DS3510 4 in 1 controls

   / DS3510 4 in 1 controls #11  
I just added a second remote to my DK45. The kit was $350, but took them 3 hrs to install. After I heard what was involved installing with a cab, I decided to let them do it. Apparently it's not too bad on an open station tractor.

How much did they charge for installation? I had two sets installed before I picked up my new tractor. IIRC, the total cost was 629.00.
 
   / DS3510 4 in 1 controls #12  
How much did they charge for installation? I had two sets installed before I picked up my new tractor. IIRC, the total cost was 629.00.

I was charged 3hrs labour, but I can't remember their shop rate, but they quoted me $600. The total invoice was $1000 but included the filters and oil for the 50hr service a switch that I'm returning (because it was $50 for one of those nice lit light switchs) and 13% tax (welcome to Canada eh).
 
   / DS3510 4 in 1 controls #13  
I was charged 3hrs labour, but I can't remember their shop rate, but they quoted me $600. The total invoice was $1000 but included the filters and oil for the 50hr service a switch that I'm returning (because it was $50 for one of those nice lit light switchs) and 13% tax (welcome to Canada eh).

What light switch are you referrring to? The overhead and a switch that's controlled by opening the door?
 
   / DS3510 4 in 1 controls #14  
No, the switch that they use for the front and back worklights. I'm going to add some LED lights and wanted a consistant switch and liked how those swictchs light up when they're on. I asked my dealer for a price and he said he didn't know, but would order some to have in stock. When they came to do the 50hr service, they left a switch for me. I was a little surprised when the bill came in the mail a few weeks later.
 
   / DS3510 4 in 1 controls #15  
Here are some photos of the installation on my former DS3510. It is a WR Long 3rd function kit. The cast iron fittings were replaced with steel 2 weeks after installation. I had to order them from Surplus Center...
Hope this helps some.
Tom
 

Attachments

  • DS3510 3rd function001.jpg
    DS3510 3rd function001.jpg
    400.7 KB · Views: 138
  • DS3510 3rd function005.jpg
    DS3510 3rd function005.jpg
    362.8 KB · Views: 107
  • DS3510 3rd function004.jpg
    DS3510 3rd function004.jpg
    364.2 KB · Views: 123
  • DS3510 3rd function003.jpg
    DS3510 3rd function003.jpg
    366.7 KB · Views: 121
  • DS3510 3rd function006.jpg
    DS3510 3rd function006.jpg
    343.2 KB · Views: 97
  • Photo005.jpg
    Photo005.jpg
    371.2 KB · Views: 126
   / DS3510 4 in 1 controls
  • Thread Starter
#16  
Here are some photos of the installation on my former DS3510. It is a WR Long 3rd function kit. The cast iron fittings were replaced with steel 2 weeks after installation. I had to order them from Surplus Center...
Hope this helps some.
Tom

That's what I was after. Why did you replace the cast iron fittings?
Thanks Geoff
 
   / DS3510 4 in 1 controls #17  
Even tho I pressure tested them to 3000 PSI, I still felt more comfortable with steel hyd fittings. I had access to a hydraulic test stand. Nelson Long has it attaching to the bracket for the bucket controls and repositioning some lines before running the hoses out to the front. I bought them thru Everything attachments. When I wired it up, I attached the wires so the rocker switch would open the grapple when I pressed fwd and closed when I when aft. I really liked the handle and switch setup..

Tom
 
 
Top