Tab Content
  • johara1's Avatar
    08-19-2017, 07:39 AM
    johara1 replied to a thread New Deck in Ventrac
    I seen it was not a good deal so I did trade my old (new) deck in on the new one with the hydraulic. tilt and it super it cost me money but it was...
    15 replies | 4258 view(s)
  • johara1's Avatar
    08-12-2017, 08:04 AM
    johara1 replied to a thread Mowers in Ventrac
    Simply remove the side chute, end of story...... Jim
    6 replies | 2415 view(s)
  • johara1's Avatar
    08-11-2017, 10:27 AM
    johara1 replied to a thread Mowers in Ventrac
    Having had a Steiner side discharge mower and it was the worst of the three. it dug in on the roller mount where slopes changed and bounced due to...
    6 replies | 2415 view(s)
  • johara1's Avatar
    08-09-2017, 09:12 AM
    johara1 replied to a thread Capabilities of a Ventrac in Ventrac
    This is about the only way the slip scoup with a grappler is ok and is a great tool to have but you may never use the grappler part again. the stump...
    7 replies | 2169 view(s)
  • johara1's Avatar
    08-04-2017, 07:07 AM
    johara1 replied to a thread Capabilities of a Ventrac in Ventrac
    I don't think Ventrac will work for you. They are a great mower and they get around good but their hydraulic are very weak and not suitable for real...
    7 replies | 2169 view(s)
  • johara1's Avatar
    08-01-2017, 11:05 AM
    johara1 replied to a thread new deck in Ventrac
    All 1/4 28 grease fittings are not the same, very generous tolerance. Less than a 50% thread.... On a good note I have my tilt cylinder kit...
    23 replies | 4772 view(s)
  • johara1's Avatar
    07-30-2017, 04:47 PM
    I will try again for the last time. Do not try to travel........ pick it up with the hydraulic. and articulate the center pin away from the problem,...
    28 replies | 3449 view(s)
  • johara1's Avatar
    07-26-2017, 04:05 PM
    I can tell you guys never run equipment ....... I know the hydraulics are kind of anemic but it will still work. I guess if you had a 992 that slid...
    28 replies | 3449 view(s)
  • johara1's Avatar
    07-25-2017, 12:25 PM
    johara1 replied to a thread New 4500P Review in Ventrac
    I found when changing oil and filter a cheap throwaway pan to do a large turkey slides under the machine and will get the oil from both the filter...
    4 replies | 562 view(s)
  • johara1's Avatar
    07-25-2017, 09:48 AM
    If you pick it up by pushing down on the attachment then articulate it away then set it down and keep doing it till you are free. don't try to use...
    28 replies | 3449 view(s)
  • johara1's Avatar
    07-24-2017, 08:40 AM
    you have to lift it off the ground when you articulate away, then set it down and articulate the other way ..... Jim
    28 replies | 3449 view(s)
  • johara1's Avatar
    07-24-2017, 08:35 AM
    johara1 replied to a thread New 4500P Review in Ventrac
    You are right on hooking up, but I beat that by disconnecting the seat switch so I can hook up from beside the machine. The fuel thing, I find it...
    4 replies | 562 view(s)
No More Results
About johara1

Basic Information

About johara1
Location (City, State):
western pa.
Interests:
shooting,labs
Occupation:
heavy equip. operator
Real Name:
james O'Hara
What Make/Model of Tractor Do You Own?:
Ventrac 4500P
Attachments:
mower,bucket,blade
Hours:
0
Lot Size:
2+acers

Statistics


Total Posts
Total Posts
467
Posts Per Day
0.09
General Information
Last Activity
Today 07:19 AM
Join Date
02-21-2003
Referrals
1
© 2017 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.