Tab Content
  • RANDYT's Avatar
    06-20-2018, 06:22 PM
    I have one of these on my atv, but they are designed for lawnmower. Amazon.com : Good Vibrations 17 Hitchin' Lawn Mower Post Ball Connector :...
    8 replies | 592 view(s)
  • RANDYT's Avatar
    06-17-2018, 03:27 PM
    RANDYT replied to a thread LT2042 issues in Cub Cadet L&G
    item 22 and 23 make up one bearing. the are a tapered roller bearing like a wheel bearing on a car. So each spindle requires 2 each of item 13...
    16 replies | 703 view(s)
  • RANDYT's Avatar
    06-16-2018, 09:09 PM
    RANDYT replied to a thread LT2042 issues in Cub Cadet L&G
    The bearings sound flat spotted, which can create a vibration when running. Had a brand new rider a few years ago that I had to replace all three...
    16 replies | 703 view(s)
  • RANDYT's Avatar
    06-16-2018, 07:57 PM
    RANDYT replied to a thread LT2042 issues in Cub Cadet L&G
    Small idler pulley sounds noisy, and would make a whining noise when running. The right spindle sounds like it could be dragging or a little rough...
    16 replies | 703 view(s)
  • RANDYT's Avatar
    06-16-2018, 04:35 PM
    RANDYT replied to a thread LT2042 issues in Cub Cadet L&G
    Belt breaking after a few uses indicates that something is going wrong. Either not installed correctly, wrong angle/cut of belt not fitting pulleys...
    16 replies | 703 view(s)
  • RANDYT's Avatar
    06-16-2018, 07:39 AM
    RANDYT replied to a thread LT2042 issues in Cub Cadet L&G
    See the bold text with your quote.
    16 replies | 703 view(s)
  • RANDYT's Avatar
    06-11-2018, 02:13 PM
    +1 on checking the motor mount bolts. It only takes about 1/8 turn to allow the engine to clunk on start up, acceleration and shutdown.
    8 replies | 593 view(s)
  • RANDYT's Avatar
    06-10-2018, 05:39 PM
    I feel for the OP. I have lost 2 sisters and a brother. Brother passed in 2015 at 63 Lost sister 12 years ago at 49. Between June and November...
    24 replies | 1834 view(s)
  • RANDYT's Avatar
    06-10-2018, 11:44 AM
    RANDYT replied to a thread Don't make it easy. in Welding
    Anything could be considered a burgler tool if the right cop wants to mess with you. heck, a credit card could be considered a burgler tool. ...
    24 replies | 2076 view(s)
  • RANDYT's Avatar
    06-10-2018, 08:05 AM
    RANDYT replied to a thread Everlast Powerarc 200ST in Welding
    I purchases a Hobart Stickmate 160i (27.4 max amp according to the book) few weeks ago and on the 220v side requires a 30 amp slow blow fuse type...
    19 replies | 1242 view(s)
  • RANDYT's Avatar
    06-08-2018, 04:05 PM
    RANDYT replied to a thread 3-Point Hitch PTO connect brush mower to JD3046R in Owning/Operating
    I too wish they would go back to the old single push pin disengagement for the pto implements, instead of trying to hold a ring to the rear while...
    15 replies | 706 view(s)
  • RANDYT's Avatar
    06-07-2018, 01:51 PM
    Sounds like it would make a good snow making machine. Steam mixed with the cold Canadian air.
    8 replies | 402 view(s)
  • RANDYT's Avatar
    06-06-2018, 12:12 PM
    RANDYT replied to a thread Looking for a new welder in Welding
    I have had a Hobart handler 140 for several years now and seems to work OK. Mostly run FCAW but do switch to Mig for special cases where I am...
    63 replies | 2764 view(s)
  • RANDYT's Avatar
    06-02-2018, 07:56 PM
    Back the clearance off slightly. You should feel some light resistance to moving the feeler gauge back and forth in the valve gap, but shouldn't...
    10 replies | 412 view(s)
  • RANDYT's Avatar
    05-29-2018, 06:12 PM
    RANDYT replied to a thread 6010 vs. 6011 in Welding
    I have read that the 6010 rods require a minimum of 80 OCV to operate properly and most inverter machines don't put out that voltage. Also they are...
    16 replies | 1005 view(s)
  • RANDYT's Avatar
    05-27-2018, 06:39 PM
    RANDYT replied to a thread Work boots in Rural Living
    Started with the 606 supersole or one similar with that sole which separated the toe after 3 weeks, and replaced under warranty, and the replacement...
    107 replies | 11957 view(s)
  • RANDYT's Avatar
    05-27-2018, 05:28 AM
    RANDYT replied to a thread Mig or stick? in Welding
    Something else that needs to be considered is what types of material are you going to be welding. Are you primarily dealing with clean shining...
    80 replies | 3722 view(s)
  • RANDYT's Avatar
    05-27-2018, 05:16 AM
    You will need to order a new head gasket. the normal gasket material that you purchased doesn't work for heads. Also valve clearances are set with...
    10 replies | 412 view(s)
  • RANDYT's Avatar
    05-26-2018, 06:24 PM
    RANDYT replied to a thread Work boots in Rural Living
    Never could get a pair of Redwings to last more than 30 days. Either the toe would separate or the heel on every pair I ever tried.
    107 replies | 11957 view(s)
No More Results
About RANDYT

Basic Information

About RANDYT
Location (City, State):
BEECHER CITY, IL
Interests:
HUNTING, FISHING
Occupation:
OUTDOOR POWER EQUIPMENT REPAIR
Real Name:
randy
What Make/Model of Tractor Do You Own?:
KIOTI DK45S
Attachments:
M346 BUSHHOG LOADER
Hours:
518
Lot Size:
70
Type of Member:
Homeowner (51-100 acres)

Signature


Elected Terrorist= Any elected official that proposes, votes for, or signed into law legislation that restricts or violates the constitutional right of law abiding citizens.

Statistics


Total Posts
Total Posts
1,263
Posts Per Day
0.28
General Information
Last Activity
Today 12:38 PM
Join Date
03-27-2006
Referrals
0
© 2018 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.