Results 1 to 7 of 7
-
07-03-2012, 06:55 PM #1New Member
- Join Date
- Jul 2012
- Posts
- 6
- Location
- Dartmouth NS
- Tractor
- JD 2520
JD 2520 Wiring schematics
Just ordered a tech manual from JD to get a wiring diagram ( start/fuel circuits ) - but does anyone here have one for a JD 2520?
Parts Department only has harness descriptions, service department was too busy (and slightly under pressure for others) to track it down, so off to a full blown tech manual to trace out a probable short.
Help
porters_lake@hotmail.com
-
07-03-2012, 08:15 PM #2
Re: JD 2520 Wiring schematics
I have the CD. What exactly are you after?but does anyone here have one for a JD 2520?
Greg2009 2520
FEL/61" HD bucket/replaceable cutting edge
62D2 MMM
IMatch Quick Hitch
Homemade 3PT Receiver
Homemade Ballast Box
Woods GB65 Box Blade
A "REAL" snow blade --- JD 380A
90% Restored 1987 JD 316
MY BALLAST BOX:
http://www.tractorbynet.com/forums/b...box-build.html
MY SE SEAT 2520 MOD:
http://www.tractorbynet.com/forums/j...my-2520-a.html
-
07-03-2012, 08:22 PM #3New Member
- Join Date
- Jul 2012
- Posts
- 6
- Location
- Dartmouth NS
- Tractor
- JD 2520
Re: JD 2520 Wiring schematics
Greg
Thanks for the reply - looking for the start / run circuits - having a problem with the selonoid on the injector pump. Do not seem to have a "run" circuit being energized, but have all the feeds from the switch looking good. Not sure if the schematic shows up in "Fuel" or "General".
Your help would be really appreciated.
Porters
Porters_lake@hotmail.com
-
07-03-2012, 08:57 PM #4New Member
- Join Date
- Jul 2012
- Posts
- 6
- Location
- Dartmouth NS
- Tractor
- JD 2520
Re: JD 2520 Wiring schematics
The selonoid on the pump/injector has what appears to be two feeds - start and run - start works fine, ,,, when you let the key go to run - it dies,,, - looks like a circuit is broken (RED Lead) - It appears that the Red circuit is being powered from a "Run" - ALL Are ASSUMUMPTIONS - Do you're wiring diagrams agree?...
Still betting this is an electrical prob.
Porters
-
07-03-2012, 09:24 PM #5
Re: JD 2520 Wiring schematics
Your solenoid has two coils in it. One is for a pull-in function (start), and the other is a hold-in function (run). Have you checked that both coils have continuity to ground? The hold-in coil gets a lot of hours on it and it wouldn't be unusual for it to open up.
The other check is to see if you have voltage applied to the red lead with the key on and an operator in the seat.JD 790 w/70 FEL & 7 BH on turf tires
JD 455 w/60" MMM & 54" front blade
-
07-03-2012, 09:56 PM #6
Re: JD 2520 Wiring schematics
There are quite a few fuel schematics. Have you tried what K7 suggested? I wanted to post the explanation of the fuel start circuit,but being this is a JD manual,of course I can't show you any of the textNot sure if the schematic shows up in "Fuel" or "General".
I feel you may just have to wait until you get yours.
Greg2009 2520
FEL/61" HD bucket/replaceable cutting edge
62D2 MMM
IMatch Quick Hitch
Homemade 3PT Receiver
Homemade Ballast Box
Woods GB65 Box Blade
A "REAL" snow blade --- JD 380A
90% Restored 1987 JD 316
MY BALLAST BOX:
http://www.tractorbynet.com/forums/b...box-build.html
MY SE SEAT 2520 MOD:
http://www.tractorbynet.com/forums/j...my-2520-a.html
-
05-16-2013, 10:23 AM #7New Member
- Join Date
- May 2013
- Posts
- 1
- Location
- Boley, OK
- Tractor
- JD 2520
Re: JD 2520 Wiring schematics
I need a wiring diagram for an old JD 2520 tractor
Similar Threads
-
3316 wiring schematics
By cruit15 in forum Mahindra Owning/OperatingReplies: 8Last Post: 01-16-2012, 08:04 PM -
Wiring Schematics for Belarus 825?
By Austia001 in forum All Other BrandsReplies: 7Last Post: 10-14-2011, 10:28 AM -
2520-Eletrical wiring behind the seat
By megaboz in forum John Deere Buying/PricingReplies: 2Last Post: 05-24-2011, 04:28 PM -
Hydraulic Schematics
By Surgeon in forum Massey Ferguson Owning/OperatingReplies: 0Last Post: 10-26-2008, 10:22 PM -
hydraulic schematics
By hbarski in forum CustomizationReplies: 26Last Post: 02-15-2006, 10:24 AM


Reply With Quote

