Results 1 to 6 of 6
-
05-13-2013, 08:17 PM #1
- Join Date
- May 2013
- Posts
- 3
- Location
- sydney nsw
- Tractor
- Ford 6600
Ford 6600 with hydraulic problem
Hi All, If anyone can help i have a Ford 6600 and i have a front blade on it. recently whilst using in the paddock i hit a bump in the field and the front blade hydraulically
will not go up anymore. The rear point linkage works perfectly. Any suggestions?
-
05-14-2013, 07:37 AM #2
- Join Date
- Jan 2007
- Posts
- 7,169
- Location
- Coyote Flats,Tx
- Tractor
- JD 4255/Kubota M7040 HDC
Re: Ford 6600 with hydraulic problem
Did you check cylinder rod for bending? Are hyd connections still attached correctly?
-
05-14-2013, 07:22 PM #3
- Join Date
- May 2013
- Posts
- 3
- Location
- sydney nsw
- Tractor
- Ford 6600
Re: Ford 6600 with hydraulic problem
Hi Jim, Thanks for your imput.I have checked both cylinder rods for bending with a small straight edge and all seemed straight and all the hydraulic connections are good.
As the front hydralics do not work i am assuming its an oring or seal of some description as the rear 3 point linkage works perfect. There is two valves on the pump one engages the front hydraulics to rear hydralics and the other one is a flow valve this valve does not let you adjust it as previuosly it seems like it semi locked up.
-
05-14-2013, 07:39 PM #4
- Join Date
- Mar 2002
- Posts
- 52,712
- Location
- Central florida
- Tractor
- ym1700, NH7610S, Ford 8N, 2N, NAA, 660, 850 x2, 541, 950, 941D, 951, 2000, 3000, 4000, 4600, 5000, 740, IH 'C' 'H', CUB, John Deere 'B', allis 'G', case VAC
Re: Ford 6600 with hydraulic problem
reseat all qd's inthe system.
if still nothing, does actuating a hyd lever cause the engine to strain? if no.. check fluid flow to that line from the valve.
-
05-15-2013, 08:44 PM #5
- Join Date
- May 2013
- Posts
- 3
- Location
- sydney nsw
- Tractor
- Ford 6600
Re: Ford 6600 with hydraulic problem
Hi when operating the lever it does nothing. No load on the motor. Its also not creeping from the position it is resting. Im out of town for a week and when back i will check that the fluid is flowing through to the hyraulics. I think that this may be the problem. Thanks for your imput
-
05-15-2013, 10:38 PM #6
Re: Ford 6600 with hydraulic problem
G'day not sure if the 6600 has the same remote setup as the older 7000, check the knob under the right side of the seat and make sure it is in the right position ( can't remember if it has to be out or in ). I had to go to a 7000 once that the FEL had stopped working and finally found this to be the cause apparently must have got knocked by the op's leg in typing this I am thinking it has to be out to work the remotes.
Jon
Similar Threads
-
Ford 6600 REPOWER 401
By 401FordManNZ in forum New Holland Owning/OperatingReplies: 1Last Post: 09-13-2012, 09:23 AM -
Ford 6600 3pt lift problem
By triniman in forum HydraulicsReplies: 10Last Post: 03-20-2012, 02:03 PM -
ford 6600
By trickyricky in forum New Holland Owning/OperatingReplies: 9Last Post: 03-05-2012, 03:04 PM -
FORD 6600 COVER
By gilberto in forum Parts/RepairsReplies: 0Last Post: 04-17-2010, 08:55 PM -
Loader ford 6600
By mastertractor in forum Owning/OperatingReplies: 3Last Post: 03-31-2010, 02:52 PM