Tab Content
  • careyo63's Avatar
    05-14-2017, 10:20 AM
    I agree. Things to do and what not to do. But sometimes the what not takes me longer to figure out... I don't force any of my gears shifting....
    12 replies | 1819 view(s)
  • careyo63's Avatar
    05-13-2017, 11:52 AM
    The 240 has a over run clutch built in. I have a aftermarket that attaches to my PTO shaft. The problem is the attachment inertia is what is spinning...
    12 replies | 1819 view(s)
  • careyo63's Avatar
    05-13-2017, 10:38 AM
    I finally have my 2nd. Gear PTO. staying locked into gear so I use it with the FM. That way I'm running at a much lower Eng. RPM.. The wait is very...
    12 replies | 1819 view(s)
  • careyo63's Avatar
    05-12-2017, 09:03 PM
    careyo63 replied to a thread Hyd. pump whine in Yanmar
    This pic. is showing the adj. better. Not the drop rate. In it when my arms lift higher. About a 1/4" the rod will relieve pressure from the 3pt....
    11 replies | 2017 view(s)
  • careyo63's Avatar
    05-10-2017, 12:01 PM
    careyo63 replied to a thread Hyd. pump whine in Yanmar
    O-Ring around the base of the shifter cover and made sure all by vents were open. That stopped mine to a drip or so every Tach. Hr. or so. And on the...
    11 replies | 2017 view(s)
  • careyo63's Avatar
    04-28-2017, 10:41 AM
    careyo63 replied to a thread 4' Tiller in Yanmar
    Although a shear bolt or clutch would not be a bad idea it would probably just bounce off anything that was hard unless your trying to till up huge...
    21 replies | 1939 view(s)
  • careyo63's Avatar
    04-28-2017, 09:51 AM
    careyo63 replied to a thread 4' Tiller in Yanmar
    I have a shortened Dr. Shaft for it should you need one. I don't have much into it and it hasn't been used for anything for Yrs.. so I'll let it go...
    21 replies | 1939 view(s)
  • careyo63's Avatar
    04-27-2017, 04:32 PM
    careyo63 replied to a thread 4' Tiller in Yanmar
    RS 1500 behind my YM2000. My mothers garden that's been tilled by a walk behind. I agree to go through a fix everything because IMO. your YM1700...
    21 replies | 1939 view(s)
  • careyo63's Avatar
    04-27-2017, 02:44 PM
    careyo63 replied to a thread 4' Tiller in Yanmar
    Should work! Looks like it either doesn't have the rear wheels or is not an option for that model. 100.00 bucks the Dr. Shaft worth half that.
    21 replies | 1939 view(s)
  • careyo63's Avatar
    04-27-2017, 09:37 AM
    careyo63 replied to a thread 336D wont stay into gear in Yanmar
    A good guess would be the Thermostart. All the way to the bottom or if you printed it to the far Right. BLK. to Thermostart Switch. This is what my...
    8 replies | 812 view(s)
  • careyo63's Avatar
    04-26-2017, 09:54 PM
    careyo63 replied to a thread 336D wont stay into gear in Yanmar
    This should be it.....
    8 replies | 812 view(s)
No More Results
About careyo63

Basic Information

About careyo63
What Make/Model of Tractor Do You Own?:
YM2000
Type of Member:
Homeowner (11-20 acres)

Statistics


Total Posts
Total Posts
1,015
Posts Per Day
0.52
General Information
Last Activity
05-14-2017 10:26 AM
Join Date
01-06-2012
Referrals
0
© 2017 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.