Recent content by WayneAz

IT IS WORKING,,STARTED MOVE SOME TODAY..TESTED WITH A STICK AGAIN AND ALMOST FULL STILL..HAS 3 HOURS SINCE FILL UP AND STILL CANNOT BELEIVE HOW E Z IT IS ON FUEL.. THaNKS FOR ALL REPLIES AND PUT THIS IN FILE "IN CASE" FOR ANOTHER TIME..

MT225E FUEL GAUGE HAS STOPPED WORKING,,TRACTOR HAS 300 HOURS AND IS 2020 MODEL.. I HAVE CHECKED IN FUSE PANEL AND IT IS GOOD THERE.. ANY HELP OR IDEAS?? T.I.A. FOR ANY HELP..

I DID NOT KNOW THAT WHITE SCREEN CAME OUT SO EZ.. WITH THAT OUT I PUT A PEICE OF OLD SPEEDO CABLE IN AND FLEXED AT ANGLE.. IT IS ALMOST FULL.. DON'T KNOW HOW IT CAN RUN AND USE SO LITTLE FUEL,,,BUT NOT COMPLAINING AT ALL.

I WILL GO OUT AND TRY THAT STICK TRICK,,BUT I DON'T THINK IT WILL GO DOWN IN THIS TANK..THAT IS THE WAY I CHECK FUEL ON MY 1948 FORD 8N..:)..

L/S 2020 MT225HE= HI.. ANY TROUBLESHOOT TIPS ON FUEL GAUGE..I KNOW IT IS A LITTLE TANK,,LITTLE ENGINE AND IS VERY TRIFTY..BUTT- AFTER FILL AND WORK 5 OR MORE HOURS BY THE HR. METER,,THE NEEDLE SHOULD MOVE,,MINE DOES NOT.. I SEE WHERE SENDER MUST BE,,HOW TO CHECK IS WHAT I DON'T KNOW.. T.I.A. FOR...

I AM 77 AND DON'T SEE ANY REASON TO-WRESTLE,PRY,PUSH,PULL,,TRY TO LIFT AND GENERAL TYPE FIGHT WITH AN IMPLEMENT IF THERE IS A BETTER/EASIER WAY.. MY OLD 48 8N HAS ADJUSTABLE BOTH LOWER ARMS AND IS WORN AND LOOSE,,BUT STILL HARD TO HOOK UP SOMETIMES..JUST ME,,YOUR WAYS MAY DIFFER.. HAVE A GOOD...

NOT TRYING TO BE A SMART ARSE,,BUT ARE YOU SITTING ON/IN THE SEAT WHEN YOU TRY IT?? THAT IS SOMETHING I WOULD DO,,THEN THINK "OH CHIT" LATER AND IT WOULD WORK..

JUST A LATE AFTERTHOUGHT AND ADVICE.. MEASURE ALL YOUR IMPLEMENTS FOR THE 27 & 1/8 OR WHATEVER BETWEEN LOWER PINS..I HAVE 6 IMPS AND ONLY ONE WOULD WORK WITH QUICK HITCH,,,SO PAT'S EASY IS THE RIGHT ONE,, THANKS TO ALL AGIN FOR REPLIES..

THANK YOU ALL FOR IDEAS AND REPLIES.. I AM LOOKING INTO AND MEASURING FOR A QUICK HITCH TYPE MOD..

Hello.. we have a 2020 mt225 and changing implements just seems way too difficult.Have had an old 8n for years and it is much easier to change between imps than this is.. All has to be very/very exact to get changed from one to another..All is level-tractor and implement and sway bars loose.. I...

PUT THE PHD ON TODAY,,A REAL P.I.A... I AM SURE I DID NOT DO IT IN THE CORRECT ORDER,,BUT I DID MOST STEPS TWICE,AT LEAST..THE BALLS IN THE QUICK COUPLER WERE KINDA STUCK,,SO WAS A REAL WRESTLIN MATCH TO GET THE PTO SHAFT ON..ONCE ON IT WORKS JUST FINE.. HAPPY WITH IT..

I ORDERED A HORN SWITCH TODAY THAT "SHOULD" FIT IN THE DASH OF THE 20 MT225HE I HAVE BEEN TRYING TO PUT A HORN ON.. IF IT FITS GOOD I WILL PUT THE INFO ON IF SOMEONE WANTS IT..FROM INFO FROM JCoastie...

HELP PLZ.. WE HAVE AN MT225HE BOUGHT NEW IN JULY 2020,,ASSUME IT IS A 2020.. READ ARTICLE BY RBSTERN FROM JULY 2019 ABOUT ADDING A HORN.. GOT THE RECCOMENDED SWITCH//BOSCH RELAY AND HARNESS AND FUSE AND HOLDER.. READY TO INSTALL,,REMOVED RECTANGLE ON DASH AND SWITCH IS A LITTLE SHORT AND...

Removed the top ROPS..Big oops..Don't do that..Difficult for ol geezer to get back on..:);):rolleyes: