Page 1 of 3 123 LastLast
Results 1 to 10 of 25
  1. #1
    Silver Member Desert Bred's Avatar
    Join Date
    Sep 2013
    Posts
    216
    Location
    Goodyear AZ
    Tractor
    1998 CKC TS 254 (Fei Dong 295T1)

    Default Increasing bucket curl (rollback angle)

    Attachment 344635

    How could i increase the curl by changing the pin holes here? anyone done this?

    Also.. any danger in welding on the underside of the tractor (back axle)?
    Last edited by Desert Bred; 11-05-2013 at 05:48 PM.

  2. #2
    Silver Member kg7il's Avatar
    Join Date
    Apr 2011
    Posts
    132
    Location
    Eatonville, Washington
    Tractor
    Kubota L3800

    Default Re: Increasing bucket curl (rollback angle)

    I am getting an "Invalid Attachment" error message on your link.
    2011 Kubota L3800 HST with Loader. PHD, RC60 and LR
    2011 John Deere D120 for the wife
    KG7IL -
    Kimber Ultra Covert - No Gun Rack yet

  3. #3
    Elite Member
    Join Date
    Jul 2009
    Posts
    3,830
    Location
    SW WA
    Tractor
    Kubota BX2360

    Default Re: Increasing bucket curl (rollback angle)

    Quote Originally Posted by kg7il View Post
    I am getting an "Invalid Attachment" error message on your link.
    Maybe that is a comment on his bucket problem.


    Bruce(waiting for a good attachment)

  4. #4
    Silver Member Desert Bred's Avatar
    Join Date
    Sep 2013
    Posts
    216
    Location
    Goodyear AZ
    Tractor
    1998 CKC TS 254 (Fei Dong 295T1)

    Default Re: Increasing bucket curl (rollback angle)

    LOL

    the blue will be new lower bracket position.-img_8918-jpg
    Attached Thumbnails Attached Thumbnails -img_8918-jpg  
    Last edited by Desert Bred; 11-06-2013 at 01:11 AM.

  5. #5
    Silver Member Desert Bred's Avatar
    Join Date
    Sep 2013
    Posts
    216
    Location
    Goodyear AZ
    Tractor
    1998 CKC TS 254 (Fei Dong 295T1)

    Default Re: Increasing bucket curl (rollback angle)

    Update: That didn't work. Looks like the cylinder hole needs repositioning too. Will try this setup.
    -img_8918-jpg

  6. #6
    Platinum Member bandaidmd's Avatar
    Join Date
    Jun 2013
    Posts
    559
    Location
    DelMarVa
    Tractor
    kubota b2620,b8200

    Default Re: Increasing bucket curl (rollback angle)

    If you want more rollback the lower pin needs to go forward but if you change it to much it may not go to vertical in the dump position.

  7. #7
    Veteran Member chim's Avatar
    Join Date
    Apr 2002
    Posts
    1,763
    Location
    Lancaster County, PA
    Tractor
    Kubota L3200, Ford 1210

    Default Re: Increasing bucket curl (rollback angle)

    It looks like the bucket doesn't extend very far up/forward. If you increase the rollback, it may take a little more attention to the bucket position when lifting a load high to prevent dumping material off the back and onto your hood.

  8. #8
    Super Member
    Join Date
    Sep 2000
    Posts
    6,545

    Default Re: Increasing bucket curl (rollback angle)

    Have you thought about converting to a 4 link at the bucket? They give more roll back AND more dump angle too.

  9. #9
    Silver Member Desert Bred's Avatar
    Join Date
    Sep 2013
    Posts
    216
    Location
    Goodyear AZ
    Tractor
    1998 CKC TS 254 (Fei Dong 295T1)

    Default Re: Increasing bucket curl (rollback angle)

    Hey JB- thanks for that i never even heard of it. i'l check it out.

    I did try the repositioning of the holes like the first pick and it works much better about 5 inches back from the original.

    edit- i looked for 4 pin hole bucket on line and came up empty thus far..

  10. #10
    Veteran Member Xfaxman's Avatar
    Join Date
    Feb 2013
    Posts
    2,413
    Location
    Meridian, OK
    Tractor
    Bobcat V417 Toolcat 5610 F TORO+Loader

    Default Re: Increasing bucket curl (rollback angle)

    Quote Originally Posted by john_bud View Post
    Have you thought about converting to a 4 link at the bucket? They give more roll back AND more dump angle too.
    Quote Originally Posted by Desert Bred View Post
    Hey JB- thanks for that i never even heard of it. i'l check it out.

    I did try the repositioning of the holes like the first pick and it works much better about 5 inches back from the original.

    edit- i looked for 4 pin hole bucket on line and came up empty thus far..
    This is what he is talking about.
    -fel_diagram_large-jpg
    Notice the extra links at the bucket.
    My Avatar, the TORO+Loader: Kwik-Way FEL and TORO Groundsmaster Put Together

    Compact Telehandler:
    V417 Versahander

Page 1 of 3 123 LastLast

Similar Threads

  1. Trying to retrofit curl angle, need help.
    By fusting in forum Build-It Yourself
    Replies: 4
    Last Post: 08-10-2009, 12:35 PM
  2. MF 2350 Rollback angle
    By MEhorseFarm in forum Massey Ferguson Owning/Operating
    Replies: 4
    Last Post: 09-09-2008, 08:49 PM
  3. Increasing 400cx rollback Angle
    By rp4410 in forum John Deere Owning/Operating
    Replies: 0
    Last Post: 09-28-2007, 02:43 AM
  4. QA Bucket Rollback Angle Increaser???
    By Dougster in forum Attachments
    Replies: 94
    Last Post: 09-24-2007, 09:00 AM
  5. C-50 Specs - Dump Angle and Rollback Angle
    By BillG_in_TX in forum Century & Branson
    Replies: 11
    Last Post: 06-15-2004, 02:01 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
© 2013 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.