Results 1 to 6 of 6
  1. #1
    New Member
    Join Date
    Jul 2014
    Posts
    4
    Location
    Osteen, FL
    Tractor
    Massey Ferguson MF135

    Default Manual Steering Column Parts Needed

    1969 MF135 Perkins. Disassembled steering column due to not turning left any more. Both upper and lower cone bearings are shot, along with the upper bearing assembly. Almost all of the smaller parts need replacing. I've checked a few of my favorite sites for the parts but can only get the assembly. Can anyone suggest a place I can get the pieces and parts in the column?

    Thanks

  2. #2
    Silver Member Kenneth S's Avatar
    Join Date
    Jul 2012
    Posts
    186
    Location
    San Antonio, Texas
    Tractor
    1965 Massey Ferguson 2135 Industrial. 1996 New Holland/Ford 6640

    Default Re: Manual Steering Column Parts Needed

    I did that for my brothers 135, if we had to do it again we would get the assembly. If you are set on doing it yourself your best bet is log onto AGCO's parts site as guest, get the part numbers you need, and start looking around AGCO Parts Books I had to order parts from a few different places to get everything we needed.

  3. #3
    New Member
    Join Date
    Jul 2014
    Posts
    4
    Location
    Osteen, FL
    Tractor
    Massey Ferguson MF135

    Default Re: Manual Steering Column Parts Needed

    Thanks for the info. Like you I'm having to source from a few places. What were some of the challenges and any advice to overcome them?

    Ps
    s: I'm from San Antonio, left when I was a teen around '79.

  4. #4
    Silver Member Kenneth S's Avatar
    Join Date
    Jul 2012
    Posts
    186
    Location
    San Antonio, Texas
    Tractor
    1965 Massey Ferguson 2135 Industrial. 1996 New Holland/Ford 6640

    Default Re: Manual Steering Column Parts Needed

    So we are probably close in age. My advice is "be patient" soon as you think you have everything you need you will find something else you should have ordered.

  5. #5
    New Member
    Join Date
    Jul 2014
    Posts
    4
    Location
    Osteen, FL
    Tractor
    Massey Ferguson MF135

    Default Re: Manual Steering Column Parts Needed

    Nice, thanks. I need basically everything that goes on the shaft minus the ball nut. Gonna source everything and see where I land compared to the assy. Thanks again for the link and advice.

  6. #6
    Silver Member Kenneth S's Avatar
    Join Date
    Jul 2012
    Posts
    186
    Location
    San Antonio, Texas
    Tractor
    1965 Massey Ferguson 2135 Industrial. 1996 New Holland/Ford 6640

    Default Re: Manual Steering Column Parts Needed

    On my brothers 135 we had to go into the steering box as well once we opened it up (worn bushings, seals, a partially broken tooth on one of the gears in which we found out we should have ordered a steering gear set rather than the individual gear since the aftermarket parts are slightly different).

Similar Threads

  1. Replies: 1
    Last Post: 10-21-2013, 10:15 PM
  2. 425 Loose Steering Column or Worn Steering U Joint
    By Hotelchevrolet in forum John Deere Lawn & Garden
    Replies: 0
    Last Post: 06-19-2013, 12:50 PM
  3. TO35 Power Steering seal leak at steering column
    By imageshift in forum Parts/Repairs
    Replies: 2
    Last Post: 03-05-2013, 03:04 AM
  4. Replies: 5
    Last Post: 01-30-2013, 12:54 PM
  5. MF Industrial 203 Steering Column/Sector Help Needed
    By del7317 in forum Massey Ferguson Owning/Operating
    Replies: 2
    Last Post: 02-08-2010, 06:13 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
© 2014 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.