Results 1 to 5 of 5
-
01-06-2013, 07:35 PM #1New Member
- Join Date
- Jul 2011
- Posts
- 17
- Tractor
- JD855
Briggs 21 hp vertical shaft question
Hey everyone and HAPPY NEW YEAR!!
My year is starting out with a dead b & s 21 hp pro series in a 42" deck BAD BOY ztr mower. The battery is 100% according to my charger, but it won't even click like a relay wasn't closing. It just clicks at the ignition. This mower sits out in the weather [in hot, humid south florida] and has had "stuck" seat interlock as well as parking lock problem. i spray those connections with electronic cleaner spray and it usually starts, until today. NOTHING. The mower is three years old; the motor is a model 33m777-0116-g1. the operators manual is not much help. is there a work around other than replacing switches?
Any help or suggestions are greatly appreciated. THANKS!
-
01-07-2013, 10:28 AM #2Gold Member
- Join Date
- Dec 2006
- Posts
- 395
- Location
- Quebec
- Tractor
- Two Gravely Two L One with 10 h.p Dek-Diesel engine one Grillo 107d and one BCS 735 diesel
Re: Briggs 21 hp vertical shaft question
Hi! First Try to turn engine by hands if you can. If engine turn. Remove battery connectors at post Clean and remove all dirty as glaze .Connectors and posts must be brights. Bolts must be tights If nothing . Check all interlocks. Seat Pto Neutral switch etc..
Be careful . Can be dangerous Put hand brake. May be you can to try start directly at starter from solenoid with screwdriver. If engine turn Starter is good. They are a process for check interlock switchs. We bypass the interlock by a test wire with two alligators . Good luck! Oldmech
-
01-07-2013, 02:27 PM #3New Member
- Join Date
- Jul 2011
- Posts
- 17
- Tractor
- JD855
Re: Briggs 21 hp vertical shaft question
Thanks oldmech!
the motor turns by hand--i'm going to try the ols screwdriver jump in a little while. i'll let you know!
-
01-07-2013, 05:03 PM #4Super Star Member
- Join Date
- Sep 2003
- Posts
- 13,491
- Location
- JACKSONVILLE, FL
- Tractor
- Power-Trac 1445, KUBOTA B-9200HST
Re: Briggs 21 hp vertical shaft question
With ign off, jump directly from the battery to the start lug on the starter. and see if the engine motors over.
With switch on, do the same thing, and see if the engine starts.
If the starter tries to turn, and does not, then the valves need to be re-set. You are building to much pressure for the starter to overcome the compression .J.J.
When I works, I works hard. When I sits and thinks, I goes to sleep.
Git er done.
-
01-07-2013, 05:35 PM #5Gold Member
- Join Date
- Dec 2006
- Posts
- 395
- Location
- Quebec
- Tractor
- Two Gravely Two L One with 10 h.p Dek-Diesel engine one Grillo 107d and one BCS 735 diesel
Re: Briggs 21 hp vertical shaft question
Hi! If you have Jump cable. Try boost battery with a good one . I think your tractor battery is over 3 years for these battery is old. A battery can have a good voltage but cannot turn engine. No amps .Good luck Oldmech
Similar Threads
-
Using vertical shaft engine on wood splitter
By tnau664 in forum Build-It YourselfReplies: 15Last Post: 01-14-2013, 04:32 PM -
Vertical shaft vs horizontal??
By dlburkie in forum General Lawn & GardenReplies: 2Last Post: 06-16-2011, 07:51 AM -
Oil & Fuel Vertical Shaft Diesel engine?
By NoPaint in forum Owning/OperatingReplies: 4Last Post: 02-01-2010, 11:54 AM -
3x20 4x20 series vertical exhaust question
By KB9UDE in forum John Deere Owning/OperatingReplies: 4Last Post: 02-05-2007, 02:55 PM -
3x20 4x20 series vertical exhaust question
By KB9UDE in forum John Deere Owning/OperatingReplies: 0Last Post: 02-04-2007, 09:41 PM


Reply With Quote
