Page 1 of 2 12 LastLast
Results 1 to 10 of 19
  1. #1
    New Member
    Join Date
    Jun 2009
    Posts
    3

    Default Belarus 250AS

    It's my first post so be gentle. My problem is I drove my tractor around the yard and went to park it in the back yard. The throttle lever would not shut the engine off so I placed the tranny in high gear with the rpms very low I let out on the clutch and it died. I left it sitting there for a few weeks and it got rained on. I went to move the tractor and now it will run fine but will not move. The gears grind a little but it feels like it shifts into gear. But when I let out on clutch it acts like it is in neutral. You can push the tractor around and it does not act like it is in gear at all. I pulled the clutch inspection plate off and there was water collected in the bottom of the housing but everything appeared to be fine. I put a shot of grease in the fitting. Any ideas? The clutch never gave me a minutes trouble. Always shifted smooth until now. The PTO shaft engages but does not keep turning when the clutch is pressed. " I am not sure if it ever did since I have not had the tractor too long from my grandfather". Any help would be greatly appreciated. Also would pulling the starter give me any view of the clutch?

    Thanks,

    Andy

  2. #2
    New Member
    Join Date
    Jun 2009
    Posts
    3

    Default Re: Belarus 250AS

    correction. The pto shaft does not stop or slow down when the clutch is pressed.

  3. #3
    New Member
    Join Date
    Jun 2009
    Posts
    3

    Default Re: Belarus 250AS

    Somebody please take a stab at my problem if you can. I don't want to take my tractor in half and find out I could have avoided it.

    Thanks

  4. #4
    Epic Contributor Bird's Avatar
    Join Date
    Mar 2000
    Posts
    39,585
    Location
    Texas

    Default Re: Belarus 250AS

    There's just not too many Belarus owners around. Of course it sounds as if your clutch is gone, but I'm sure not enough mechanic, especially on Belarus, to give you any reliable information.
    Bird

  5. #5
    Bronze Member nike's Avatar
    Join Date
    Feb 2011
    Posts
    93
    Location
    Ontraio
    Tractor
    Belarus 255

    Default Re: Belarus 250AS

    I have checked the manuals, every thing leads to clutch needing replaced. You may want to check out the linkages...good luck.

  6. #6
    Platinum Member
    Join Date
    Oct 2010
    Posts
    687
    Location
    Near Peace river -Alberta
    Tractor
    ASV 4810

    Default Re: Belarus 250AS

    By the sound of it you jinxed the clutch plate when you killed the engine.
    You'll need to split the tractor to get access.
    The PTO is either on its own clutch or splined directly in the flywheel.
    3 cockshutt 1855,1 cockshutt 1800.
    Belarus 800 and 925 .AC 940 whl ldr.Waldon 500 whl ldr.
    ASV 4810 tracksteer.
    4 GMC 2500 6.5/6.2 diesel trucks

  7. #7
    New Member
    Join Date
    Feb 2012
    Posts
    1
    Location
    Picayune Mississippi
    Tractor
    1983 Belarus 250AS

    Default Re: Belarus 250AS

    I did have that problem once when I first bought my 250AS. I had the HI LO shift in the center position and the tractor would not move. I'm old and was worried I might do it again so I put a bolt in the shift cover so it could NOT be put in HI. I have done a lot of work to my tractor. I installed new clutch, new throw out bearing , new hydraulic drive gear bearings and seals. Replaced all the seals and O rings in the hydraulic cylinder, control valve and I replaced the brake bands. I found the Manual is not very good at explaining the repair procedures you just have to take your time. I actually bought two clutches as while I was replacing the first one I got it in a bind and broke it. I just painted the tractor and am replacing the seat at this time.

  8. #8
    New Member
    Join Date
    Mar 2013
    Posts
    7
    Location
    hamilton,alabama
    Tractor
    belarus,250as

    Default Re: Belarus 250AS

    does-anyone-have-or-know-where-to-find-a-video-or-picture-breakdownof-250as-howto-manual

  9. #9
    New Member
    Join Date
    Mar 2013
    Posts
    7
    Location
    hamilton,alabama
    Tractor
    belarus,250as

    Default Re: Belarus 250AS

    check-under-rightside-floorboard----look-for-a-lever-with-knob----there-are-two-or-three-positions------this-is-cold-start-lever--this-lever-may-be-in-wrong-slot.----but-sometimes-highlow-shift-lever-by-main-shifter-is-hard-to-get-back-in-geer.this-is-caused-by-week-forks-inside-tranny

  10. #10
    Elite Member
    Join Date
    Mar 2002
    Posts
    2,891
    Location
    Iuka Mississippi USA
    Tractor
    3550 Fard Backhoe and a 1948 Farmall Cub,

    Default Re: Belarus 250AS

    I think theres a clear copy of them at Jensales website. I have a friend that had a 240 for many years but sold it. Ill ask if he has his manual. You dont happen to know Danny or Johnny Ray from Hamilton do you.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
© 2016 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.