Tab Content
  • jonsstihl's Avatar
    Yesterday, 11:57 AM
    jonsstihl replied to a thread log splitter valve in Hydraulics
    anyone with the regen splitter valve. Can you tell if the rapid extend is the first soft detent or the second one.
    29 replies | 718 view(s)
  • jonsstihl's Avatar
    Yesterday, 11:55 AM
    jonsstihl replied to a thread log splitter valve in Hydraulics
    so what I thought was the regen dump circuit on my loader is actually the regular dump circuit and turns out I've been using the regen circuit all...
    29 replies | 718 view(s)
  • jonsstihl's Avatar
    Yesterday, 11:52 AM
    jonsstihl replied to a thread log splitter valve in Hydraulics
    just found another post explaining the regen valve. so you end up using the oil from the rod end to supplement the oil going to the base but you...
    29 replies | 718 view(s)
  • jonsstihl's Avatar
    Yesterday, 11:38 AM
    jonsstihl replied to a thread log splitter valve in Hydraulics
    just looked into the valve but with 9.4 gpm on my next tractor I am almost two times over the max gpm of the valve
    29 replies | 718 view(s)
  • jonsstihl's Avatar
    Yesterday, 11:35 AM
    jonsstihl replied to a thread log splitter valve in Hydraulics
    Thanks for the discussion, I am learning things. I was under the impression regen was to stop the flopping around of a bucket when dumped with a...
    29 replies | 718 view(s)
  • jonsstihl's Avatar
    Yesterday, 06:33 AM
    jonsstihl replied to a thread log splitter valve in Hydraulics
    I'm currently running a 3.5" cylinder with 2000psi on the tractor and somewhere around 6gpm on my b7800 and it does the job. It is slow but fast...
    29 replies | 718 view(s)
  • jonsstihl's Avatar
    06-18-2018, 10:03 PM
    jonsstihl replied to a thread log splitter valve in Hydraulics
    looking at the parts catalog for the prince ls 3000 valve there appears to be only one detent spring. what makes the spool center in the other...
    29 replies | 718 view(s)
  • jonsstihl's Avatar
    06-18-2018, 09:48 PM
    jonsstihl replied to a thread log splitter valve in Hydraulics
    I was just writing to surplus center asking them about that and I realized that if I just remove one spring from the spring to center mechanism and...
    29 replies | 718 view(s)
  • jonsstihl's Avatar
    06-18-2018, 09:39 PM
    jonsstihl replied to a thread log splitter valve in Hydraulics
    there is a lever that on the splitter that is actuated by the rising wedge that manually returns the valve to the neutral position against the spring...
    29 replies | 718 view(s)
  • jonsstihl's Avatar
    06-18-2018, 09:12 PM
    jonsstihl replied to a thread log splitter valve in Hydraulics
    I lowered the 3pt hitch on my father in laws so I don't have to bend down to split. I usually split with the 3pt raised all the way up. A 3pt log...
    29 replies | 718 view(s)
  • jonsstihl's Avatar
    06-18-2018, 04:56 PM
    jonsstihl replied to a thread log splitter valve in Hydraulics
    thanks for the link to the calculator, didn't realize there was one. The trunnion mount is so the vertical only splitter can be dropped from...
    29 replies | 718 view(s)
  • jonsstihl's Avatar
    06-18-2018, 11:57 AM
    jonsstihl replied to a thread log splitter valve in Hydraulics
    can anyone do the math assuming a 24 inch stroke and 10gpm flow what is the difference in cycle time between a 3.5 inch cylinder and a 4 inch...
    29 replies | 718 view(s)
  • jonsstihl's Avatar
    06-18-2018, 11:35 AM
    jonsstihl replied to a thread log splitter valve in Hydraulics
    I don't think I can get the auto kickout with the valve springing to a work port but I thought it would be nice to have because I've had the stop...
    29 replies | 718 view(s)
  • jonsstihl's Avatar
    06-18-2018, 11:29 AM
    jonsstihl replied to a thread log splitter valve in Hydraulics
    thanks for the replies, the splitter I borrow has a single lever valve which does not spring to center it springs to the work port so as soon as you...
    29 replies | 718 view(s)
  • jonsstihl's Avatar
    06-17-2018, 09:31 AM
    jonsstihl replied to a thread log splitter valve in Hydraulics
    Welded Log Splitter Cylinder - 3/4" Work Ports, 4" ID x 24" Stroke x 2.25" Rod OD, 1.5" Rod End, Trunnion Mount - Cylinders - Parts | RuggedMade ...
    29 replies | 718 view(s)
  • jonsstihl's Avatar
    06-17-2018, 08:36 AM
    jonsstihl replied to a thread log splitter valve in Hydraulics
    surplus center site seems down, Is there another site that has lots of choice in cylinders
    29 replies | 718 view(s)
  • jonsstihl's Avatar
    06-17-2018, 08:35 AM
    jonsstihl replied to a thread log splitter valve in Hydraulics
    I have a few more details looks like I need a crosstube mount on the rod and a flange mount on the head side of the cylinder(where the rod comes out)
    29 replies | 718 view(s)
  • jonsstihl's Avatar
    06-17-2018, 08:17 AM
    jonsstihl replied to a thread log splitter valve in Hydraulics
    I've done a little research and seems like I need a centerline flange mount at the head.
    29 replies | 718 view(s)
  • jonsstihl's Avatar
    06-17-2018, 08:12 AM
    Is there such a thing as a log splitter valve that will operate like I want . I want to be able to push down and have the cylinder extend and...
    29 replies | 718 view(s)
  • jonsstihl's Avatar
    06-04-2018, 06:08 PM
    jonsstihl replied to a thread Flail Mower Let's talk flail mowers in Attachments
    Jthibideau89, Did you try the scoop knives before installing the side slicers. I have side slicers on my MOTT 72 but I was wondering which style...
    5186 replies | 1285220 view(s)
No More Results
About jonsstihl

Basic Information

About jonsstihl
Location (City, State):
Quebec, Canada

Signature


James
KUBOTA B7800, LA402 FEL, LAND PRIDE BB1560, PRONOVOST PUMA-64
JD X758, POWERFLOW BAGGER

Statistics


Total Posts
Total Posts
191
Posts Per Day
0.05
General Information
Last Activity
Yesterday 01:21 PM
Join Date
09-02-2008
Referrals
0
© 2018 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.