Bolens G154 / Iseki tx1300f

[fxrs55]

Hi Bolens G154/Iseki tx 1300f..

I have a Bolens G174 with a brand new Snowblower, a New set of AG Tires" dimples still on both front and rear tires" and a Back Blade. I would like to trade "Buy " a good condition snowplow for this tractor. Would you be interested? I will deliver and p/u at no charge. I have complete pic's just send me a e-mail at richard.scheer2@comcast.net

That goes for any one else who is on this site. I will also pay a good finders fee if you help me locate a good plow... Help

I don't have the front PTO so a snowblower would be of no use to me.
More importantly I use my blade for dozing more than I do for snow plowing
and I can't do that with a blower. Good luck with your search.

 

[NHmitch]

Hi Richard,

Are you looking to sell your snowblower? I only live a about an hour and a half from you. I have been looking for one, and found one the other day,and it sold by the time they got my message. I have seen a few plows in the area on craigslist. I can find them and forward them to you for free. I will look later tonight and see if I can find them. Welcome to the group!

Hi Bolens G154/Iseki tx 1300f..

I have a Bolens G174 with a brand new Snowblower, a New set of AG Tires" dimples still on both front and rear tires" and a Back Blade. I would like to trade "Buy " a good condition snowplow for this tractor. Would you be interested? I will deliver and p/u at no charge. I have complete pic's just send me a e-mail at richard.scheer2@comcast.net

That goes for any one else who is on this site. I will also pay a good finders fee if you help me locate a good plow... Help

 

[tx1300f]

are you interested in selling the transmission? 713 875 4261 my reverse is out

 

[tx1300f]

im looking for a transmission for my tx13OOf reverse is out 713 875 4261

 

[fxrs55]

I'm going to try to make a copy of the iseki trailer hitch. Here are
some pictures of a mock-up I made out of wood.
I don't have any measurements so I'm guessing and using
roughly scaled measurements from the sketch in the
parts list.

 

[NHmitch]

That looks great, and I have looked high, and low in the past to find this part, and it is next to impossible, so fabricating it is the way to go. I really like with this design, that the weight is supported by a replaceable lower link bar, and the other pins mount to the PTO side guards that were designed to hold the weight of a heavy rotavator. Keep me updated on how the progress you have with it. I can try to find some original photos. How thick are you going to make the steel

I'm going to try to make a copy of the iseki trailer hitch. Here are
some pictures of a mock-up I made out of wood.
I don't have any measurements so I'm guessing and using
roughly scaled measurements from the sketch in the
parts list.

 

[NHmitch]

I found a photo of one. Hopefully this will help a bit..Let me know if you want to make more than one!

 

[fxrs55]

I have that photo and many others but none with a clear, up close shot.
I am making all of the parts out of 1/2" thick CRS. ( 13 mm )
As I measure I am converting to the closest mm because that is
what they use in Japan and I am getting more accurate measurments

 

[fxrs55]

Here are a few pictures of the hitch I am making.
This is now made from cold rolled steel.
I think I'll use the one I made from wood for a napkin holder.
I'll give it to my wife for mothers day. And that would
be the last anyone ever hears from me! ha ha!

 

[Ilikeurtractor]

Looks great! What did you use to cut the plates? Nice work.