Search:

Type: Posts; User: SSdoxie; Keyword(s):

Results 1 to 100 of 2143
Page 1 of 22 1 2 3 4

Search: Search took 0.09 seconds.

  1. Thread: 7753 steering

    by SSdoxie
    Replies
    2
    Views
    158

    Re: 7753 steering

    Each pump and each drive motor vary somewhat in efficiency, so some degree on veering to one side is normal. Question is How Much does it veer? Rule of thumb is less than 5' to the side in 50' of...
  2. Thread: ROPS

    by SSdoxie
    Replies
    4
    Views
    330

    Re: ROPS

    The overall height of a CT335 is lower (about 1 1/2") than the CT225-235. I don't know why, but there was not a change in ROPS design and the ROPS structures and mounting to axle frames are...
  3. Replies
    2
    Views
    306

    Re: earthforce backhoes

    Earthforce backhoes were bouth out and became Bobcat backhoes then eventually discontinued but Bobcat still has parts for them. Here is a link from the Bobcat Construction Equioment forum re: B200...
  4. Re: Bobcat Zero Turn Recall due to crash hazard

    The only mowers Bobcat Company builds are attachments to hook onto tractors, loaders, toolcat, or UTVs. Self propelled bobcat mowers are, or used to be built by Ransome. Not sure about Ransome's...
  5. Re: adding a hydraulic top link and hydraulic rear blade Kubota B3000

    A diverter/selector valve works great for this versus cost of adding second remote kit. Either electric as travlitt mentioned or simple manual control and mount it where it can be easily reached...
  6. Replies
    33
    Views
    1,363

    Re: Carhartt insulated bib overalls

    I bought a pair of Schmidt this year. I'm mostly arms and legs and the Carhart in same size left crotch half-way to my knees even with straps shortened all the way.
  7. Replies
    9
    Views
    534

    Re: which way to mount R-4 tires

    To get the valve stem on the outside you will need to move wheels from side to side. I took mine apart once, they are also filled. What I found to work easiest is park close to a wall but leaving...
  8. Replies
    12
    Views
    662

    Re: hydraulic hose question

    If 1/4" is what is on the valve pump is low enough to get minimal restriction with 1/4" hose, but I tend to error to a larger size just to be safe. Not much difference is price from 1/4". 3/8", or...
  9. Thread: heater

    by SSdoxie
    Replies
    5
    Views
    794

    Re: heater

    FYI, jsut because you can see the lever move on outside of the valve does not mean it is working. Majority of time when these fail, the actuator lever moves but has come loose inside and valve is...
  10. Thread: Coolant leak?

    by SSdoxie
    Replies
    7
    Views
    619

    Re: Coolant leak?

    The block heater is above the main frame but do have to take the lower shroud off the get at it. 3 possible places it could be leaking. 1. heat element is loose in heater and coolant seeping past...
  11. Thread: heater

    by SSdoxie
    Replies
    5
    Views
    794

    Re: heater

    Have you checked the heater valve, in the hose going into the heater core. Make sure it is opening. All else fails take the 2 hoses off and connect the together (eliminate the valve to see if you...
  12. Replies
    26
    Views
    1,016

    Re: joystick freezing up in cold weather

    Check for moisture in the valve spool end caps (opposite end of spool from joystick connection), caps can get moisture in there, freeze and stop spool from moving either both directions or jsut one. ...
  13. Re: Hooking a bobcat attachment to a john deere

    The bobcat 7 pin harness uses 2 12v power wires, the remaining are grounds and data cables communicating with controller on the attachment. The 12v goes into the controller then depending on button...
  14. Replies
    30
    Views
    1,339

    Re: House Construction - Best Value Dimensions

    35' long is odd measurement when calculating rafter spacing @ 2' OC & stud and joist spacing @ 16' OC. Sheating is small fraction of the cost and at 35' likely to have more waste. Adding the extra...
  15. Thread: sb200 trouble

    by SSdoxie
    Replies
    3
    Views
    852

    Re: sb200 trouble

    Only 2 ways to identify if controller is the problem.
    1. Have dealer hook his computer, analyzer to the machine with the blower connect and he can check to see if it is communicating correct inputs...
  16. Replies
    7
    Views
    294

    Re: Piston disassembly help and ideas

    Never done this but just and idea. Get a toggle bolt, large as possible but will fit through the piston, then drill hole for bolt diameter in piece of steel to go across end of the barrel. Bolt...
  17. Replies
    8
    Views
    343

    Re: Tire chains for 5600

    Tim has offered very good ideas based years of experience. If installing chains do all 4 tires. The 5600 is full time 4wd, with at least 1 front and 1 rear wheel pulling. Putting chains on just...
  18. Replies
    12
    Views
    706

    Re: TSC 22 ton log slitter

    What JJ is trying to get you to test is if seals are by-passing or nut on cylinder rod has come loose. Take the hose off of the rod end cylinder, put a steel plug (that fits the hose fitting) in...
  19. Thread: loader rams

    by SSdoxie
    Replies
    13
    Views
    999

    Re: loader rams

    Blake, I have yet to take one of these apart. Read about it in the book but reading and doing are sometimes 2 different things. I suggest you ask this question in the Hydraulics forum and post the...
  20. Re: Whats the value of performing the 50hr service at 25hrs

    If you do it at 25 hr, should be no need to do again at 50. Engine manufactures I have worked with have told me they set the first change at 50 hoping to get vast majority of customers doing it...
  21. Replies
    27
    Views
    1,354

    Re: Building a fireplace (ventless) question...

    I installed ventless propane log set in my masonry (wood burning) fireplace 15 years ago, and still working fine. I formed a piece of sheet metal to fit in top of the fireplace to block off the flue...
  22. Replies
    30
    Views
    2,085

    Re: Starting a tractor by spinning the PTO

    If I tried that, with my luck, I would rip the brushcutter of the back of the tractor.
  23. Replies
    8
    Views
    1,075

    Re: edit / delete post function

    Try going to "tool" on tool bar of Browser, and click Compabilty View. See if that helps.
  24. Thread: loader rams

    by SSdoxie
    Replies
    13
    Views
    999

    Re: loader rams

    You just got to know where to look. :cool2:
  25. Replies
    3
    Views
    344

    Re: Broken tension pin on a DK50HSE

    Take the linkage rod off the bell crank/lever, then pull the lever off. Push the broken pin out if still in hole in rod. Put a long pin in and that combined with vise grip or similar to shift it...
  26. Thread: loader rams

    by SSdoxie
    Replies
    13
    Views
    999

    Re: loader rams

    I didn't pay close enough attention to the model, that part number is for a 7TL on CT2xx models with Rhino loader. To find it in online catalog: Scroll down through the model selection to find...
  27. Thread: loader rams

    by SSdoxie
    Replies
    13
    Views
    999

    Re: loader rams

    Item #16 on parts diagram = p/n 6693558 cylinder seal kit.
  28. Replies
    2
    Views
    327

    Re: Removing / Dismounting FEL from CT230?

    It is not difficult, especially after doing it once or twice. Secret is to be sure the rear tractor tires are setting on the same plain as the loader bucket. If not able set on concrete slab, put a...
  29. Replies
    7
    Views
    854

    Re: Bobcat 331 Won't shut off

    If dash lights or guages turned off with key, then problem not likley in ignition switch. The fuel solenoid is power on, spring loaded off. It uses 2 circuits for on. 1st is high amp pull that is...
  30. Replies
    13
    Views
    855

    Re: Tractor hydraulic pump whine noise??

    Cooler oil flowing through the lines and across the pump create a vibration/whine. When some pressure is applied by moving the loader, the pressure pushes against the pump and lines stopping the...
  31. Replies
    25
    Views
    1,245

    Re: forks or no forks

    Forks are one of those tools that once you have them you wonder how you ever got along without them.
  32. Replies
    5
    Views
    1,630

    Re: Bobcat 337 hydraulic malfunction

    weedee, that disc is the engine half of the pump drive coupler that Brian and & I mentioned. Thanks for coming back and letting us know.
  33. Replies
    14
    Views
    1,378

    Re: Hydraulic Top links

    I have had hydraulic top link for going on 4 years now. I can still remember the agony of hooking up implements and constant stopping to get off and readjust with the manual link. I would never be...
  34. Replies
    16
    Views
    1,460

    Re: Quick Connect for FEL Bucket

    Remote (hydraulic) operated from the seat can be done, just a matter of how you set up the locking levers and cylinder or cylinders. I went the manufacture route and bought the SSQA, and all of...
  35. Re: can a ct235 be put in to neutral so we can drag in behind a truck?

    Putting speed range selector in neutral will let you pull it without turning the hydrostatic pump. Put it in neutral and tow it.
  36. Thread: Bobcat T250

    by SSdoxie
    Replies
    6
    Views
    1,051

    Re: Bobcat T250

    Smoke of some sort indicates you are getting fuel. Black smoke is too rich mixture:
    1. Make sure air filters are clean.
    2. At about center of the muffler on the bottom is a pipe plug (muffler...
  37. Thread: Bobcat T250

    by SSdoxie
    Replies
    6
    Views
    1,051

    Re: Bobcat T250

    Any smoke coming out the exhaust? Gray, black, or other color?
  38. Replies
    8
    Views
    2,599

    Re: Toolcat for our company

    A,B, & C series have leaf springs on rear axle with no shocks and front has coil springs with shock absorber inside the spring.
  39. Replies
    44
    Views
    4,369

    Re: To fill or not to fill

    I run 12 - 14 psi in my R1 Ag tires. Put valve stem at very top (12:00 position) push in on valve core and some fluid will come out then will start with straight air unless tire is over-filled.
  40. Replies
    3
    Views
    1,923

    Re: c225 fuel guage sticking

    Identify what the sending unit float is catching on then take out the sending unit and bend the float rod slightly to clear the obstruction.
  41. Replies
    44
    Views
    4,369

    Re: To fill or not to fill

    I ran the first 40+ hrs. without filling then trying to decide if I wanted filled tires I bought the fill adapter at TSC and filled with water. Within a week I drained the water and filled with...
  42. Replies
    11
    Views
    2,538

    Re: bobcat brush cutter

    rhino made the early loaders then Bobcat started making their own in 2010. I "think" the cutter is Rhino.
  43. Replies
    27
    Views
    2,405

    Re: Welding spring-steel rock-rake tines

    I have close to half-dozen broken off on my 6'. None are at the blot hole, all are somewhere in the bend or just above it. I would love to try and reweld them just to see if I could. My problem is...
  44. Replies
    9
    Views
    336

    Re: Boat storage question

    I try to run my tanks (2 boats) down to very little left when storing. Then put fresh gas in when taking it back out. I do this because the 1 time I did leave tanks full and treated with Stabil the...
  45. Replies
    251
    Views
    62,825

    Re: If you have Toolcat questions, ask them here...

    Loose connection somewhere. Could be @ switch, fan, relay, fuse. Inspect each and try wiggling the wires, with fan running, close to them to see if you can make it shut off.
  46. Replies
    6
    Views
    500

    Re: ford 8n what are the chances

    Could be a bad starter, but a double check ground connection(s) from engine to battery also.
  47. Replies
    28
    Views
    2,724

    Re: Tier 4 Here I Come

    Don't look for any inventory reduction sales on existing inventory when the 2015s start showing up. Right now this horsepower range is at interim T4, adding the DEF to it will take it to final T4. ...
  48. Re: 2010 Kioti DK35SE second remote kit part number

    Bobcat part number for that complete kit is 7172968. List price is about US $320.
  49. Replies
    1
    Views
    1,427

    Re: CTL - Washing out the belly pan.

    There are round or oval shaped plates in front corners of the lower frame to take out for cleaning. You may need to do both front end high and rear end high to get it cleaned out. Note: the engine...
  50. Replies
    5
    Views
    1,630

    Re: Bobcat 337 hydraulic malfunction

    If the blade will operate but nothing else, then problem is likely to be in the Lockout solenoid electrical system. Blade is only function that is mechanical on that year machine all the rest are...
  51. Replies
    44
    Views
    3,481

    Re: Teuck bed to flatbed, would you convert?

    I see you are in Lebanon so not too far from McMinnville. There is a guy East of McMinnville on 70S that has (or did have last 4 times I have been past there) truck beds setting on his lot. He is...
  52. Replies
    4
    Views
    310

    Re: Metric chain question

    Try this site:
    Ametric - Premium Metric
  53. Replies
    8
    Views
    522

    Re: P.T.O. ....R.P.M. Question

    Not necessarily, more likely probably not. The PTO speed is usually designed to be at or very close to optimum torque speed of the engine. Based on engine torque at given RPM the PTO gear reduction...
  54. Replies
    8
    Views
    522

    Re: P.T.O. ....R.P.M. Question

    If running engine RPM of both tractors to the PTO mark on the tach, they should be the same. Were you running at the PTO mark on the JD or running at same engine RPM as the Kubota? Engine RPM @ 540...
  55. Replies
    6
    Views
    337

    Re: CT225 hydraulic hard line leak

    Could be, or O-ring got pinched when installed and finally started leaking.
  56. Replies
    6
    Views
    337

    Re: CT225 hydraulic hard line leak

    The groove is in the collar of the steel line.
  57. Replies
    31
    Views
    1,304

    Re: Hydraulic SSQA Plow Troubles

    With only the Regen function on the dump stroke, if you connect the DA plow cylinder so the rod extends when moving lever to the right it will work. Hook it up the other way and it will lock stall...
  58. Replies
    10
    Views
    688

    Re: Anybody replaced a battery yet

    I had dealer replace the battery when I got it because tractor had been sitting on the lot for 1& 1/2 without any recharge. Little over 3 years and going strong. Battery cable clamp corroded and...
  59. Replies
    6
    Views
    337

    Re: CT225 hydraulic hard line leak

    it has O-rings where LD1 explained. 1 between the bolt flange and line, another between line and housing.
  60. Replies
    8
    Views
    780

    Re: Bobcat S570 control options

    A minor correction on some information: The iT4 Kubota in the S570 is NOT electronic control. It is mechanical injection with manual throttle and uses an EGR to meet iT4 compliance for this HP...
  61. Re: Axial Pump ID and Locate Similar Replacement

    The 4 ports on the pump are: 2 are the work outlet ports. The one on top at rear is suction inlet for the charge pump built into the back of the pump and the 4th (top front) on the case is Case...
  62. Replies
    72
    Views
    4,668

    Mowing Re: PTO won't disengage when using brush hog

    I don't have this style tractor but it certainly sounds like the over-run clutch is hung up/stuck. Two possible solutions:
    1. Take pto assembly out and repair it,
    2. Buy an external PTO Over-run...
  63. Re: Bucket Forks - Can't find the thread I am looking for...

    Is this the one you are looking for?
    http://www.tractorbynet.com/forums/build-yourself/314731-cheap-pallet-forks.html?highlight=Cheap+Plaaet+forks
  64. Thread: Woe is Me

    by SSdoxie
    Replies
    27
    Views
    2,040

    Re: Woe is Me

    Around here it is photo ID, thumb print, and check is mailed to address on ID for copper sales. No A/C units or parts of are accepted except from person holding an HVAC license. It has slowed...
  65. Replies
    43
    Views
    1,703

    Ballast Re: Water in rear tires = more stable??

    Interesting comments here about cast iron wheel weights versus filled tires especially because Titan was one of the companies mention. My tractor has Bobcat branded tires made by Titan. The wheels...
  66. Replies
    2
    Views
    243

    Re: C_K 25 will not start

    If it went to full throttle and would not come back down when moving the throttle sound like the classic case of gears stripped in the injection pump, but I didn't think this age (05) tractors were...
  67. Replies
    27
    Views
    990

    Re: Blind bolt options?

    How much extra cover flange does the grab handle have? Is there enough cover to shift it over and drill new holes and install 2 new inserts, even if you had to order closest SAE size to the current...
  68. Replies
    27
    Views
    990

    Re: Blind bolt options?

    You sure about that?? My Mama always told me 3 wrongs to make it right. :cool2:
  69. Thread: Hyd question

    by SSdoxie
    Replies
    1
    Views
    204

    Re: Hyd question

    Just a guess only: 1/2" hose is very common so is possible at time these were made the cost per foot of 1/2" was less than using smaller hose. Reducing to 3/8" fittings was probably to help slow...
  70. Replies
    16
    Views
    1,073

    Re: Excavator track options

    Difference in ground pressure of the 18" rubber versus 24" steel is because of the extra width. Ground pressure is = total weight of machine spread over the surface area of the track, wider track...
  71. Replies
    8
    Views
    780

    Re: Bobcat S570 control options

    Bobcat was the first to introduce "operate by wire" (electric over hydraulics) control in skid-steer and track loaders. They did encounter some problems, part of this was a learning curve on...
  72. Replies
    28
    Views
    1,395

    Re: DK45 HST won't start

    Before you start changing modules, Identify if you are getting both voltage inputs. You getting one of them, the 12v from the fuse, otherwise you wouldn't have any voltage feed to the Potentiometer....
  73. Replies
    28
    Views
    1,395

    Re: DK45 HST won't start

    Bobcat had a better idea?????????????? :cool2:
  74. Replies
    16
    Views
    991

    Re: CT230 - Won't turn over

    I haven't had anything get caught in the travel pedal switch YET, but did find out a few months back that there is a "sweet spot" in the PTO lever that will cut out the safety switch but not move it...
  75. Replies
    28
    Views
    1,395

    Re: DK45 HST won't start

    Ken has been posting this on both Kioti and Bobcat forums. Below is the Bobcat schematic. I wanted him to check for proper inputs, but according his response on Bobcat forum the wire colors are...
  76. Re: Bobcat 943 Hydraulics operates in only one direction

    Something is blocking the flow of oil through the Open Center port of the Auxiliary spool. Either the spool is shifted, not in neutral or something plugged in the spool.
  77. Re: Bobcat 943 Hydraulics operates in only one direction

    Since that post is 2 & 1/2 years old, I hope he got it fixed. Hydraulics moving one direction only on both lift and bucket (cylinders extending, but not retracting) is caused by the control for...
  78. Re: Fitting towable sicklebar mower to 3 point

    Use a 3 point stabilizer/stay strap set up on the 3 point draw bar currently using. It consists of an upper and lower half (2 bars per side) that fasten to the top link bracket of the tractor and...
  79. Replies
    5
    Views
    1,211

    Re: CT 445 won't start

    The sensor works on a 5 volt input with reduce voltage variance fed back to the module, depending on shift lever position. Check the red/with white stripe wire for 5 volts and check feedback voltage...
  80. Replies
    5
    Views
    729

    Re: T190 fan motor hose leak

    That hose does carry charge pressure (about 350 - 420 psi), but if the charge relief stuck causing the hose to fail it would have given a "Charge Pressure High" code before the leak started and shut...
  81. Replies
    5
    Views
    729

    Re: T190 fan motor hose leak

    The hose from fan to pump has JIC fittings to unscrew from the pump fitting. Raise the cab and place something to lay on across the steering lever panel to the top of the pump (a heavy cardboard,...
  82. Replies
    7
    Views
    420

    Re: BobTach Removal

    Yes, you can shorten the end pin somewhat to make sure it pulls in tight without contacting the washer. One thing I do when putting these pins back in; remove ALL grease from the pin and Bobtach...
  83. Replies
    13
    Views
    636

    Ballast Re: How heavy a rotary slasher

    DK35 is rated at 850# on 3 point without any front ballast. If it has a loader that rating doubles to 1700#.
  84. Re: Hay bale grapple on a 7tl loader - Capacity?????

    Use extreme caution although your proposed bale load is about same as the pallets I lift, the bales will be out wider an farther forward. Plus I have never tried going to full height with that load.
  85. Replies
    7
    Views
    420

    Re: BobTach Removal

    After removing the from the outside of each lift arm, push the pin that the bolts were threaded into back in towards the Bobtach. Push the pins back far enough so the ends are inside the Bobtach and...
  86. Re: Hay bale grapple on a 7tl loader - Capacity?????

    A 2011 tractor would have the newer Bobcat built loader, look at the serial number of the loader (not tractor) 1st 4 digits of number would be either AL4D or AKPD, depending on if it is Bob-tach...
  87. Replies
    13
    Views
    9,037

    Re: 863 Fuel pickup

    The fuel pickup line and the excess fuel return lines go into the top of the tank, look just behind the pump assembly and in front of the engine. These lines go through 90 degree barbed fittings...
  88. Thread: Bucket problem

    by SSdoxie
    Replies
    4
    Views
    511

    Re: Bucket problem

    The blinking light "tilt valve" is giving you a diagnostic code. Count the number of flashes between each pause, this will help determine if problem is in control handle, wire harness, or tilt valve...
  89. Re: Put truck and car on same trickle charger for a month?

    If your batteries won't hold charge for a month without a "maintainer" connected you need new batteries. I have 3 vehicles setting that don't get started/driven but once every 2 - 3 months and have...
  90. Replies
    11
    Views
    2,413

    Re: Small hay grapple.

    I would try lifting and carrying the bale(s) any great distance, the bouncing across the field could cause the hay to tear loose at the hooks. It doesn't seem to hurt the bale any to slide it. I...
  91. Replies
    2
    Views
    860

    Re: 337 hydraulic drive idiot light

    The only light that works, has anything to do with drive is the 2 speed (Hi-range) indicator light. It lights up when in 2 speed.
  92. Replies
    26
    Views
    1,146

    Re: Leakdown Test Results

    I second the vote for wet & dry compression test comparison. Engine air leakage, like hydraulics or water, takes the path of least resistance so if valves are in worse shape than the rings the...
  93. Re: T190 ser. 531615995 with intermitant "no hyd.functions and drive"

    Sounds like you have a loose or corroded wire connection somewhere in either plug to drive controller or to the main controller. Another possibility is partially broken wire in the harness. Loose...
  94. Re: Tractor Supply 3 point Hitch Wood Splitter on Kubota B3030

    poosniffer, Thanks for posting that video. I have been thinking about that same splitter for some time now but was trying to decide if the cycle time would be good enough for my limited use. I can...
  95. Replies
    31
    Views
    2,335

    Re: Can somebody tell me what made these marks?

    Just guessing, could be jaw marks from some type of log clamp if whoever pick up some of these used some type of grapple.
  96. Re: Is it better to use gear oil or trans fluid in front axle of FWA Kubotas?

    One word answer = Either.

    BabyGrand's statement was right on. "I think the manufacturers use the hydraulic fluid because it meets the requirements and they avoid the risk of "which oil goes...
  97. Replies
    17
    Views
    718

    Grading Re: New (used) CK20 owner

    Top link for the CK20 has same part number as my CK27 in Bobcat parts catalog. Fully retracted length is 19 3/8" center to center of eyes. Threaded sleeve is 14" so leaving minimum 2" of thread...
  98. Re: Transmission oil seeping up around both gearshifts

    Might want to send PM to "Soundguy" (his user name on TBN), he is the Ford guru on here. He will know where the vent is.
    Another thought, are the shift lever boots cracked or has tractor been...
  99. Re: Water ballasting experience. Increased fuel consumption?.

    I haven't noticed any difference in fuel consumption either way. What I did find after loading the rears was reduced front tire wear. Before loading the rears I had so many times that I needed 4WD...
  100. Replies
    13
    Views
    4,825

    Re: HELP! Bobcat S185 trouble

    Correct, one of the 2 12v supplies to the ACS controller is shared with the Auxiliary control/harness. A short in the Auxiliary can blow fuse and/or create an over voltage to short out the ACS...
Results 1 to 100 of 2143
Page 1 of 22 1 2 3 4
© 2014 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.