Page 37 of 76 FirstFirst ... 273435363738394047 ... LastLast
Results 361 to 370 of 751
  1. #361
    New Member
    Join Date
    Jul 2012
    Posts
    1
    Location
    Provo, UT
    Tractor
    JD X300R

    Default Re: TuffTorq K46 Repair Guide with Pictures

    joebob

    How about a less cryptic description of what needs to be machined and what is causing the problem. I'm not a schooled mechanic and can't quite understand what you are saying. Your descriptions sound impressive but can you put it in 5th grade language.

    Thanks,
    Chris

  2. #362
    New Member
    Join Date
    Aug 2012
    Posts
    3
    Location
    Silsand
    Tractor
    Husqvarna

    Default Re: TuffTorq K46 Repair Guide with Pictures

    Quote Originally Posted by pcm3pcm3 View Post
    joebob

    How about a less cryptic description of what needs to be machined and what is causing the problem. I'm not a schooled mechanic and can't quite understand what you are saying. Your descriptions sound impressive but can you put it in 5th grade language.

    Thanks,
    Chris
    I'm sorry. I replaced the propeller shaft. I put all the parts as shown on the diagram and refilled it with oil, started up and should drive forwards. The tracktor vent reversing. I tried to go revers and the tracktor goes forvards.
    Is there any valves in the case that can be installed wrong??

  3. #363
    Bronze Member RBLapham's Avatar
    Join Date
    Apr 2011
    Posts
    78
    Location
    Tennessee
    Tractor
    John Deere X300

    Default Re: TuffTorq K46 Repair Guide with Pictures

    Quote Originally Posted by Theodorsen View Post
    I'm sorry. I replaced the propeller shaft. I put all the parts as shown on the diagram and refilled it with oil, started up and should drive forwards. The tracktor vent reversing. I tried to go revers and the tracktor goes forvards.
    Is there any valves in the case that can be installed wrong??
    See post # 347 thru 350 in this thread - you have the wedge in backwards - it goes in differently depending on your tractor brand/linkage. Also see post 19 for picture of the wedge.
    Deere X300, Plug aerator with winch

  4. #364
    New Member
    Join Date
    Aug 2012
    Posts
    3
    Location
    Silsand
    Tractor
    Husqvarna

    Default Re: TuffTorq K46 Repair Guide with Pictures

    Thanks. I looked at the parts diagram for this piece and this part was turned 180 degrees from the pic i #4.
    Then i have to do the work again.

    Thank you so much for the answer. This wa the only part that i not was shure on. (exept the smale valves at the pump.)

  5. #365
    New Member
    Join Date
    Aug 2012
    Posts
    1
    Location
    Newbury UK
    Tractor
    Simplicity Baron

    Default Re: TuffTorq K46 / John Deere L110 Transmission Repair Guide with Pictures

    I have all the classic symptoms on my Simplicity Baron's K46Q - slows to a standstill when hot - spotted this excellent thread and thought i would have a go at a repair. So being in the uk I contacted the uk importer for TuffTorq and have been quoted 450 ($700 us) for a repair kit +post and packing. Does anyone else have any experience of doing this in uk or europe? There must be a better price for this.

    Thanks

  6. #366
    New Member
    Join Date
    Aug 2012
    Posts
    18
    Location
    Boise, ID
    Tractor
    2005 JD L118

    Default Re: TuffTorq K46 Repair Guide with Pictures

    Quote Originally Posted by pcm3pcm3 View Post
    joebob

    How about a less cryptic description of what needs to be machined and what is causing the problem. I'm not a schooled mechanic and can't quite understand what you are saying. Your descriptions sound impressive but can you put it in 5th grade language.

    Thanks,
    Chris
    I second the request. Joebob, could you either attach pictures showing the surfaces to be ground, or use the TT K46 explosion drawings and highlight the surfaces? Your descriptions of what all you ground are too vague. I think many others go the route of buying all the replacement parts because the surfacing grinding approach is not so clear.

  7. #367
    New Member
    Join Date
    Aug 2012
    Posts
    1
    Location
    Boxford MA
    Tractor
    John Deere L130

    Default Re: TuffTorq K46 Repair Guide with Pictures

    Can you please post a link to the purging instructions.

    Thanks

  8. #368
    Bronze Member RBLapham's Avatar
    Join Date
    Apr 2011
    Posts
    78
    Location
    Tennessee
    Tractor
    John Deere X300

    Default Re: TuffTorq K46 Repair Guide with Pictures

    Quote Originally Posted by roosterly9 View Post
    Can you please post a link to the purging instructions.

    Thanks
    See post #7 on the first page - everything in in this thread someplace
    Deere X300, Plug aerator with winch

  9. #369
    Bronze Member
    Join Date
    Nov 2002
    Posts
    54
    Location
    Manchester MI.
    Tractor
    Case 530CK

    Default Re: TuffTorq K46 Repair Guide with Pictures

    Hi Guys;
    Look in my other posts for the method I used. Let me Know if you need further info.
    Cheers
    Joebob

  10. #370
    Bronze Member
    Join Date
    Nov 2002
    Posts
    54
    Location
    Manchester MI.
    Tractor
    Case 530CK

    Default Re: TuffTorq K46 Repair Guide with Pictures

    On the block, I ground the surface of the 2 faces where the motor & pump cylinders revolve. You may have to grind the faces of the cylinders also if needed. The surfaces have a number of slotted holes that fluid passes in. In betw. these holes can have very slight scoring, allowing oil to leak past where it's supposed to go. Don't have any piccies, it's back together.Hope this helps, let me know.
    Cheers
    Joebob

Page 37 of 76 FirstFirst ... 273435363738394047 ... LastLast

Similar Threads

  1. Replies: 13
    Last Post: 05-31-2009, 08:50 AM
  2. JD Owning/Operating FAQ (Please Help)
    By Muhammad in forum John Deere Owning/Operating
    Replies: 42
    Last Post: 02-08-2009, 10:38 PM
  3. cub cadet panel repair
    By harleyizy in forum Parts/Repairs
    Replies: 8
    Last Post: 12-12-2008, 12:49 AM
  4. Pictures, Pictures
    By ddl in forum News/Feedback
    Replies: 9
    Last Post: 11-17-2001, 08:35 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
© 2013 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.