Results 1 to 8 of 8
  1. #1
    Veteran Member lhfarm's Avatar
    Join Date
    May 2002
    Posts
    1,223
    Location
    Central Indiana
    Tractor
    NH TC40DA

    Default Pricing hydraulic pump for IH C - best source?

    I restore old Willys jeeps and have a 3pt hitch on the back that uses the same pump as the IH model C. I need to replace the pump. Searching the Web, I've found prices from $425 to $700. Am I looking at different pumps or are IH parts being marked up that much? If I have to spend that kind of money, I'd like to be sure I'm working with a good operation. Would appreciate advice on good, fair priced sources.

    Thanks,
    Barry
    Lawson Hill Farm
    NH TC40DA
    '64 IH Cub Lo-Boy
    '47 Willys Jeep CJ2a w/ PTO
    '49 Willys Jeep CJ3a w/ PTO & 3pt lift
    http://www.farmjeep.com/

  2. #2
    Veteran Member
    Join Date
    Jan 2009
    Posts
    2,141
    Location
    Carroll, Ohio
    Tractor
    Massey 180 Diesel

    Default Re: Pricing hydraulic pump for IH C - best source?

    Is the pump beyond putting new seal/o-rings/sealing ring in? You can get seal/o-ring kits from Case/IH for a lot less than a new/rebuilt pump. Around $70-$75 for those kits.

  3. #3
    Veteran Member lhfarm's Avatar
    Join Date
    May 2002
    Posts
    1,223
    Location
    Central Indiana
    Tractor
    NH TC40DA

    Default Re: Pricing hydraulic pump for IH C - best source?

    Quote Originally Posted by DJ54 View Post
    Is the pump beyond putting new seal/o-rings/sealing ring in? You can get seal/o-ring kits from Case/IH for a lot less than a new/rebuilt pump. Around $70-$75 for those kits.
    I took the first pump we had for our jeep's Newgren 3pt lift to a hydraulic repair shop and they told me the pump was completely worn out and couldn't be repaired. Some research turned up the fact that the pump used by Newgren was the same one used on the IH-C. So I purchased a used C pump. The pump does work, but I'm not sure it isn't worn (gears) too and it certainly leaks. I have been searching the web for both rebuild parts (gears and seals/o-rings) and for new/rebuilt pumps.

    I guess I should take the pump to an IH dealer (nearest one is about 30 minutes away) and see if they can get the kits. I've not found the seals on-line, but have seen the gears.

    Thanks for the reply.
    Barry
    Lawson Hill Farm
    NH TC40DA
    '64 IH Cub Lo-Boy
    '47 Willys Jeep CJ2a w/ PTO
    '49 Willys Jeep CJ3a w/ PTO & 3pt lift
    http://www.farmjeep.com/

  4. #4
    Veteran Member
    Join Date
    Jan 2009
    Posts
    2,141
    Location
    Carroll, Ohio
    Tractor
    Massey 180 Diesel

    Default Re: Pricing hydraulic pump for IH C - best source?

    Most generally if it is leaking, it is the front seal, behind the drive gear. I've replaced the one's on both of my Super C's. Here is a link to Case/IH showing the pumps. Apparently they don't handle the gears etc. but do still carry new pumps. Rather pricey @ $733. Hoping mine last forever..!!

    Here is the link showing pumps & parts available + prices: (FARMALL C) - TRACTOR (1/48-12/51) Click on Hydraulics, then select pump from menu to see the pumps.

  5. #5
    Veteran Member lhfarm's Avatar
    Join Date
    May 2002
    Posts
    1,223
    Location
    Central Indiana
    Tractor
    NH TC40DA

    Default Re: Pricing hydraulic pump for IH C - best source?

    Thanks. I'll order a seal. Any tips on taking the pump apart and replacing the seal? I don't have a press. Should I take it to a shop?

    If all else fails, I might go with this - Farmall C Hydraulic Pump (384506R94)
    Barry
    Lawson Hill Farm
    NH TC40DA
    '64 IH Cub Lo-Boy
    '47 Willys Jeep CJ2a w/ PTO
    '49 Willys Jeep CJ3a w/ PTO & 3pt lift
    http://www.farmjeep.com/

  6. #6
    Silver Member koamfps's Avatar
    Join Date
    Jan 2012
    Posts
    179
    Location
    Michigan
    Tractor
    NH TN70DA & NH 2120

    Default Re: Pricing hydraulic pump for IH C - best source?

    Messicks.com should get you what you need

  7. #7
    Veteran Member
    Join Date
    Jan 2009
    Posts
    2,141
    Location
    Carroll, Ohio
    Tractor
    Massey 180 Diesel

    Default Re: Pricing hydraulic pump for IH C - best source?

    The pumps are pretty simple to take apart. Remove the drive gear, then the woodruff key. Mark the pump body and cover so the are reassembled in the same position. Remove bolts holding it together, and the usually come apart pretty easy. Might be an idea to mark the drive & driven gear so they go back together in the same mesh too. Just watch the little spring plate inside when putting it back together.

    I find a piece of clean scrap 2X6 to lay the pump segmnent on, to tap the new seal in. A bushing/seal driver, or a clean piece of 1X or 2X2 wooden block, once the seal is started to take it on home.

    Lube everything with your hydraulic oil, and put back together. Just be careful putting the shaft back through the new seal. Some lube, and I like to give it a little twisting action as I push it through nice & easy.

    The link I posted is actually from Messick's. Saves some sticker shock sometimes...

  8. #8
    New Member
    Join Date
    Nov 2013
    Posts
    2
    Location
    prentice, WI
    Tractor
    chalmers

    Default Re: Pricing hydraulic pump for IH C - best source?

    You could call Bob Gehring at G.A. Miller co 715-428-2500. He does the pump repair there.
    Here is the website hydraulic hose, G.A. MILLER COMPANY est. 1969- CALL US WITH YOUR NEEDS

Similar Threads

  1. Piston Hydraulic Pump Source?
    By S Putnik in forum Hydraulics
    Replies: 6
    Last Post: 04-23-2013, 02:20 PM
  2. Need to source Hyd pump 18 GPM Capacity at 3000 PSI
    By sweettractors in forum Hydraulics
    Replies: 12
    Last Post: 12-09-2012, 04:09 PM
  3. 1" pump discharge hose source
    By caver in forum Related Topics
    Replies: 7
    Last Post: 09-18-2009, 11:49 PM
  4. IH backhoe pump model 3613 hydraulic pump
    By martin cox in forum Parts/Repairs
    Replies: 0
    Last Post: 09-12-2008, 08:18 PM
  5. Source for hydraulic pump mounts
    By toolnut in forum Hydraulics
    Replies: 0
    Last Post: 07-15-2008, 09:08 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
© 2014 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.