Results 1 to 6 of 6
-
05-15-2012, 09:08 PM #1
SSQA to JDQA
While mowing today at the farm, I needed to do some pothole fixing but didn't have the bucket nor the JD 3203, but the 3203 bucket was there, I grabbed that and scooped up asphalt and went proceeding to spread, but got me wondering if anybody made a bracket to fit SSQA to JDQA? All I need to do is make something for bottom to hook to. Suggestions anyone?
Bobcat CT235 with Deere Imatch, And a very bad addiction of attachments
-
05-16-2012, 09:07 AM #2
A 2 or 3 in. piece of flat stock maybe 3/8 in. thick to go between the pins and some angle iron with cutouts for the bobtach lower lock pins to grab.
2008 JD 5103, FEL, 6' Frontier, 6' HD boxblade, 7' Landscape rake, More impliments to come, Bobcat (clark) 742 SS.
-
05-16-2012, 09:59 AM #3
Re: SSQA to JDQA
Would it interfere with the JDQA if you welded flat stock to bottom of the bucket protruding out far enough to mate with the bottom of the SSQA and cut holes for the pins?
Dennis
CT225 w/7TL QA FEL, 60"tooth dirt bucket, 68" smooth bucket, Pallet Forks, Bale Spear. Hydrualic top llin, QH, 48 RC, 60" tiller, Angle blade, Landscape rake, Carry-all, Post hole auger.
-
05-16-2012, 05:43 PM #4
- Join Date
- Nov 2007
- Posts
- 2,606
- Location
- .
- Tractor
- .
Re: SSQA to JDQA
I have a set of Horst forks for my JD 790 w/300 loader. I've been thinking about buying a SSQA mounting plate for my bobcat and fabricating the front of it to hook up to the JDQA of the forks.
-
05-16-2012, 06:34 PM #5
- Join Date
- Feb 2009
- Posts
- 758
- Location
- Northmost Idaho
- Tractor
- John Deere 790 w/ 300 loader
Re: SSQA to JDQA
Add more flat plate of equal thickness of the SSQA mount plates to the SSQA mount plates with holes cut out to accommodate the lower JD pins.
Add some gussets to the plate above and below the pin holes for a little more strength with holes in the gussets for the linch/keeper pin to hold the bucket on.
Clear as mud, but sure can be done it looks like790 JD W/ 300 loader
Lots of implements for loader and 3pt
Can't do it burn'n diesel, is not worth do'n
-
05-18-2012, 12:35 PM #6
I was thinking about taking a plate, about 5 inches tall and the length of the bottom pins and drill holes for the pins on the JD bucket, then weld the bottom lip on the plate for the SSQA pins. The top hooks very well. And just need the adapter for the bottom. I don't want to weld every attachment, just a adapter to fit all. Should be a pretty simple build. that way I just undo the two clips pull off the adapter and put it on other JDQA attachments. Might be something to sell.
Bobcat CT235 with Deere Imatch, And a very bad addiction of attachments
Similar Threads
-
Another SSQA three point adapter.
By countrybumpkin in forum Build-It YourselfReplies: 10Last Post: 09-09-2014, 11:26 PM -
JD QA vs SSQA
By canoetrpr in forum Owning/OperatingReplies: 8Last Post: 01-01-2012, 06:33 AM -
Any one try the JD SSQA other than RockGod?
By canoetrpr in forum John Deere Owning/OperatingReplies: 14Last Post: 09-05-2011, 07:03 AM -
Loader JDQA Adapter for 60, 70, & 70A Loaders
By C-Range in forum John Deere Owning/OperatingReplies: 8Last Post: 08-12-2010, 03:37 PM -
Quick Hitches ATI Tach All vs Aldomi SSQA
By Works 4 Jesus in forum AttachmentsReplies: 0Last Post: 07-28-2010, 10:34 PM