Tab Content
  • Cord's Avatar
    05-24-2018, 07:38 AM
    See if this helps to answer your question. Honestly, I don't think the outlet is any different from a 120v fan being used inside of a 220v welder...
    40 replies | 1003 view(s)
  • Cord's Avatar
    05-22-2018, 03:14 PM
    It's a 220v 2p machine with a 110v duplex outlet. No neutral. Just a ground. The neutral is bonded inside of the machine. Stove and dryers used...
    40 replies | 1003 view(s)
  • Cord's Avatar
    05-22-2018, 10:24 AM
    So I bought a pair of backstand belt grinders on Sunday and I'll go back on Wednesday to pick them up. I think the first one is a direct drive 12 or...
    26 replies | 4105 view(s)
  • Cord's Avatar
    05-22-2018, 08:48 AM
    This is true. Even my late model Lincoln with a 110v outlet doesn't have a neutral. Factory bonds the neutral to the chassis. There must be an...
    40 replies | 1003 view(s)
  • Cord's Avatar
    05-20-2018, 12:26 PM
    Cord started a thread Backstand grinder in Welding
    So I bought a pair of backstand grinders yesterday. I'll go back on Tuesday to pick them up. Here's the CL post: Grinder - Polisher - Cutoff Metal...
    0 replies | 172 view(s)
  • Cord's Avatar
    05-16-2018, 03:15 PM
    Use a single wall 6" pipe and then it fits the oval. From the single wall pipe you can then adapt to the double wall pipe.
    10 replies | 618 view(s)
  • Cord's Avatar
    05-16-2018, 03:14 PM
    You should already have a grinder pump. Adding a garbage disposal should have no effect on the pump.
    15 replies | 716 view(s)
  • Cord's Avatar
    05-15-2018, 08:24 AM
    I know, I'm over simplifying it.
    41 replies | 1970 view(s)
  • Cord's Avatar
    05-14-2018, 06:37 PM
    Cord replied to a thread Well help in Projects
    I had it reversed Prior to operation, with the tank, empty of water, the pressure should be 2psi below the cut-on pressure. So, for example,...
    20 replies | 1078 view(s)
  • Cord's Avatar
    05-14-2018, 06:34 PM
    Duty cycle is very important is determining the machine's capacity. Yes, a welder might weld at 200 amps, but it'll only do it for a few seconds and...
    41 replies | 1970 view(s)
  • Cord's Avatar
    05-14-2018, 01:33 PM
    Cord replied to a thread Well help in Projects
    Here's my guess: the pressure tank pressure is not correct. If I recall correctly, if the pressure tank pressure was not set a few pounds over the...
    20 replies | 1078 view(s)
  • Cord's Avatar
    05-13-2018, 08:31 AM
    Have you been able to master the stick process or are you hoping to go to mig so its easier? If you dont have the fundamentals of stick figured out...
    41 replies | 1970 view(s)
  • Cord's Avatar
    05-02-2018, 01:57 PM
    The code has a provision in it for empirical ledger designs. For v2015, look in table R507.2. The table is for wood decks and you are over the...
    30 replies | 1401 view(s)
  • Cord's Avatar
    05-01-2018, 02:01 PM
    Thinking about building a landplane. Not certain this project will happen, but I was wondering where you guys get your blades from? Plow edges are...
    5 replies | 588 view(s)
  • Cord's Avatar
    04-30-2018, 01:58 PM
    Cord replied to a thread New 5v tin over old 5v tin? in Projects
    There are spray applied coatings that can extend the life of the existing roof. The coatings are rubber based and are applied with an airless...
    18 replies | 928 view(s)
No More Results
About Cord

Basic Information

About Cord
Location (City, State):
Richfield, Wi
What Make/Model of Tractor Do You Own?:
Resident Architect
Type of Member:
Construction Pro

Signature


Turbo Yanmar 1110d, 4wd, powershift, kwick-way loader SOLD
Waldon 5100, Cummins 4b SOLD
Gehl 6635 skid steer - Faver grapple, forks, bucket, trailer mover
Toro 328 4wd mower, 72" Lastec Deck & Toro 150 snowblower SOLD
Toro 3500 3wd mower

Statistics


Total Posts
Total Posts
1,447
Posts Per Day
0.30
General Information
Last Activity
05-24-2018 07:38 AM
Join Date
03-21-2005
Referrals
0
© 2018 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.