Tab Content
  • jwmorris's Avatar
    Yesterday, 11:13 PM
    Sounds like you have it covered. The "digging capability" of a land plane is limited by the skids though and all your doing with the top link is...
    54 replies | 6297 view(s)
  • jwmorris's Avatar
    Yesterday, 10:30 PM
    If you are going to add hoses and a hydraulic cylinder to the equation, why not make it useful for all of your implements instead on just one and at...
    54 replies | 6297 view(s)
  • jwmorris's Avatar
    09-25-2016, 07:31 PM
    Why not weld it solid and add a hydraulic top link? Surly this isn't the only implement you have where it would be useful.
    54 replies | 6297 view(s)
  • jwmorris's Avatar
    09-24-2016, 10:51 PM
    What does that do that the regular top link wouldn't do, if it were welded solid and didn't have all the extra parts?
    54 replies | 6297 view(s)
  • jwmorris's Avatar
    09-24-2016, 09:13 AM
    This is one I built but you can see how to reinforce the channels,, your not boxing them rather triangulating them. Also how I built my press brake...
    60 replies | 12429 view(s)
  • jwmorris's Avatar
    09-22-2016, 11:19 AM
    jwmorris replied to a thread How to fix this crack in Welding
    Yep, my Grandfather used exhaust from the engine from his welder for many years, until one blew up. It didn't kill him but he quit relying on that...
    92 replies | 5649 view(s)
  • jwmorris's Avatar
    09-22-2016, 11:12 AM
    Drop a strip of cardboard or wood between the moving jaw and parts. They will still be consistently spaced by the rear jaw and the strip will...
    54 replies | 6297 view(s)
  • jwmorris's Avatar
    09-18-2016, 01:04 AM
    jwmorris replied to a thread How to fix this crack in Welding
    The one on the side is perfect. The one on the top would have been better if both ends were not welded and instead had the weld beads continue on...
    92 replies | 5649 view(s)
  • jwmorris's Avatar
    09-18-2016, 12:59 AM
    3/8" thick H beam is what we used with a 4" cylinder and 16 GPM pump on an 8hp engine. Spends most of its time running just above idle.
    9 replies | 1626 view(s)
  • jwmorris's Avatar
    09-18-2016, 12:52 AM
    I punched the carriers for my blades and side plates for adjustment from 1/2" above grade to an inch and a half below (with rippers that can go...
    54 replies | 6297 view(s)
  • jwmorris's Avatar
    09-15-2016, 02:26 PM
    jwmorris replied to a thread How to fix this crack in Welding
    Back gas the inside with an inert gas will keep you safe and put a plate on top and oval/diamond shaped ends would be best or if you use a rectangle...
    92 replies | 5649 view(s)
  • jwmorris's Avatar
    09-14-2016, 10:55 PM
    Life depends a lot on how hard it is, just saying you can double it, for blades, if you pick the right one.
    54 replies | 6297 view(s)
  • jwmorris's Avatar
    09-14-2016, 09:12 PM
    If you go back look for blades with center mounting bolts. If you find these you can flip them over and get twice the life out of one blade. ...
    54 replies | 6297 view(s)
  • jwmorris's Avatar
    09-13-2016, 11:41 AM
    jwmorris replied to a thread Tig welding cast iron in Welding
    I have repaired countless cast iron parts using silicon bronze filler and DC with a TIG.
    15 replies | 1805 view(s)
  • jwmorris's Avatar
    09-13-2016, 11:28 AM
    You might look in to them, you don't need a step up transformer, they do that too. You can run 240v 3 ph motors on a regular 110v outlet. For...
    54 replies | 6297 view(s)
  • jwmorris's Avatar
    09-11-2016, 01:20 PM
    I built one not too long ago but after adding up the price of blades and rippers I decided to just use an extra box blade I picked up from Craigslist...
    54 replies | 6297 view(s)
  • jwmorris's Avatar
    09-10-2016, 09:14 AM
    The extra mast I have is only "powered" in one direction. If yours is off a lift that rides around on the back of a semi trailer it will likely be...
    9 replies | 1626 view(s)
  • jwmorris's Avatar
    09-09-2016, 10:30 PM
    jwmorris replied to a thread 380 shot shell in Build-It Yourself
    The last one I built was just for checking loads, 1/4" plate and a 1/2" thick AR 500 plate at 45 deg into sand. Not for long range at all but...
    37 replies | 4597 view(s)
  • jwmorris's Avatar
    09-08-2016, 08:28 AM
    jwmorris replied to a thread 380 shot shell in Build-It Yourself
    Would be quite a bit, that's fast for a bullet that heavy. Maybe deflect it with AR 500 plate on an angle first and it would take a lot less.
    37 replies | 4597 view(s)
  • jwmorris's Avatar
    09-07-2016, 09:22 PM
    jwmorris replied to a thread 380 shot shell in Build-It Yourself
    That is 3/8" plate steel. About 4000 lbs of it. Gives you a large margin of error and contain all bullets sent down range.
    37 replies | 4597 view(s)
  • jwmorris's Avatar
    08-30-2016, 03:03 PM
    jwmorris replied to a thread 380 shot shell in Build-It Yourself
    .221 fireball will be too thin to turn, the only reason a .223 works is because the web is so thick that low. 38/357 is a completely different...
    37 replies | 4597 view(s)
  • jwmorris's Avatar
    08-29-2016, 04:23 PM
    jwmorris replied to a thread 380 shot shell in Build-It Yourself
    Had an idea the other day and had a few min to see how it would work. I took a spare Lee powder through die I had and removed the flare portion...
    37 replies | 4597 view(s)
No More Results
About jwmorris

Basic Information

Statistics


Total Posts
Total Posts
660
Posts Per Day
0.20
General Information
Last Activity
Yesterday 11:23 PM
Join Date
10-03-2007
Referrals
0
© 2016 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.