Recent content by zkubota

Not sure where to post this..but. I want to buy this as a concentrate to mix in my 30gal ATV sprayer, where can I find it? Thanks Zac

Excuse my ignorance, but how do I find a dealer to get parts for my Long rotary tiller? Thanks in advance Zac

Just got a 16' flatbed to haul my L4400 around to some of our rent houses. How and where should I tie it down. Chains? Straps? Thru FEL? Over Tranny? Thanks!

Just picked up a used tiller down the road. All I can make out on it is it's a Long Model 1542 6' maybe 6'6"...here's my problem: 1) I don't know much about working on tillers!! 2) Tines turn fine, but as soon as they hit the ground they quit turning and make some ugly sounds. 3) Where to find a...

Okay, I've done a search, but not an easy topic to search it seems. I'm wanting to build a ramp that will allow our four-wheelers and dirtbikes to cross without letting the cattle. (I know, lazy eh!) I'm thinking off just building a dirt ramp on the non-cattle side then a pipe ramp on the...

Wanting to get a disc for my L4400. I'm thinking 6 to 9'. I know weight is a concern, but what variations on a disc are there? different type edges, different stagger?...or are they all the same. BTW: I'll just be keeping my MX track disced up. Any resources for finding one used in Arkansas?

Dad is wanting to put a backhoe on the aforementioned tractor. The dealer recommended the 750H (was 765H). What can anyone tell us about this combination. It will not be used to dig ponds, canyons, etc, nor will it be used daily. Maybe once a month. Mostly to clean out ditch lines, dig/repair...

After reading many posts here and much contemplation. I bought an SE6 cutter this weekend. Very pleased so far. I looked at the KK and quite frankly was afraid I would be repair and replacing more than cutting. My kubota dealer priced me on a TW model cutter and a squeler model..both too high...

6 or 7\' brush-hog on an L4400 I used my father-in-laws 5' brush hog last year, but just to time consuming. do you think a 7' is to much for that tractor? Thanks

tried a search but not really sure how to describe what I'm looking for. Basically my father-in-law is wanting me to make him a drawbar with a ball mounted on one side of the square tubing, then a 2" receiver on the next side, then a 2 1/4" ball on the next side..etc, etc...you get the drift...

I\'ve never heard of using a piece of chain to..... take the place of the top link on a bush-hog. Dad says that is how he pulls his behind his Bota. Of all the farmers around us I've never seen anyone using this method. Has my father lost his mind? I have a new L4400 with an ol' 5' cutter...

Well got several hours in the saddle now. Got my blade in last week so been quite busy with my drive and track. Here are some pics, although muddy. Also are pics of my worklights. It's not as clean a look as I want for the lights, will remake my brackets soon. Only cost my $20. Got the foglight...

I had dealer make the back as wide as possible, looking at the front looks like I could sway them from left to right and be a little wider up there as well? Is this correct? I didn't see anything in the manual regarding this? May need to read thru it again.

Well, Kubota approved me, now I'm just waiting on the loader. L4400 with FEL and 6' Blade. Can't wait to get this thing home and get it dirty(then wash it ) Anyone out there got one yet, how do you like it?

Getting pretty close to buying, but concerned the L4400 is more than I need. Maybe I should re-phrase; concerned the L4400 is more expensive than what I need. (with FEL) Brush-hogging--6-10 acres--6 to 8 times a year(mostly on hillside) Dirt-work--I have a moto track for me and the kids that...