Tab Content
prs's Activity
About Me
Tab Content
  • prs's Avatar
    Yesterday, 10:10 PM
    I could find nothing wrong to explain why one side of my implements is lifted before the other. I placed a level on the floor and bubble is centered....
    7 replies | 259 view(s)
  • prs's Avatar
    07-28-2015, 10:22 PM
    Weather permitting, I will check the lift frame tomorrow as Jack described. Might even try getting a pic of the uneven lift before removing the...
    7 replies | 259 view(s)
  • prs's Avatar
    07-27-2015, 10:59 PM
    I think the lift arms may be put together crooked. Its been that way from the get-go. The left arm rest did interfere with the AUX lever going...
    7 replies | 259 view(s)
  • prs's Avatar
    07-27-2015, 10:35 PM
    Jack, how about a really dumb question? With tires equally inflated, parked on level pad and implement off, would it be best to have lift arms in...
    7 replies | 259 view(s)
  • prs's Avatar
    07-27-2015, 01:12 PM
    I want to thank all you folks for helping me along. THANKS! I have posted about a lot of issues: The "squeak"? No big deal, just greased the...
    7 replies | 259 view(s)
  • prs's Avatar
    07-23-2015, 11:43 AM
    prs replied to a thread OSHA at work? in Safety
    Those big plastic collars y'all have on your PTO shafts; I thought they wuz jest packaging and I always throw them over the creek bank. Should I...
    17 replies | 1091 view(s)
  • prs's Avatar
    07-20-2015, 09:40 PM
    Had the same model for years. Good mower. prs
    6 replies | 265 view(s)
  • prs's Avatar
    07-20-2015, 08:23 PM
    prs replied to a thread a sharp chain! in Chainsaws
    A sharp chain is easier on the saw, easier on the gas, and easier on the operator. I did not use to worry so much about that last factor, but age...
    43 replies | 1921 view(s)
  • prs's Avatar
    07-20-2015, 08:16 PM
    prs replied to a thread a sharp chain! in Chainsaws
    Interesting. I guess its just the way I was taught as a young'n. Three chains worn-out, get a new cog. It was my idea to go ahead and buy all...
    43 replies | 1921 view(s)
  • prs's Avatar
    07-19-2015, 11:44 AM
    I have done some old rusted motorcycle tanks by rinsing with detergent water and sand. Then "pickling" with muriatic acid and a final rinse. As a...
    27 replies | 846 view(s)
  • prs's Avatar
    07-18-2015, 10:45 PM
    prs replied to a thread The infamous Ventrac squeek. in Ventrac
    Murph, I have not had a squeak on it since then. I never did get around to ordering the aerosol product Raw Dodge recommended. I took my pressure...
    6 replies | 829 view(s)
  • prs's Avatar
    07-08-2015, 10:40 AM
    Ford took a gamble and rolled the dice. Sooner or later they will all have aluminum sheeting and plastic beds/floors. Ford's gamble is that the...
    121 replies | 6050 view(s)
  • prs's Avatar
    07-07-2015, 04:40 PM
    prs replied to a thread a sharp chain! in Chainsaws
    Sodo, a worn cog will be out of pitch with a new chain and thus cause chain stretch. One might end-up needing to remove a link in order to get the...
    43 replies | 1921 view(s)
  • prs's Avatar
    07-07-2015, 03:41 PM
    prs replied to a thread a sharp chain! in Chainsaws
    I have never used a real chain grinder. I tried one of those that are sort of like a Dremmel tool, its on a shelf somewhere around the shop. I do...
    43 replies | 1921 view(s)
  • prs's Avatar
    07-07-2015, 03:18 PM
    prs replied to a thread Tightening bar nuts in Chainsaws
    Universal torque specification: Tighten until threads begin to strip, then loosen one half turn. I was cleaning my old Super XL/AO for storage...
    9 replies | 687 view(s)
  • prs's Avatar
    07-02-2015, 06:39 PM
    prs replied to a thread JD750 MFWD in Parts/Repairs
    From where are you sourcing the parts? Always looking for sources to keep my JD on the job. 1982 model 650. Regarding prevention of such wear once...
    26 replies | 1081 view(s)
  • prs's Avatar
    07-02-2015, 08:29 AM
    prs replied to a thread Break'n da roolz............ in Ventrac
    Jack, you really were snared! Yes, getting older seems to present some disadvantages. Wiser does not help one itty bit if we are too stubborn or...
    6 replies | 617 view(s)
  • prs's Avatar
    07-01-2015, 07:59 PM
    prs replied to a thread JD750 MFWD in Parts/Repairs
    That looks like a device to me. ;-) prs
    26 replies | 1081 view(s)
  • prs's Avatar
    06-30-2015, 10:18 PM
    First the set-up for why. Its rained a lot this year. The ground is soft and my land is sloped. So, a couple of weeks ago I was mowing with 10 to...
    6 replies | 617 view(s)
  • prs's Avatar
    06-30-2015, 09:32 PM
    prs replied to a thread worse than an Easter Egg Hunt in Ventrac
    I was doing an oil change today and while waiting on the oil to drain I took another look at the zerks in the drive shaft. I do not think Harry...
    17 replies | 959 view(s)
No More Results
About prs

Basic Information

About prs
Location (City, State):
Logan, WV
Occupation:
Audiologist
What Make/Model of Tractor Do You Own?:
JD 650, Ventrac 4500Z AJ02248
Lot Size:
16.5 M/L
Type of Member:
Homeowner (11-20 acres)

Statistics


Total Posts
Total Posts
193
Posts Per Day
0.42
General Information
Last Activity
Yesterday 10:10 PM
Join Date
04-30-2014
Referrals
0
© 2014 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.