Page 3 of 4 FirstFirst 1234 LastLast
Results 21 to 30 of 37
  1. #21
    Veteran Member Kernopelli's Avatar
    Join Date
    Oct 2006
    Posts
    1,583
    Location
    Carterville, Illinois
    Tractor
    Mitsubishi MTE2000D, Dig It 258 Backhoe

    Default Re: Need a support arm for Jinma 254 FEL

    DITTO on the insurance! That's what it's for. I have friends that refuse to make insurance claims because they are afraid it will raise their rates or ding their history. I dont understand that myself......why have anything but liability if you arent going to ever use it?
    Darryl

  2. #22
    New Member
    Join Date
    Feb 2013
    Posts
    11
    Location
    Hamlet, NC
    Tractor
    Jinma 254

    Default Re: Need a support arm for Jinma 254 FEL

    Insurance says they don't cover the trailer(unless listed on the policy) or anything that is on the trailer. I have a A-1 welder going to try to fix the one bent arm. Tractor and backhoe are working. Bent bucket is repaired. Might have to replace one or two cylinders on the loader.

    Need a support arm for Jinma 254 FEL-dscn2407_tn.jpgNeed a support arm for Jinma 254 FEL-dscn2438_tn.jpg

  3. #23
    Super Member greg_g's Avatar
    Join Date
    Dec 2003
    Posts
    5,983
    Location
    Western Kentucky
    Tractor
    JD3720 Cab, 300X loader with 4-in-1 bucket

    Default Re: Need a support arm for Jinma 254 FEL

    If you asked your car insurance company, you may have inquired of the wrong folks. My trailer - and whatever it's hauling - is covered under my farmowner/homeowner policy. Good place to buy inexpensive replacement cylinders is Baileys Surplus Center. Needed a pair of curl cylinders for one of my loaders a few years back. OE replacements were a ridiculous $395 each. Got an equivalent pair from Bailey for under $200 delivered

    //greg//
    USN (Ret)
    Former Chinese tractor owner (x4)
    Current John Deere owner

  4. #24
    New Member
    Join Date
    Feb 2013
    Posts
    11
    Location
    Hamlet, NC
    Tractor
    Jinma 254

    Default Re: Need a support arm for Jinma 254 FEL

    Greg,

    Thanks for the link. I will check them out and see if I can get replacements.

    I want to thank everybody for their help. It's nice to get help especially during a bad time.

  5. #25
    Elite Member SPIKER's Avatar
    Join Date
    Jun 2002
    Posts
    3,784
    Location
    Ohio, Jeromesville, Ashland County
    Tractor
    Jinma 284

    Default Re: Need a support arm for Jinma 254 FEL

    Shirtman I too would re-inquire as Greg said my insurance covers anything attached to the car/truck when towing on a trailer including the trailer. It is typical insurance with higher coverage than normal.

    MARK
    I may remember why I went to the other end of the shop, I'm just afraid once I get there I'll forget how to get back!

  6. #26
    Super Star Member Diamondpilot's Avatar
    Join Date
    Jan 2007
    Posts
    13,834
    Location
    Daleville, IN
    Tractor
    Jinma 254/284 Ford 861 Powermaster at work

    Default

    Quote Originally Posted by Shirtman View Post
    Insurance says they don't cover the trailer(unless listed on the policy) or anything that is on the trailer. I have a A-1 welder going to try to fix the one bent arm. Tractor and backhoe are working. Bent bucket is repaired. Might have to replace one or two cylinders on the loader.

    <img src="http://www.tractorbynet.com/forums/attachment.php?attachmentid=306137"/><img src="http://www.tractorbynet.com/forums/attachment.php?attachmentid=306138"/>
    I have 4 used cyliners from a loader I parted out. Give me a PM and we can work out a deal. I also have the factory control valve and all the hoses.

    Chris

  7. #27
    Advertiser
    Join Date
    Jun 2005
    Posts
    199
    Location
    Washington

    Default Re: Need a support arm for Jinma 254 FEL

    we can do you a new loader for $1800
    Coldwater Tractors, Inc.
    www.coldwatertractors.com

  8. #28
    New Member
    Join Date
    Feb 2013
    Posts
    11
    Location
    Hamlet, NC
    Tractor
    Jinma 254

    Default Re: Need a support arm for Jinma 254 FEL

    The loader arm has been repaired and should have the new cylinders & hoses on soon. She looks a little beat up but considering what she went through it's not to bad. Thanks to my local and forum help we have got the tractor back working again. The trailer is heading to the repair shop and it's sounds like it to will be back operational in the near future. Nobody was hurt and the equipment has some dents but not anywhere near as bad as we had earlier feared.


    Need a support arm for Jinma 254 FEL-dscn2624_tn.jpgNeed a support arm for Jinma 254 FEL-dscn2628_tn.jpg

  9. #29
    Elite Member SPIKER's Avatar
    Join Date
    Jun 2002
    Posts
    3,784
    Location
    Ohio, Jeromesville, Ashland County
    Tractor
    Jinma 284

    Default Re: Need a support arm for Jinma 254 FEL

    Quote Originally Posted by Shirtman View Post
    The loader arm has been repaired and should have the new cylinders & hoses on soon. She looks a little beat up but considering what she went through it's not to bad. Thanks to my local and forum help we have got the tractor back working again. The trailer is heading to the repair shop and it's sounds like it to will be back operational in the near future. Nobody was hurt and the equipment has some dents but not anywhere near as bad as we had earlier feared.


    Click image for larger version. 

Name:	DSCN2624_tn.jpg 
Views:	133 
Size:	182.0 KB 
ID:	308121Click image for larger version. 

Name:	DSCN2628_tn.jpg 
Views:	112 
Size:	143.7 KB 
ID:	308122
    That dont look too bad, (bout like my back on early rainy mornings) lol

    hope the cylinders arrive & you get them back going. Did ya get a good inspection on all the other parts? Bell housing and clutch area & front end mount area & roll bar mount area on rear axle would be areas of real concern.

    Mark
    I may remember why I went to the other end of the shop, I'm just afraid once I get there I'll forget how to get back!

  10. #30
    Advertiser
    Join Date
    Sep 2010
    Posts
    63
    Location
    Lamar, MS
    Tractor
    Jinma

    Default Re: Need a support arm for Jinma 254 FEL

    It looks as if your making good progress shirtman.

    Ben
    Circle G Tractor Sales, Inc.

Page 3 of 4 FirstFirst 1234 LastLast

Similar Threads

  1. Wanted: FEL for Jinma 254
    By mitchash in forum Wanted Ads
    Replies: 0
    Last Post: 09-08-2011, 10:32 AM
  2. Jinma 254 for $3500 with FEL?
    By tigers2007 in forum Chinese Tractors
    Replies: 25
    Last Post: 09-27-2010, 03:50 PM
  3. Broken Steering Knuckle/Arm Notrac 254
    By nt254 in forum Chinese Tractors
    Replies: 6
    Last Post: 03-13-2009, 04:11 PM
  4. New Jinma 254
    By mitchash in forum Chinese Tractors
    Replies: 6
    Last Post: 01-12-2007, 11:59 PM
  5. steering arm for Dong Feng 254
    By chainsawmike in forum Chinese Tractors
    Replies: 7
    Last Post: 05-29-2006, 12:02 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
© 2013 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.