Results 1 to 6 of 6
  1. #1
    New Member
    Join Date
    Dec 2012
    Posts
    4
    Location
    Sumter, SC
    Tractor
    Ford 1910

    Default Ford 1910 Clutch Alignment Tool

    Hello Everyone,

    I have run into a little problem. I have split my tractor for an engine rebuild and now have to rejoin my tractor and I can't find a clutch alignment tool. The tool steps are; 15/16" 13 Spline and 1 3/8" 19 Spline. This is a dual action clutch and I just can't find the tool anywhere. Can anyone help me in my search, or perhaps some guidance on making my two halves whole again? My tractor is a 1984 Ford 1910. The clutch is the same as the Ford 2110 and was manufactured by Shibaura in Japan. It is also compatible with several Shibaura tractors. Any help would be greatly appreciated.

    Thanks in advance,

    Darrell
    Lucky1910
    Last edited by Lucky1910; 12-31-2012 at 08:34 PM. Reason: Typo: changed 1 3/8" 29 spline to 1 3/8" 19 spline

  2. #2
    Veteran Member jimmysisson's Avatar
    Join Date
    Jul 2005
    Posts
    1,755
    Location
    W.Mass
    Tractor
    1993 NH 2120 (the best), 1974 MF 135 (sold, but solid), 1947 Farmall A (bought, sold, bought back, sold again), 1956 MH50 lbt (sold, in 1980, darn it)

    Default

    Guys have been known to turn a tool like that on a wood lathe. If you know the dimensions for a snug-not-tight fit you can make one in an hour or less.
    Jim
    "Anything worth doing is worth doing slowly" Mae West

  3. #3
    New Member
    Join Date
    Dec 2012
    Posts
    4
    Location
    Sumter, SC
    Tractor
    Ford 1910

    Default Re: Ford 1910 Clutch Alignment Tool

    Quote Originally Posted by jimmysisson View Post
    Guys have been known to turn a tool like that on a wood lathe. If you know the dimensions for a snug-not-tight fit you can make one in an hour or less.
    Jim
    Thanks Jim. I do happen to be a bit of a carpenter, and I do own a lathe, so I guess I will give it a shot. I tried to eyeball it, but I never could get it all the into the housing, hopefully this will do the job. Great tip.

    Darrell

  4. #4
    New Member
    Join Date
    Jan 2015
    Posts
    1
    Location
    Ga.
    Tractor
    Ford 1910

    Default Re: Ford 1910 Clutch Alignment Tool

    Lucky1910 if I could make one I would not be asking

  5. #5
    Gold Member Raw Dodge's Avatar
    Join Date
    Apr 2009
    Posts
    412
    Location
    Orange County,NY
    Tractor
    Ventrac 4231,Dixie Chopper XXWD5000

    Default

    I had the same problem when I put a new clutch in my 1910 a few months ago....honestly i eyeballed it up before tightening the clutch basket,used a fee feeler guages and screwdriver to double check I was centered and it went right together....as I was drawing the tractor back together I used a simple 1000 pound rated ratcheting tiedown to pull the front and back together because I had no help I slowly turned the engine over and drew it together I engaged the PTO and put a large pipe wrench on it to keep the transmission and PTO input shaft for moving so I can line them up.again I was alone if I had help it would've went a lot faster
    Cat 246 SS,Homemade 35T log splitter,2004 Ventrac 4231G various attachments...2005 Dixie chopper XXWD5000, 2001 Dixie Chopper XW2500-60

  6. #6
    Veteran Member Kernopelli's Avatar
    Join Date
    Oct 2006
    Posts
    1,752
    Location
    Carterville, Illinois
    Tractor
    Mitsubishi MTE2000D, Dig It 258 Backhoe

    Default Re: Ford 1910 Clutch Alignment Tool

    I have never owned an alignment tool. I either turn a wood dowel down to the correct steps in diameter or use a dowel that is already the diameter of the small end and wrap tape around the dowel to make the second larger step. Either way has worked perfectly.
    Darryl

Similar Threads

  1. Ford 1910 Clutch Pedal Problem
    By claimsman in forum New Holland Owning/Operating
    Replies: 9
    Last Post: 07-21-2013, 07:20 PM
  2. Ford 861 Clutch Setup Tool
    By 74superb in forum Parts/Repairs
    Replies: 0
    Last Post: 01-04-2012, 06:35 PM
  3. Ford 1910 sticking pto clutch
    By Cpro in forum New Holland Owning/Operating
    Replies: 6
    Last Post: 08-12-2011, 07:32 PM
  4. ford 1910 clutch problems
    By pete581 in forum Parts/Repairs
    Replies: 3
    Last Post: 11-27-2010, 11:23 AM
  5. Ford 1910 PTO Clutch Issues
    By pinotfilmnoir in forum New Holland Owning/Operating
    Replies: 8
    Last Post: 09-27-2009, 06:44 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
© 2014 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.