Have a 4 cyl Perkins on a chipper. Can't get it to run. Looks like a fuel problem.
To rule out some issues I'm running an electric fuel pump straight to the injector pump. I cracked all the lines at the injectors. With the electric pump running alone, I get alot of fuel out of one line...
I need to find an operator's manual (not parts) for a Yanmar CBL40 backhoe loader. I've searched on Google and Ebay....no luck. Does anyone have any suggestions? Thanks.
I'm working on an old Roadrunner crane...I think it's 10 ton. I need to add fluid to the hydraulic reservoir. The hydraulics run the winch, boom, outriggers, and steering. The vehicle drive is mechanical. Can anyone tell me what fluud to use, ie a tractor trans hydraulic fluid, or a motor...
I have one wire from the push button starter switch to a single post starter solenoid ( solenoid also has the large cables from battery and to starter motor). Is the push button connecting the solenoid coil to ground when pushed? I don't see any way it could be supplying positive 12v.
I've got a Yanmar compact loader backhoe, a CBL 40. Has 430 hours on it. The steering is failing....turn the wheel but its moving very little, worse one direction than the other. Came about gradually. I've put some heavy loads on this tractor. I'm guessing I need to rebuild the steering...
Have a steering problem with 450C. Bought JD tecnical manual and it does not provide much help. Im hoping I can get some direction here.
In reverse, left steering lever pulled back does not slow or stop the track. Works ok going forward. This is a problem that has gradually gotten worse...
Directional control valve not working correctly. I can only get pressure in one line. And if I use that line to lift a load via a single acting cylinder, the load drops down pretty quickly when the valve centers. I checked the cylinder by using another tractor and the cylinder is not leaking...
On 6210, won't start. I have no 12v to fuel pump. I understand the red to black wires at connector are power to pump. I have connector disconnected from pump. Switch turned on of course. Checked fuse, 30 amp. I can't trace out the wires. Don't know what to do next, any help would be...
I'm trying to resolve a fuel problem on my 6210. I have no fuel coming out of the tank. There is a 3 wire connection going into tank through a bulkhead fitting. Across 2 wires I have 6 volts so I'm assuming this is the fuel level sensor. So I'm guessing I should see 12 volts on the other...
My 6210 has always started right up. Has been parked for a couple weeks and now won't start, doesn't fire at all. Must not be getting fuel. Checked all the wiring for rat chewing and everything looks fine. What should I do to check if I'm getting fuel where it's needed? Thanks
Have a Forf 800. Never have used the aux hydraulics, ie, the couplers. Hooked up a single acting cylinder, one line, and i cant get it to move. I should be able to use a single acting cylinder, shouldn't I? How can I check this out?
Clearing the pasture of locust trees. I have a loader mounted tree shear which makes cutting them down easy. I have a 42 hp Brush Bandit chipper which grinds them up. But getting those devils into the chipper is hard work, and slow. Maybe chipping isn't worth it, but I was doing that to...
Just bought a John Deere 450C, 16,700 lb. I need to get it from St Louis to Kansas, about 380 miles. I've used Uship before but I was wondering if I could find transporters other ways. Or I might just buy a tandem dually and pull it behind my 1 ton Dodge. Any advice or know of a trailer for...
Simple question. To adjust position of drawbar, I can screw out what looks like a bolt through the drawbar (underneath tractor) but then there's another pin through the bar I can't figure out how to remove. This is on a 6210. Thanks.