Results 1 to 10 of 10
  1. #1
    Advertiser kennyd's Avatar
    Join Date
    Jul 2003
    Posts
    11,870
    Location
    Westminster, MD
    Tractor
    John Deere 4110, 455

    Default HYD Cylinder Rebiuld?

    I am trying to take the cylinders of my JD 410 loader apart, I have the snap ring off but cannot see what holds the rod giude in...

    Attached is the parts breakdown
    Any Thoughts???
    Attached Images Attached Images

  2. #2
    Veteran Member
    Join Date
    Mar 2004
    Posts
    2,427
    Location
    Central Ma.
    Tractor
    7275 Cub Cadet

    Default Re: HYD Cylinder Rebiuld?

    I'd love to help you out. But I can't tell from that picture. Is there an internal threaded nut below the snap ring?

  3. #3
    Advertiser kennyd's Avatar
    Join Date
    Jul 2003
    Posts
    11,870
    Location
    Westminster, MD
    Tractor
    John Deere 4110, 455

    Default Re: HYD Cylinder Rebiuld?

    No threads, The picture shows a ring, part #6, but I have no idea idea how to get to it...

  4. #4

    Join Date
    May 2004
    Posts
    5
    Location
    Canada
    Tractor
    JD 4310

    Default Re: HYD Cylinder Rebiuld?

    Hi
    Once you remove the snap ring #3 you will have to tap the # 10 guide into the barrel about 3/4 of a inch to get at the other snap ring remove ring . Then just pull rod and guide out of barrel.
    Ken

  5. #5
    Advertiser kennyd's Avatar
    Join Date
    Jul 2003
    Posts
    11,870
    Location
    Westminster, MD
    Tractor
    John Deere 4110, 455

    Default Re: HYD Cylinder Rebiuld?

    Well, That is what the service guy said at JD, but I tapped it in about 2" so far and there is no other snap ring, there is a round grove in the barrel, but no ring.
    I am at my wits end on this one...

  6. #6
    Veteran Member
    Join Date
    Mar 2004
    Posts
    2,427
    Location
    Central Ma.
    Tractor
    7275 Cub Cadet

    Default Re: HYD Cylinder Rebiuld?

    If there is no ring, Can you pull the shaft out?

  7. #7
    Advertiser kennyd's Avatar
    Join Date
    Jul 2003
    Posts
    11,870
    Location
    Westminster, MD
    Tractor
    John Deere 4110, 455

    Default Re: HYD Cylinder Rebiuld?

    Negative.
    I even tried 100 lbs. of air and no go...

    The snap ring I took off only keeps the rod guide from going in, but something has to stop it from coming out, but I cannot see an interanal ring.

    Guess I'll have to go back to JD in the morning.

  8. #8
    Advertiser kennyd's Avatar
    Join Date
    Jul 2003
    Posts
    11,870
    Location
    Westminster, MD
    Tractor
    John Deere 4110, 455

    Default Re: HYD Cylinder Rebiuld?

    I finally got them apart today, turns out there is a orange piece of plastic in the bag of new seals. You place to plastic in the groove in the barrel, it makes it smooth, then yank the rod out, the plastic lets the internal ring slide right on out.

  9. #9
    Super Member RickB's Avatar
    Join Date
    Sep 2000
    Posts
    7,590
    Location
    Eastern NY
    Tractor
    Case 885, Ford 4000

    Default Re: HYD Cylinder Rebiuld?

    That is a new one on me! Usually the ring stays in the groove as Korum described. Did you find out about the orange part by reading the kit instructions? [img]/forums/images/graemlins/grin.gif[/img] [img]/forums/images/graemlins/grin.gif[/img]

  10. #10
    Advertiser kennyd's Avatar
    Join Date
    Jul 2003
    Posts
    11,870
    Location
    Westminster, MD
    Tractor
    John Deere 4110, 455

    Default Re: HYD Cylinder Rebiuld?

    Of course, there were no instructions with the new seal kit. If there was I would not have posted the original question.

    I went to JD and talked to a mechanic.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
© 2014 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.