Recent content by Big_Lug

MY BROTHERS 790'S FUEL GAUGE IS NOT WORKING. CAN SOMEONE CHIM IN ON HOW TO FIX IT?

I want to install a OEM temp. gauge on a D40 but can not get any help from local dealers on what part or parts I need. They have a temp gauge I can install on the instrument cluster but I am sure I need the thermostat and sending unit. Can anyone help. All the D40 has rite now is the idiot...

If anyone can reply it would sure be appreciated, how hard is it to install a factory original temp gauge for a D40. This tractor does not come with a gauge, just an idiot light, and I know I have to install the gauge in the instrument cluster, but the kicker is how do you wire it up? Just need...

I need help diagnosin a noise with the 3 point hitch. I have a Case D40, same thing as TC 40, when I lift the 3 point lever all the way up it cavitates or makes a whinning sound until I let the 3 point lever down about 1-2 inches. Is there an adjustement for this? Can someone post a solution...

First I will post pictures ASAP. This tractor came with a Woods loader, spring tooth chisel plow, 6 ft. bb, lienbach phd, and King Kutter 6 ft. finishig mower for $14000.00. The tractor has 680 hrs on it. The paint has some fading, mostly the cowling. It is a pink color now. Has anyone been able...

Will the New Holland TC 40 rear SCV kit fit a Case D40. It is over $200.00 dollars more at the Case dealer vs the New Holland dealer.I think they are the same tractor. I was priced $550.00 for the total setup.

I called my dealer yesterday and considered trading my 2004Hydro 4210 with 193 hours for a new 3038 E but my salesman told me that the 4210 was more tractor than the 3038E. He said that it weighed 900 pounds less and that the 3038 is cheaper made. Less metal less machine. I looked up the specs...

I tried to see about ordering a set of rear wheel weights for my 4210 but the JD website says they are no longer available. Any truth to this. Does anyone know where I can buy some at? I have the 17.5 in. rims. Thanks

My tractor, while driving, will just stop moving. It doesn't matter if it is reverse or forward. When iI push the pedals it shows an error code that represents a low charge in the circuit but when I move the 4 wd rocker switch back and forth it causes it to start moving again. The Motion Match...

This is pictures of me and my brother-in-law digging my pond with my JD 4210 and a rented Kubota KX-81. I first started by plowing the land with a one bottom plow then making a levee with the dirt. I dug with the front end loader down to the clay and then had to rent a mini-excavator for 1 day...

I bought a used JD 4210 a couple of weeks back and noticed when I am using the finish mower ( I cut 5 acres with it ) around 30 minutes into cutting my feet start to get very hot, the area around the foot area receives alot of heat being blown back by the engine. The average temp here in the...

Can someone give me a name of someone(company) that insures tractors. My bank is requesting me insure my tractor for theft, damages, etc. My homeowners covers liabilty while on my property and while sitting in my barn, but my banker is requesting a seperate policy, and I am not using it...

Can you use the 420 loader on skid steer type forks. I am buying a used 4210 and I have a set of skid steer forks for a larger Kubota I just sold. Can anyone tell me the pluses and minuses for the 4210. How do ya'll think it measures up to the TYM 273, the JD has 98 hrs on it, eHydro and is in...

I was wondering if anyone could help me here. I have a ZG23 and my little boy decided to turn the key in the on position, well if you do that your hours calculate and this is not the first time. By the time I noticed it calculated approximate 20 or more hours on it. Does any one know how to...

I need 2 flywheels,# 1133-400-1202A and a carburetor # HD33AL607 by Walbro. If anyone can help me, I would sure appreciate it. These new are expensive. The saws were given to me.