Results 1 to 5 of 5
  1. #1
    Bronze Member
    Join Date
    Sep 2009
    Posts
    92
    Location
    Nova Scotia and Zephyrhills Fl
    Tractor
    BX2360 JD 425 jd 455

    Default weld on 30mm collar to accept bucket pins etc

    34LM030P2 Datasheet -- Stafford Manufacturing Corp. -- Metric Set-Screw Steel Collars -- GlobalSpec.com
    paid $3.50 ea in Canada for them.
    I`m trying to adapt a snow blade to our loader pin placement. so will weld these to some channel iron.

  2. #2
    Gold Member
    Join Date
    Nov 2007
    Posts
    483
    Location
    PA
    Tractor
    Kubota L3130 HST 4x4

    Default Re: weld on 30mm collar to accept bucket pins etc

    Watch they don't distort from the welding process. It might make pin installation difficult.
    Kubota L3130 HST 4x4, FEL LA723 w/QA, Backhoe BH90, Snow Blower: L2185 72" front mount, 7' back blade, carry all, 48" Pallet Forks w/QA, Sun Shade, Turf tires & Rubber Chains for the winter, Extra forward and rear lighting. BearCat 73454 Wood Chipper. LandPride RCR2672 Rotary Cutter. Approximately 290 hours

  3. #3
    Elite Member Chilly807's Avatar
    Join Date
    Sep 2009
    Posts
    3,219
    Location
    Nova Scotia
    Tractor
    Kubota L3400DT

    Default Re: weld on 30mm collar to accept bucket pins etc

    Princess Auto has them too, a bit cheaper I think... I welded mine 90 degrees at a time, very little distortion.

    Sean

  4. #4
    Gold Member Recoveryhill's Avatar
    Join Date
    Sep 2010
    Posts
    391
    Location
    St. Croix, Virgin Islands
    Tractor
    Kubota L3700SU

    Default Re: weld on 30mm collar to accept bucket pins etc

    It looks like that collar has sufficient wall thickness not to distort, especially if you follow Chilly's advice. Tack it in place and skip weld. Also, since it's not a high speed bushing, you could easily buff out the ID if the pin is too tight.

  5. #5
    Veteran Member
    Join Date
    Oct 2011
    Posts
    1,038
    Location
    Olalla WA, Kitsap Peninsula, West of Seattle
    Tractor
    Kubota BX25

    Default Re: weld on 30mm collar to accept bucket pins etc

    I use a shaft coupling W/O groove and cut to the length I need. They are a lot heavier and the extra thickness and length helps eliminate any distortion. When welding I run shaft through and align the weldments with each other. I buy them at Amazon in any shaft/pin size I need at the time. Metric also.

    Ron

Similar Threads

  1. Where to weld bucket hooks?
    By PACountryGuy in forum Build-It Yourself
    Replies: 94
    Last Post: 01-01-2014, 03:23 AM
  2. Backhoe Poor Bucket Weld
    By Zork in forum Century & Branson
    Replies: 21
    Last Post: 11-09-2011, 12:48 PM
  3. Weld on bucket teeth
    By hogi in forum Power Trac
    Replies: 13
    Last Post: 06-02-2008, 06:34 PM
  4. Need part number for the weld on pins for Quick Tach
    By BloomingtonMike in forum John Deere Owning/Operating
    Replies: 3
    Last Post: 10-24-2007, 09:27 PM
  5. Bucket Hooks weld-on bucket hooks
    By Stimmy60 in forum Attachments
    Replies: 11
    Last Post: 09-25-2004, 09:53 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
© 2014 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.