posts
    20
    Tractor
    Ford 961

    Default Re: IH 574 drawbar question.

    Quote Originally Posted by Avondale View Post
    I have a 574 out back. I am unsure about the term drawbar. If you mean the one that runs across the lower arms of the 3 pt hitch or the bar that acts like a trailer hitch, (runs front/back)? My machine has both so I will try to remove the "hitch" type and check all dimensions. Please note, it has never been off to my knowledge so could take a bit. The other drawbar was purchased at TSC and is fairly common.
    I was referring to the bar hitch. Takes a 9/16 wrench to get it off on the underneath side of the transmission. I have the 3 point stuff just no drawbar.
    Thanks
    Stan

  10. #10
    New Member
    Join Date
    Nov 2010
    Posts
    20
    Tractor
    Ford 961

    Default Re: IH 574 drawbar question.

    Quote Originally Posted by RickB View Post
    Not too hard to figure it out. Measure the anchor pin, that will give you the diameter of the front hole. The rear hole should be 1-1/8" or 1-1/4". Measure the clearance between the straps on the rear support, that is the maximum thickness. Width is measured between two bolts or pins dropped through the adjusting holes in the straps of the rear support. Rear hole needs to be centered exactly 16" behind the end of the 540 RPM PTO output shaft.
    I have no anchor pin. I have no straps to hold the bar down. I do have the swing bar pin bracket off and the hole measures .950. That tells me the rear bar hole could be less than an inch. If I have to drill a hole I need to know what size? the 16 inches does help me out, for bar length though. The rear hole size isn't a concern.
    Thanks
    Stan

Page 1 of 2 12 LastLast

Similar Threads

  1. 4710 - Drawbar Question
    By timb in forum John Deere Owning/Operating
    Replies: 9
    Last Post: 03-21-2011, 07:17 PM
  2. Hello new and a question about a IH 3414
    By mike roma in forum Owning/Operating
    Replies: 5
    Last Post: 06-11-2009, 11:48 PM
  3. Question about drawbar hitch
    By /pine in forum Owning/Operating
    Replies: 6
    Last Post: 04-17-2009, 08:08 PM
  4. IH 1486 question
    By showcattle in forum Ag Tractors & Machinery
    Replies: 11
    Last Post: 03-26-2007, 03:26 PM
  5. Drawbar question
    By Harvster in forum Kubota Owning/Operating
    Replies: 16
    Last Post: 02-16-2007, 05:30 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
© 2014 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.