Results 1 to 10 of 10
  1. #1
    Silver Member
    Join Date
    Sep 2007
    Posts
    147
    Location
    Western MA
    Tractor
    JD 110 TLB

    Default Ford 335 Industrial

    I am looking at a Ford 335 Industrial loader that a friend of mine is going to sell. The problem is I can't find any info on this tractor. I know it is a 3 cyl gas and it runs very good. I have used it before helping him and it is stronger than the Ford 3500 gas loader that I have (of which I always need a little more power for things). Are there typically any problems with the 335? What HP and capacities does it have? What years were they made? Any info would be helpful.

    Thanks

  2. #2
    Veteran Member dgl24087's Avatar
    Join Date
    May 2004
    Posts
    1,398
    Location
    Va/WV
    Tractor
    1975 John Deere 1530

    Default Re: Ford 335 Industrial

    Mfg. 1975-1985. Derivative of Ford 3600 tractor. The 3600 was a 40 PTO HP tractor.

  3. #3
    Platinum Member EquipmentJunkie's Avatar
    Join Date
    Oct 2003
    Posts
    534
    Location
    SE PA
    Tractor
    Ford 1520

    Default Re: Ford 335 Industrial

    I don't know if the 335 was manufactured as late as 1985. My 1982 Ford Industrial Buyers Guide does not include a model 335 tractor. It does have the 340A, which I believe replaced the 335.

    I can't seem to find info on the 335 in my brochure and reference archives, unfortunately.

    Correction...my old 1978 Implement & Tractor Red Book has it listed under industrial tractor loaders. Here is what I found:

    PTO hp for the gas engine: 43.8 hp. from 172 cu. inches
    Three transmission options: 6x2, 6x4, 8x2
    Open center hydraulic system with 5 or 8.5 gpm @ 2100 psi
    No info on the loader.
    If it has wheels and an engine, you have my attention.

  4. #4
    New Member
    Join Date
    Sep 2012
    Posts
    3
    Location
    Hagerhill, Ky.
    Tractor
    335 Ford

    Default Re: Ford 335 Industrial

    I have a Ford 335 Tractor just bought runs good need a few parts. The PTO has a metal cap, do I have to buy parts for PTO ? Thank You, Bill

  5. #5
    Silver Member Varmint1's Avatar
    Join Date
    Jun 2012
    Posts
    170
    Location
    Deville,La
    Tractor
    JD 1010, JD 970, Farmall Super A,Komatsu D20A-5,Ford 4500,Ford 4000 forklift,Ford 640 w/703 loader

    Default

    Can you post a pic of the metal cap your talking about, some of those tractors are delete of a pto shaft, Soundguy can tell you a lot about them tractor as well as others

  6. #6
    Super Member RickB's Avatar
    Join Date
    Sep 2000
    Posts
    7,543
    Location
    Eastern NY
    Tractor
    Case 885, Ford 4000

    Default Re: Ford 335 Industrial

    Quote Originally Posted by Billy Lewis View Post
    I have a Ford 335 Tractor just bought runs good need a few parts. The PTO has a metal cap, do I have to buy parts for PTO ? Thank You, Bill
    Unscrew the cap and see if there is a PTO output shaft underneath. Probably is, if it was PTO delete it would have a flat cover attached with 4 bolts.
    We have too much gun control.
    What we need is more idiot control.

  7. #7
    New Member
    Join Date
    Sep 2012
    Posts
    3
    Location
    Hagerhill, Ky.
    Tractor
    335 Ford

    Default Re: Ford 335 Industrial

    I had to use a big pipe wrench and a cheater bar to unscrew and found the PTO out put shaft, I have another problem the middle assembly on the steering shaft was broke, son in law removed and lost some parts , need info what I need and where toget. Tec Book or print out on how to reassemble I have 3 springs, 2 pistons , 3 balls and 8 spacers ? Need help Thank You Bill Lewis

  8. #8
    Epic Contributor Soundguy's Avatar
    Join Date
    Mar 2002
    Posts
    48,624
    Location
    Central florida
    Tractor
    ym1700, NH7610S, Ford 8N, 2N, NAA, 660, 850 x2, 541, 950, 941D, 951, 2000, 3000, 4000, 4600, 5000, 740, IH 'C' 'H', CUB, John Deere 'B', allis 'G', case VAC

    Default Re: Ford 335 Industrial

    ps block? pm ultradog.. he can tell you where those balls n springs go.. he's a PS box guy.. I'm a manual steering box guy..

    soundguy

  9. #9
    New Member
    Join Date
    Oct 2014
    Posts
    1
    Location
    waelder texas
    Tractor
    335

    Default Re: Ford 335 Industrial

    i have a 2000 ford will the pto shaft fit a 335 ford industrial

    can anyone tell me thanks

    JERRY

  10. #10
    Epic Contributor Soundguy's Avatar
    Join Date
    Mar 2002
    Posts
    48,624
    Location
    Central florida
    Tractor
    ym1700, NH7610S, Ford 8N, 2N, NAA, 660, 850 x2, 541, 950, 941D, 951, 2000, 3000, 4000, 4600, 5000, 740, IH 'C' 'H', CUB, John Deere 'B', allis 'G', case VAC

    Default Re: Ford 335 Industrial

    I'm on my phone now so hard to open and swith windows, but hit the cnh parts forum and lookup both shafts and compare #

    My default guess us no..
    souNdguy

    sent from my NOKIA LUMIA

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
© 2014 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.