Tab Content
  • Stimw's Avatar
    Yesterday, 09:16 PM
    Stimw replied to a thread gate question in Rural Living
    I always put posts 4' deep. And I always paint a line on the post so when I put it in the hole I know I didn't knock dirt in and only be 3 1/2'....
    14 replies | 1701 view(s)
  • Stimw's Avatar
    09-20-2016, 07:11 PM
    Stimw replied to a thread Diesel Run On in Parts/Repairs
    I want to know why you are shutting it off with full throttle? With any engine you should give it a cool down period. For me it is about 5 minutes...
    6 replies | 406 view(s)
  • Stimw's Avatar
    09-19-2016, 08:58 PM
    Stimw replied to a thread Oil pan crack in Parts/Repairs
    How well it works will depend on how well you clean the area and scuff it up. Brake Clean is one of the easiest chemical cleaners to use and it does...
    8 replies | 694 view(s)
  • Stimw's Avatar
    09-19-2016, 07:13 PM
    Can you use your tractor in some way to push the pipe forward? Without some kind of assist I don't believe your plan will work. I have washed down...
    10 replies | 520 view(s)
  • Stimw's Avatar
    09-19-2016, 06:40 PM
    Stimw replied to a thread Tractor Shuts down in Parts/Repairs
    Make sure fuel tank is vented properly also. You can loosen the cap to see if it makes a difference.
    7 replies | 630 view(s)
  • Stimw's Avatar
    09-19-2016, 06:36 PM
    Stimw replied to a thread Oil pan crack in Parts/Repairs
    If the crack is accessible and the pan is still solid I would drain, clean VERY WELL, rough up the surface and seal it with epoxy. I knocked a hole...
    8 replies | 694 view(s)
  • Stimw's Avatar
    09-11-2016, 06:14 PM
    Back in the old days TV, Record Players and Radio (AM ONLY!) were put in a large cabinet. What a great idea! But then the TV usually went first and...
    7 replies | 1191 view(s)
  • Stimw's Avatar
    09-06-2016, 08:25 AM
    After letting it soak for a few days you might try getting a block of wood the same size as the piston and try driving the piston down and rocking to...
    16 replies | 1069 view(s)
  • Stimw's Avatar
    09-05-2016, 06:05 PM
    Need more info- is it hydo or mechanical? Did you drain trans? How long since sunk?
    11 replies | 1218 view(s)
  • Stimw's Avatar
    09-05-2016, 05:47 PM
    Have you changed/checked the oil for contamination- water/rust? Have you tried rocking it in a higher gear to free it up?
    16 replies | 1069 view(s)
  • Stimw's Avatar
    08-29-2016, 07:31 PM
    Stimw replied to a thread drywood termites in Rural Living
    I have been using "DEMON" or "CYPER" as it is also labeled. I bought it online from a DIY Pest Supply. The MSDS claims a 10 year residual for...
    7 replies | 461 view(s)
  • Stimw's Avatar
    08-28-2016, 06:34 PM
    Here is an option, DOT Air Brake Tubing- Velvac 1 2 Blue Nylon Air Hose Tubing Dot Approved 1 Foot Roll 4deg to 2degF | eBay It's easy to...
    109 replies | 6212 view(s)
  • Stimw's Avatar
    08-28-2016, 06:03 PM
    Here are pics of the old and new blades. They probably would have lasted another 10 years! But I am not that guy! :) It cuts like a Finnish Mower...
    16 replies | 1598 view(s)
No More Results
About Stimw

Basic Information

About Stimw
Location (City, State):
N. E. Florida
Occupation:
Self Employed

Statistics


Total Posts
Total Posts
1,663
Posts Per Day
0.40
General Information
Last Activity
Yesterday 09:17 PM
Join Date
05-06-2005
Referrals
1
© 2016 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.