Results 1 to 10 of 10
  1. #1
    Bronze Member ROYCEWILLARDOKLAHOMA's Avatar
    Join Date
    May 2012
    Posts
    68
    Location
    Milburn Oklahoma
    Tractor
    MX 5100 KUBOTA 2012/

    Default john deere disc 105 6 foot disc, looking for parts

    the disc blades on the front left bar are all loose and wobble around, Im hunting parts-1_0214131621a_259476-jpg
    Willardskillard

  2. #2
    Advertiser sweettractors's Avatar
    Join Date
    Jul 2003
    Posts
    7,150
    Location
    Central Kentucky
    Tractor
    JD 6403 CHA-JD 3130 CHA

    Default Re: john deere disc 105 6 foot disc, looking for parts

    Quote Originally Posted by ROYCEWILLARDOKLAHOMA View Post
    the disc blades on the front left bar are all loose and wobble around, Im hunting parts-1_0214131621a_259476-jpg
    That looks like a standard flange bearing available at most hardware stores. You need to disassemble to determine axle size and condition of the axles. Ken Sweet
    http://www.sweetfarms.com/

    Sweet Farm Equipment LLC (Internet Sales, Shipping All States)
    Shipping Facility
    1815 Defries Rd., Canmer, Ky 42722 Toll Free 1-866-528-3323
    Ken Sweet sweet@scrtc.com

    Shipping Example: Can ship 800 lbs from Ky. to Dallas for $165
    The Northeast shipping corridor is a little more expensive.

  3. #3
    Bronze Member ROYCEWILLARDOKLAHOMA's Avatar
    Join Date
    May 2012
    Posts
    68
    Location
    Milburn Oklahoma
    Tractor
    MX 5100 KUBOTA 2012/

    Default Re: john deere disc 105 6 foot disc, looking for parts

    -2013-03-11_11-00-29_783-a
    Quote Originally Posted by sweettractors View Post
    That looks like a standard flange bearing available at most hardware stores. You need to disassemble to determine axle size and condition of the axles. Ken Sweet
    Thank you man, I'm posting some more pictures. I have it off tractor now. all the others are tight. its just the one bar with problems. Looks like somebody replaced some parts and didnt get it back together tight. ill have the pics up soon now if you will take a look at them for me. Thanks again. And Im looking for a good place to start ordering part from.-1_0214131621a_259476-jpg-1_0214131621a_259476-jpg-2013-03-11_11-00-23_642-a
    Last edited by ROYCEWILLARDOKLAHOMA; 03-11-2013 at 12:49 PM. Reason: adding picture
    Willardskillard

  4. #4
    Elite Member blueriver's Avatar
    Join Date
    Oct 2007
    Posts
    4,370
    Location
    S.E.Oklahoma
    Tractor
    JD 5520 Montana 4340 Farmall Super C

    Default Re: john deere disc 105 6 foot disc, looking for parts

    TSC Durant has those flange bearings in stock (well most of the time) ... just as Ken said know the size of the axle as well as the condition. Some folks like grease less ones ... I like the flanges with the grease zerk.

    Also Pettit Machinery Durant ... if not they can get them!!!
    "When selling a lifetime ... don't sell it short"
    auctioneer@southernauctionco.com

  5. #5
    Elite Member blueriver's Avatar
    Join Date
    Oct 2007
    Posts
    4,370
    Location
    S.E.Oklahoma
    Tractor
    JD 5520 Montana 4340 Farmall Super C

    Default Re: john deere disc 105 6 foot disc, looking for parts

    Also ... start soaking that axle nut with penetrating oil get a couple good sized pipe wrenches as well as a length of pipe ... sometimes the axle nut may even need heat to get it broke loose.
    "When selling a lifetime ... don't sell it short"
    auctioneer@southernauctionco.com

  6. #6
    Bronze Member ROYCEWILLARDOKLAHOMA's Avatar
    Join Date
    May 2012
    Posts
    68
    Location
    Milburn Oklahoma
    Tractor
    MX 5100 KUBOTA 2012/

    Default Re: john deere disc 105 6 foot disc, looking for parts

    Quote Originally Posted by blueriver View Post
    Also ... start soaking that axle nut with penetrating oil get a couple good sized pipe wrenches as well as a length of pipe ... sometimes the axle nut may even need heat to get it broke loose.
    Thanks man, I got it fixed. When you were naming those places around durant It surprised me, Then I saw your screen name Blueriver and realized you were local, when you said TSC company did you mean Tractor supply? what looked like the problem was somebody kept using it after bearing went out and ate the shaft up some what and damaged the threads where the nut went on the end of the bolt. When they went back with new parts they could not tighten it all the way because of the threads, so all these parts were had slack between them. I went to tractor supply and bought a 36'' by 1'' inch all thread washers, nuts, and lock washers. On the inside end that I couldn't get a wrench of any size on because it fits flush with the end cap which the whole thing spins when you try to take nut off, I put 2 nuts and tacked them with a 7018 then started sliding all the parts on the way they go, then a big washer-and lock washer and nut with some anti seize on it. Next time I will be able to get a crescent on both ends, or crescent and a impact. Everything is back tight. I was worried if the all thread was strong enough? When leaving TSC I swung out by the implements and noticed all the new discs have all thread gang bolts.
    Willardskillard

  7. #7
    Elite Member blueriver's Avatar
    Join Date
    Oct 2007
    Posts
    4,370
    Location
    S.E.Oklahoma
    Tractor
    JD 5520 Montana 4340 Farmall Super C

    Default Re: john deere disc 105 6 foot disc, looking for parts

    Did you use the all thread as the axle? (The shaft that all the disc and disc spacers go on) ... I hope I read that wrong. The main shaft is a square axle and the disc have a square center to match the axle so they won't spin on the shaft.
    "When selling a lifetime ... don't sell it short"
    auctioneer@southernauctionco.com

  8. #8
    Elite Member blueriver's Avatar
    Join Date
    Oct 2007
    Posts
    4,370
    Location
    S.E.Oklahoma
    Tractor
    JD 5520 Montana 4340 Farmall Super C

    Default Re: john deere disc 105 6 foot disc, looking for parts

    Small world ... I'm going to be in your area mid morning talking to a possible auction client. I don't think we've met ... if your an auction fan you've probably been to one or more of my auction sales.
    "When selling a lifetime ... don't sell it short"
    auctioneer@southernauctionco.com

  9. #9
    Bronze Member ROYCEWILLARDOKLAHOMA's Avatar
    Join Date
    May 2012
    Posts
    68
    Location
    Milburn Oklahoma
    Tractor
    MX 5100 KUBOTA 2012/

    Default Re: john deere disc 105 6 foot disc, looking for parts

    Quote Originally Posted by blueriver View Post
    Small world ... I'm going to be in your area mid morning talking to a possible auction client. I don't think we've met ... if your an auction fan you've probably been to one or more of my auction sales.
    Im in filmore, off of Callen Road.
    Willardskillard

  10. #10
    Bronze Member ROYCEWILLARDOKLAHOMA's Avatar
    Join Date
    May 2012
    Posts
    68
    Location
    Milburn Oklahoma
    Tractor
    MX 5100 KUBOTA 2012/

    Default Re: john deere disc 105 6 foot disc, looking for parts

    Quote Originally Posted by blueriver View Post
    Did you use the all thread as the axle? (The shaft that all the disc and disc spacers go on) ... I hope I read that wrong. The main shaft is a square axle and the disc have a square center to match the axle so they won't spin on the shaft.
    The main shaft on mine was a 1 inch by 36 inch bolt. That goes through the center of all the parts. My discs wont all be turning independently but that shouldn't be a problem in sandy regions i dont think. They will all turn as one so there will be only 2 bearings to wear out. All the new ones are like this I think, or the ones I looked at. I will know in a few hours how it works and post the results. If its as good as I think Im doing them all like this. Its a $18 fix.
    Willardskillard

Similar Threads

  1. John Deere Disc Parts for sale, KBA, RW
    By sweettractors in forum Attachments
    Replies: 11
    Last Post: 08-13-2013, 04:50 PM
  2. John Deere RWA Disc parts needed
    By N401pf in forum Parts/Repairs
    Replies: 2
    Last Post: 02-06-2013, 08:52 PM
  3. Anyone Need parts for a older John Deere disc ???
    By sweettractors in forum Parts/Repairs
    Replies: 5
    Last Post: 01-31-2013, 08:44 AM
  4. John Deere 144 Disc
    By lomarker in forum John Deere Buying/Pricing
    Replies: 0
    Last Post: 08-22-2004, 07:43 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
© 2014 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.