Page 1 of 2 12 LastLast
Results 1 to 10 of 11
  1. #1
    New Member
    Join Date
    Apr 2013
    Posts
    2
    Location
    Greenville, Tx
    Tractor
    Yanmar YM2000

    Default New here and I have a problem

    Hi I'm Dean. I'm in Greenville Tx and I recently bought my first tractor. I got a YM 2000 with an original Japanese loader for $3000. Since I got it 3 months ago I have replaced the radiator due to catastrophic failure, Rebuilt the steering box because the bearings inside were completely eaten by rust, rebuilt the steering box again because I exceeded the capability of the steering boxChanged the air filter, oil filter and oil, fuel filter, repaired the gear shifter, replaced the seat and the steering wheel, and replaced the front axle pivot bushings. I think I have found just about every bolt or nut loose. And now I think I have a broken oil pump. I have already checked the oil pressure regulating valve and cleaned the oil pick up tube and still no oil pressure. It was doing great for the last couple weeks until this. Does anyone know where to get an oil pump for a YM2000? I have already checked Hoye Tractor Parts and it looks like they don't stock this part.

  2. #2
    Epic Contributor murphy1244's Avatar
    Join Date
    Nov 2011
    Posts
    20,361
    Location
    Ohio
    Tractor
    Kioti DK-40, MF-135, Ventrac 4500Y

    Default Re: New here and I have a problem

    Welcome from Ohio
    Murph

  3. #3
    Platinum Member
    Join Date
    May 2011
    Posts
    534
    Location
    NKY
    Tractor
    Yanmar YM186d,John Deere 1050, Case 211B

    Default Re: New here and I have a problem

    Contact HOYE and ask them.Not everything is shown on their site.I found 2 different oil pumps for a YM2000 on their site by going to another site and getting parts numbers. HOP-4790 has an angle tooth gear and OP-4450 has a straight tooth gear and I think fits the green Ym2000.
    JD1050,YM186D,Case211B,Homemade- sawmill & log splitter & log hauling arch trailer
    JD14T,Ford 532 balers,
    AC 80-R3,Ford 501 sickle mowers
    2.1 KW Off-grid Solar System and growing

  4. #4
    Super Star Member jerrybob's Avatar
    Join Date
    Mar 2010
    Posts
    11,415
    Location
    Somewhere in Washington
    Tractor
    yanmar 186D....JD LT180....DR Brush Cutter

    Default Re: New here and I have a problem

    I agree...call Hoye and make sure. Here's another parts dealer......Yanmar Tractor Parts and Manuals - Yesterday's Tractor Co.

    You should also post this under the Yanmar forum......some good folks with lots of knowledge out there....Good luck!
    If you say gullible really slowly........it sounds just like oranges.

    Invest in America........BUY a Politician!

  5. #5
    New Member
    Join Date
    Apr 2013
    Posts
    2
    Location
    Greenville, Tx
    Tractor
    Yanmar YM2000

    Default Re: New here and I have a problem

    Thanks for the info. I'll call Hoye this morning to see if they have a pump.

  6. #6
    Veteran Member Lou66's Avatar
    Join Date
    Nov 2012
    Posts
    1,378
    Location
    Brazoria county where Texas began
    Tractor
    Deere 990/Montana 5740

    Default Re: New here and I have a problem

    Welcome to the forum Dean,, while you are talking with them see if they have new seat.. because I believe that the only two things left.. good luck.. Lou
    "Life is good if beer is cold"

  7. #7
    Super Member deerseeker001's Avatar
    Join Date
    Jul 2011
    Posts
    7,878
    Location
    Central wisconsin
    Tractor
    International 2500a with Loader

    Default Re: New here and I have a problem

    welcome from Wisconsin
    ::welcome :::RON
    never stop learning.

  8. #8
    Elite Member The kid's Avatar
    Join Date
    Apr 2012
    Posts
    4,157
    Location
    Middle Tennessee
    Tractor
    1965 135 gasser, 1967 135 diesel

    Default

    Welcome to TractorByNet.

  9. #9
    Super Member mguitas's Avatar
    Join Date
    Aug 2011
    Posts
    7,532
    Location
    Schuylkill County Pennsylvania
    Tractor
    Massey Ferguson 1423 Hydrostat

    Default Re: New here and I have a problem

    Massey 1423, 1462 loader, wallenstein Ranch ho gx620, with subframe mount. Deere 710c

  10. #10
    Elite Member
    Join Date
    Sep 2010
    Posts
    4,096
    Location
    Canada
    Tractor
    Many

    Default Re: New here and I have a problem

    Welcome to the forum from Canada.

Page 1 of 2 12 LastLast

Similar Threads

  1. Here we go another problem !
    By G3033H in forum LS Tractor Owning/Operating
    Replies: 77
    Last Post: 02-27-2013, 11:01 AM
  2. Loader problem. (control stick problem??)
    By LVKubota in forum Kubota Owning/Operating
    Replies: 14
    Last Post: 04-20-2010, 03:49 AM
  3. Replies: 6
    Last Post: 12-14-2008, 06:21 PM
  4. UPDATE: Solved problem w/ JD 5320 startup problem
    By ClemBert in forum John Deere Owning/Operating
    Replies: 4
    Last Post: 05-14-2007, 09:55 PM
  5. Wonder if I have a problem
    By pruntyc in forum Yanmar
    Replies: 9
    Last Post: 07-11-2003, 02:55 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
© 2016 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.