Today, 11:35 AM
Did yours have the notches or the holes in the shank?
8 replies | 159 view(s)
Today, 11:31 AM
I have to second the notion of checking the frame where the hitch is bolted too. I had the frame rot out on the hitch on my Jeep once and barely...
15 replies | 654 view(s)
Today, 10:38 AM
I have to agree with Eddie, last time I checked, spray foam was about triple the cost for just the product for DIY, even more if it is done by a...
17 replies | 1048 view(s)
Today, 10:13 AM
By the way, the shanks aren't cast iron, they might be cast steel but more likely they are forged steel. They are weldable as I have welded back...
8 replies | 159 view(s)
Today, 10:09 AM
From what I have seen, there are two types of shanks, the ones with a notch in the front AND the better ones with a hole in the middle of the shank...
8 replies | 159 view(s)
02-26-2017, 11:25 AM
My only complaint with the HF AD helmets is lack of grinder mode. I would love to use it to grind with, but it darkens with the sparks so I have to...
32 replies | 1897 view(s)
02-26-2017, 11:10 AM
I have both landscape rake and box blade and after some initial use pulling down a hill and levelling it to build my shop, I haven't used either. ...
26 replies | 1843 view(s)
02-25-2017, 01:50 PM
It is going to have to grow a lot more before it can be identified, perhaps late spring a photo might work for someone.
19 replies | 750 view(s)
02-24-2017, 10:58 AM
R4 tires aren't much better than street tires when it comes to mud, especially clay mud. They slick over pretty fast and then it is all over as far...
6758 replies | 1034974 view(s)
02-24-2017, 10:43 AM
That screen looks just like the one on my RTV900 (no cab) so I am thinking that screen is an OEM screen and you may just need the mounting brackets...
13 replies | 559 view(s)
02-22-2017, 12:25 PM
I got some of the free batteries once. Put them in my camera and got the "low battery" warning from the get go. Not enough power to operate the...
6952 replies | 1399720 view(s)
02-22-2017, 12:04 PM
I would say get all the chunks of gear metal out, fill it with moly grease and put it back together. After fully assembled, top off with about 4 oz...
24 replies | 1694 view(s)
02-22-2017, 11:46 AM
I hope you aren't planning to clear cut the other 4 acres. A few trees always make the property look nice, not a thicket or cluster of saplings, but...
4 replies | 1072 view(s)
02-21-2017, 12:12 PM
I run my B26 almost always in 4 WD as long as I am in my pasture. If I go on any hard surface like a road or concrete drive, I put it in 2 WD to...
24 replies | 2540 view(s)
02-21-2017, 12:03 PM
I got a puncture on one of my rears on my B26 TLB while helping a neighbor repair some roads in their RV park. I hauled my compressor down there and...
11 replies | 1896 view(s)
02-21-2017, 10:08 AM
10 PSI in the rears is about right for good ground contact. I would never run the rears OR fronts at or above the max rating. I only run enough...
12 replies | 1174 view(s)
02-21-2017, 10:02 AM
I don't think a new tractor should have any seals leaking. I would consult my dealer to have that seal fixed while under warranty.
13 replies | 525 view(s)
02-20-2017, 12:13 PM
In my previous residence, I replaced my 20 year old unit with a larger by 1 ton new high efficiency AC. The installer, used the old 3/4" return as a...
64 replies | 3389 view(s)
02-20-2017, 12:01 PM
Maybe you could bend that step so it isn't so much angle, then it would be closer to the ground. Or you could make an additional step and use chain...
7 replies | 962 view(s)
02-19-2017, 11:33 AM
If the clutch is like the one on my 6 foot KKII(no exposed springs) then it should not be adjusted according to my info. It appears to be sealed...
20 replies | 1782 view(s)
02-19-2017, 10:28 AM
Not completely sure why, but we always left the combine header raised. I think it was so water wouldn't stand in the belly of the header, with it...
31 replies | 4078 view(s)
02-19-2017, 09:50 AM
Most vehicles now come with a oil change computer that tells you when to change based on engine RPM, engine temps and other use related items. Every...
37 replies | 1796 view(s)
02-18-2017, 10:47 AM
The biggest issue is money, do you want to spend the money (double or triple cost) on a super heavy duty box blade or not. I bought a medium duty BB...
25 replies | 1906 view(s)
02-18-2017, 10:24 AM
I thought the products might be good from the ads, but after seeing the prices, NO WAY. No undershorts made in Bangladesh or China is worth $15...
53 replies | 2957 view(s)
02-18-2017, 10:04 AM
Lots of folks brag on their Mahindra tractors. The only Mahindra I ever saw in person was at the LS dealer when I was shopping for tractors and in...
37 replies | 2363 view(s)
02-18-2017, 09:49 AM
I think you have a good idea for those needing a manlift. It already has the FORK pockets so it should work with just a plywood bottom to stand on. ...
23 replies | 2241 view(s)
02-17-2017, 06:43 PM
Using a dozer is good advice. Even with the tractors that me and brother in law have (NH2310, my Kubota B26 and my LS P7010) it is still...
25 replies | 2229 view(s)
02-17-2017, 05:43 PM
One of my remotes froze up, but by applying a bit more force it broke loose. I try to remember to move it from time to time now. I don't know what...
1 replies | 463 view(s)
02-13-2017, 02:21 PM
IRT laundry: I have found that if staying a hotel while on vacation or business trip, in house laundry service is just about as high as buying new...
28 replies | 1672 view(s)
02-13-2017, 11:52 AM
Wild boar is best left to buzzards, after all they need to eat too. A guy gave me a butt roast from a wild boar and it stunk so bad when cooking...
11 replies | 1122 view(s)
- Date of Birth
- December 8, 1949 (67)
About Gary Fowler
- I grew up on a farm driving 8N Fords when I was 5. We had a 9000 Ford when my Dad decided to retire
- Location (City, State):
- Bismarck Arkansas
- Fishing, Driving my tractor and tinkering with my welder and shop equipment
- I am a retired Quality Manager for a large engineering and construction company
- Real Name:
- Gary Fowler
- What Make/Model of Tractor Do You Own?:
- 2009 Kubota RTV 900, 2009 Kubota B26 TLB & 2010 model LS P7010
- 8' disc, 7' Bush hog, 6' box blade, FEL,cultivator,back blade, post hole digger
- 24 years of farming 400+ acres
- Lot Size:
- Currently 12 acres + 30 acres of Brother in Law adjoining that we hellp each other with
- Type of Member:
- Homeowner (11-20 acres)
2010 LS P-7010C 20F/20R gear tractor & FEL, 2009 Kubota B 26 TLB, RTV 900 Kubota,17 foot Lund boat with 70HP motor, 2012-20 ft 12k GVW trailer, 2011- 52" Craftsman ZTR mower, 2013 Ferris Zero Turn, 3 weed whackers, pressure washer, leaf blowers, 7 foot bush hog, 8 foot landscape rake , 8 foot 3 PH disc, 2 row cultivator, 350 amp Miller AC/DC welding machine and all the tools needed to keep them all repaired and running.
- Total Posts
- Posts Per Day
- Last Activity
- Today 11:35 AM
- Join Date