Recent content by jeepcoma

Added the pigtail to my wiring harness and that was the easy part. I spent way too much time trying to get all the wires to fit underneath the console. JD could have made this very very easy, but it was an annoying struggle. Form over function unfortunately! Oh well, I'm only going to have...

Must be my lucky day! Everything I had ordered to wrap up my rear remote install showed up today, just need to run to the store and get some more 90* hydraulic fittings and I should be able to get this all in done over the weekend. Hose wrap and protectors from Outback Wrap. Here's the Tyco...

April 23, 2024 - Forks Took a drive today... Picked up the Artillian 3000 lb frame, 36" forks, and the backrest. My original idea was to get the lightest weight components possible to maximize the limited lift capacity of these smaller tractors, which would have been the 2300 lb frame and...

I did some more searching and came across the following part number: 1-1703498-1-PT This led me to Tyco 1-1703498-1-PT - Vormontierter 2 poliger gedichteter maennlicher MCP / MCON Stecker mit Kabel, Kodierung A It's the same female housing, but with a wiring pigtail already installed...

It was not explored in my other thread, I only mentioned that I found it. I started a new thread for collecting information in a visible way, for other members and future searches.

I've been looking for information about the factory power tap under the rear console on my 2025R (it's the updated console (2022?) with the 4 switch knockouts). In the parts catalog it's #5 here on the fender wiring harness: There are multiple PNs listed for this: Elec. Connector Housing -...

Apr 14, 2024 - Rear Remote Progress Spent some time getting the rest of the Summit rear remotes and Fit Rite top-and-tilt kit together. Most of the time by far was spent routing, test fitting, rerouting, repeat. First I pulled out the right rear fender and handle so I could get access to the...

Fit the Summit Hydraulics manifold to the ROPS. I installed the each of the male dust plugs with the corresponding female half, with the idea being that when I pull them out to put a line in, I'll have fit the male and female covers together and keep them clean. It's way too busy back there...

Got the manifold and all fittings put together finger tight last night - pretty straightforward. Getting those switches out, now THAT was a pain. First, inspection. Here's the grommit the wiring harness passes through (from the inside): Without the flash, there's a lot of daylight visible...

Upgrades!! March 25, 2024. After a long winter without much tractoring action, spring is in the air and I have a few upgrades to put in during mud season. First, nothing very exciting, but cheap insurance: I don't have any plans to use the tractor during winter so this should help keep the...

I inquired about the TKV20 back on 10/10/23 and for future reference here was what I was quoted:

They're here! I ordered these 5/24/23 and they arrived 12/26/23. I'd planned to do this as a late winter/early spring install but I might do it in January. It's been so unseasonably mild here in NH that there is no snow on the ground and I'm still using the tractor. I still need to do some...

I showed another sneak peak earlier, and here's the post on it. I didn't stop at the Hydros+ pump upgrade, I didn't stop at the Hydros+ cooler, and I went for the Hydros+ Turbo kit. I was more hesitant about this than the other upgrade because it fundamentally changes the tractor and increases...

Anything in particular you'd like to see? Already showed the installed version in post 22 above. Oh, one thing I didn't write about above is installing the Otis Axle Vent. When I had the front fairing off I ran the vent tube up through a hole into the engine bay. I believe older model years...

OK so I gave a sneak peek at the finished installation, but the "next big thing" I did was install the Hydros Plus Cooler. I had my eye on it early on but frequently thought "JD knows best and has sized the hydraulic cooler appropriately". Well, that may be true to satisfy their warranty...