Tab Content
  • Arc weld's Avatar
    08-18-2016, 07:53 PM
    Arc weld replied to a thread Helpful neighbor! in Rural Living
    If she still owns the land she can't be broke. The court should be able to put a lien on the land if nothing else and should get interest. Your...
    744 replies | 177166 view(s)
  • Arc weld's Avatar
    08-18-2016, 01:25 AM
    I think you may just need to figure out how the hyd's work. There were a few different valves for aux. hyd's. Why are your draft and position...
    6 replies | 686 view(s)
  • Arc weld's Avatar
    08-17-2016, 12:39 AM
    Arc weld replied to a thread Helpful neighbor! in Rural Living
    Shield Arc isn't the type to play games and it's nice to see he's not going to roll over and pass it off as a bad experience. His neighbor needs to...
    744 replies | 177166 view(s)
  • Arc weld's Avatar
    08-14-2016, 12:49 AM
    Arc weld replied to a thread Helpful neighbor! in Rural Living
    Maybe the judge can tell the court appointed lawyer to pick this woman to make sure she shows up. I think it's a big act she's putting on and then...
    744 replies | 177166 view(s)
  • Arc weld's Avatar
    08-11-2016, 11:48 PM
    I think I'd try to find a piece of tube that fits inside and try to pull it back straight. If the piece inside pushed against the slight kink might...
    63 replies | 5026 view(s)
  • Arc weld's Avatar
    08-04-2016, 02:17 AM
    There is conflicting info on if the snap caps are approved for leaving the regulators attached. Depending on who pulls you over will determine if you...
    22 replies | 2031 view(s)
  • Arc weld's Avatar
    08-04-2016, 02:07 AM
    I guess you can't consider a Harley US made either as they used Mikuni carbs and other foreign parts. XMT 350's are a very good machine but $600...
    12 replies | 1055 view(s)
  • Arc weld's Avatar
    08-04-2016, 01:49 AM
    Error on the side of more tongue weight. I had a little emergency and had to haul my tractor with chains on and the back wheels wouldn't clear the...
    25 replies | 1758 view(s)
  • Arc weld's Avatar
    07-31-2016, 12:38 PM
    Arc weld replied to a thread MF35? in Owning/Operating
    I remember the MF30 gas I ran the exhaust was real close to the loader arms when raised and turned them a little black. I'm fairly certain the...
    26 replies | 1794 view(s)
  • Arc weld's Avatar
    07-30-2016, 08:41 PM
    Arc weld replied to a thread Flail Mower Let's talk flail mowers in Attachments
    Forward rotation (same direction as the tires) is safer as any rocks or debris will be thrown rearward. For the finest cut, reverse rotation and fine...
    3421 replies | 756260 view(s)
  • Arc weld's Avatar
    07-30-2016, 01:52 PM
    You might be able to find some non power adjust wheels at a tractor wrecker. Might even find some good used power adjust if you expand your search....
    1 replies | 505 view(s)
  • Arc weld's Avatar
    07-30-2016, 01:13 PM
    Arc weld replied to a thread Friction Welding in Welding
    I think the machines that turn the objects have a kind of clutch that releases and both parts will spin after there is enough friction (the parts are...
    15 replies | 1476 view(s)
  • Arc weld's Avatar
    07-30-2016, 01:04 PM
    The rolling forward with raised cylinders anchored is what caused the failure and that comes down to operator error. If the loader is too light for...
    29 replies | 1165 view(s)
  • Arc weld's Avatar
    07-30-2016, 12:51 PM
    Arc weld replied to a thread MF35? in Owning/Operating
    How do you know it's diesel? Judging by the exhaust it might be a gas engine. I've run an MF30 loader with the gas engine and it was a great machine....
    26 replies | 1794 view(s)
No More Results
About Arc weld

Basic Information

About Arc weld
Location (City, State):
Edmonton, Alberta
What Make/Model of Tractor Do You Own?:
MF 135
Type of Member:
Construction Pro

Statistics


Total Posts
Total Posts
1,748
Posts Per Day
1.40
General Information
Last Activity
08-21-2016 12:34 AM
Join Date
03-23-2013
Referrals
0
© 2016 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.