Preventing tractor back flip

   / Preventing tractor back flip #1  

retiredmgn

Gold Member
Joined
May 8, 2010
Messages
454
I was having a discussion with a friend.
Situation - a chain is attached from the bottom drawbar (several inches below the center of rotation) to an immovable object.
My contention is the front wheels are being driven into the ground. Hence, no wheelie. He says it will still wheelie the same as having the pull point several inches above the center of rotation.
Pull above the center of rotation is a no-brainer -you're going over.
Who's right?
 
   / Preventing tractor back flip #2  
It will still flip over :(

It will just be more of a sling-shot flipover :( :(

You're right, initially the front wheels will be driven into the ground, but then given enough rear wheel traction, something has to give. That something is the front end switching from being jammed into the ground to being sling shot (slung shot?) upward, & over.
 
   / Preventing tractor back flip #3  
As long as the attachment is below the "center of rotation" as you said... no wheelie !

The only way I can think to produce a wheelie is slack in the chain and popping the clutch. Then torque is greater than tractor's inertia and it rotates.... until the chain pulls the tractor back down
 
   / Preventing tractor back flip #4  
Prove it to yourself and buddy.

Draw a tractor on paper... graph the forces acting on the wheel and tractor drawbar.
 
   / Preventing tractor back flip #5  
I thought I could find a video example of an actual flip, but can't so far. However, check this tractor pull video out; Note that the tractor is pulling a wheelie the whole time. Certainly they pull from below the center of rotation, yet still get the front wheels off the ground: ‪NTPA Tractor Pull - Jefferson City, MO‬‏ - YouTube
 
   / Preventing tractor back flip #6  
Preventing tractor back flip

I have seen roller guides welded at strategic locations under tractors that allow the operator to pull from the front with the cable/chain/strap connected to the drawbar and run to the front of the tractor, so they pull using reverse.
 
   / Preventing tractor back flip
  • Thread Starter
#7  
It will still flip over :(

It will just be more of a sling-shot flipover :( :(

You're right, initially the front wheels will be driven into the ground, but then given enough rear wheel traction, something has to give. That something is the front end switching from being jammed into the ground to being sling shot (slung shot?) upward, & over.

I can't get a visual of this in my head. Logically it just don't work.
 
   / Preventing tractor back flip
  • Thread Starter
#8  
Prove it to yourself and buddy.

Draw a tractor on paper... graph the forces acting on the wheel and tractor drawbar.

That's what I did to try to convince him I was right. Draw a circle with a dot in the middle. An arrow on the circumference showing counter clockwise rotation. A line from below the dot heading right.
Seems obvious to me but he is a stubborn old coot and refused my logic.
 
Last edited:

Tractor & Equipment Auctions

2013 John Deere 824K (A51039)
2013 John Deere...
2015 INTERNATIONAL 4300 26 FT NON CDL BOX TRUCK (A51219)
2015 INTERNATIONAL...
ALL ITEMS NOT PICKED UP IN 30 DAYS WILL BE RESOLD FOR STORAGE!! (A50775)
ALL ITEMS NOT...
2019 Doosan DX225LC-5 Excavator (RIDE AND DRIVE) (VERY NICE) (A50774)
2019 Doosan...
2015 PETERBILT CLASS 8 CEMENT MIXER TRUCK (A51243)
2015 PETERBILT...
2025 Kivel 48in Forks and Frame Skid Steer Attachment (A50322)
2025 Kivel 48in...
 
Top