Ok many of you read my post about installing a new ip on my kama ts354c. Well I thought all was well and it was ready to go back to work until this afternoon. As soon as I got started brush hogging I slowly ran out of power until it would barley even idle. After it idles for a while I can again...
Some of you may had read my older post about injector pump problems on my TS354C. I have only 70-80 hours on my tractor now. Roughly 20 hrs ago I noticed some diesel fuel and very fine brass dust like shavings getting into the injector pump oil when I changed it, and it has only gotten worse...
I have found a new accutech loader for sale locally that is for a Kama 454. I want to purchase it for my ts354c. I am sure it will work all but the mounts. I have googled accutech loaders and cant find their website or any contact info. I need to call them to check on purchasing mounts for my...
I wanted to ask how serious my injector pump problem is. My Kama Ts354c has 70 hrs and I have changed the injector pump oil atleast two times. I always noticed the oil level was high due to diesel getting into the oil. The last time I used my tractor I notice a steady drip of something coming...
Im trying to get some ideas on why my Kama TS354C wont rev to the max rpm(green area on the tach). It pulls to about 300 rpm short. I have adjusted the tach sensor, and I adjusted the valves. About all of them needing tightening a bit and I thought that would help. I have about 60hrs on it now...
I am considering buying a FEL for my TS354C or building one. There are no rear remotes so how does the hydraulics hook up? and what size shaft hydraulic cylinders would work the best with this tractors hydraulic output?
My Kama has about 37 hours on it now and im wanting to change the power steering, hydraulic and axle oil. On the power steering the factory fluid is seeping past some of the connections and maybe on the steering rack seals also.What fluid should I use in the power steering? Also is the hydraulic...
Just curious what this electrical plug could be used for on the back of my ts354c. I have thought about building a sprayer, could this be used as a connection for power if I use a elctrical pump instead of a pto pump?
I picked up one of the Napa 3195 fuel filters yesterday. Mine still has the original blue one and 23 hrs. I know when I change it I should fill it with fuel but what is the procedure for using the primer to get the rest of the air out? Is there a bleeder to open while you use the plunger? My...
On my TS354C i have been considering turning the wheels inside out for a wider track and more stability. My question is has anyone done that before? The way the wheels are dished it would make the stance considerably wider. The only problem i see is having to reverse the weights on the rear...
I was changing motor oil for the first time on my Kama TS354C with 10 hrs so I thought I would check the injector pump oil also. I noticed that mine has a dip stick instead of a screw to remove for the oil level like some of the Jinmas. When i removed the dip stick oil gushed out of the dip...
I got my Kama out to use for the first time at night, it was in the mid 40's and very damp feeling. After the tractor got warm it continued to exhaust white smoke, or could it have been condensation such as an automobile produces when its cold outside. It was hard to tell because the only light...
I see alot of you guys talking about using the decrompession lever on your tractor. Mine is of course a Kama ts354c. This morning it was a little hard to start in the cold weather, but the battery was a little weak too and wouldnt turn it over fast enough until I put the boost box on it. It had...
I did all the research I could find on this tractor before i bought it and hope I made a good decision.The tractor starts fine so far. Not a big deal for a tractor but the fiberglass body work is very poorly finished. My question is what to check or do before i put it to work. I notice some of...