Tab Content
  • flyerdan's Avatar
    Today, 03:46 PM
    flyerdan replied to a thread Air Compressors in Parts/Repairs
    Air tools are real hogs, especially die grinders and cutoff tools. It would depend if you have only 110v or 220v available, and if portability is...
    3 replies | 208 view(s)
  • flyerdan's Avatar
    07-28-2016, 01:47 PM
    flyerdan replied to a thread Oil Light on in Yanmar
    It sounds like a low pressure switch that opens at 4.35 psi. You can test it with a DMM or test light circuit and poke the flat end of a drill bit...
    27 replies | 903 view(s)
  • flyerdan's Avatar
    07-27-2016, 03:22 PM
    flyerdan replied to a thread Oil Light on in Yanmar
    They do make electric oil pressure gauges, most OEM vehicles that have instruments use them. The senders are much more expensive and need to be...
    27 replies | 903 view(s)
  • flyerdan's Avatar
    07-26-2016, 08:12 PM
    I think the forum software pares some of the data in the text that shows, while retaining the integrity of the URL, as observed by hovering over the...
    9 replies | 261 view(s)
  • flyerdan's Avatar
    07-26-2016, 07:54 PM
    This thread is always one I look forward to seeing in the new posts section. I don't reply a lot here unless I think that I have something germane...
    719 replies | 84665 view(s)
  • flyerdan's Avatar
    07-25-2016, 08:22 PM
    If you want to continue the 4 rail look, make the frames out of 1.5" square galvanized tubing. I've made tons of those frames, mostly for dogear...
    17 replies | 1520 view(s)
  • flyerdan's Avatar
    07-23-2016, 08:53 PM
    flyerdan replied to a thread sanding disc grit in Welding
    36 for smoothing welds and on the 12" disc sander for shaping. If finish matters take out the swirl marks with 80 and go over it with scotchbrite...
    5 replies | 515 view(s)
  • flyerdan's Avatar
    07-23-2016, 07:25 PM
    What did you manage to find costing nearly a grand that isn't in the massive exclusion list for the 25% off coupon?
    6214 replies | 1214628 view(s)
  • flyerdan's Avatar
    07-23-2016, 05:01 PM
    flyerdan replied to a thread Pipe saddle in Build-It Yourself
    The Lenox brand hole saw stands up pretty good. I used them to cut copes in 2.375 for the ends of cantilever gates. It was a 1.875" hole saw and I...
    18 replies | 1058 view(s)
  • flyerdan's Avatar
    07-18-2016, 01:44 PM
    flyerdan replied to a thread Replacement starter in Parts/Repairs
    If the gear pitch is the same, it doesn't matter how many teeth are involved. Going to a larger diameter starter gear would require more teeth for...
    12 replies | 516 view(s)
  • flyerdan's Avatar
    07-16-2016, 01:30 PM
    flyerdan replied to a thread What is this in Photos
    I've been coming back to this hoping that someone has an answer. It looks like some kind of bearing. Try putting the middle pic in Google image...
    9 replies | 503 view(s)
  • flyerdan's Avatar
    07-15-2016, 01:39 PM
    If the ID is big enough, you could use a couple chunks for fork sleeves to keep from damaging fragile items, or scuffing the paint on that new...
    21 replies | 1136 view(s)
  • flyerdan's Avatar
    07-14-2016, 05:30 PM
    I have the 10 ton porta power, like IT found a deal on craigslist that was un-pass-upable* at $60 for what looked like an unused set. It's not...
    6214 replies | 1214628 view(s)
  • flyerdan's Avatar
    07-10-2016, 11:44 PM
    It looks like you have some lag hinges already in the post for gates that were there at one time. I have an Excel spreadsheet that generates cut...
    17 replies | 1520 view(s)
  • flyerdan's Avatar
    07-10-2016, 07:24 PM
    It's hard to tell from the pics if those are made from that brittle pot metal that they make carburetors out of or if it's galvanized. Couldn't...
    8 replies | 712 view(s)
  • flyerdan's Avatar
    07-09-2016, 08:06 PM
    I built a basket a while back out of salvaged material I had laying around. The 4' chunk of catwalk was ideal for the base, the square top was from...
    15 replies | 985 view(s)
No More Results
About flyerdan

Basic Information

About flyerdan
Location (City, State):
Salem, OR
What Make/Model of Tractor Do You Own?:
Hyster H50
Type of Member:
Homeowner (under 1 acre)

Signature


Whoever said that you can't fight city hall had obviously never met Marvin Heemeyer.

Statistics


Total Posts
Total Posts
655
Posts Per Day
0.36
General Information
Last Activity
Today 05:50 PM
Join Date
08-09-2011
Referrals
0
© 2016 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.