Search:

Type: Posts; User: Outlander; Keyword(s):

Results 1 to 100 of 136
Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. 3-Point Hitch Re: Cub Cadet 7195 - 3 point hitch stuck in up position

    There may be a knob straight down from the front edge of the bottom of your seat. If that got tightened I think it will lock the 3-point. Give that a twist and see what happens?
  2. Replies
    1
    Views
    682

    Re: 2615 filter question

    I have been down this road....I actually have three after market filters on the shelf which I won't use. When you compare them to the Mitsubishi filters they are NOT the same. They will attach but...
  3. Replies
    3
    Views
    1,259

    Re: Mid Mount Mowers

    The 15's with the Woods MMM are drive over. I was visiting the local Mahindra shop and was looking at a couple of 15 series on the lot. They definitely had the Woods mower. That said I have seen...
  4. Replies
    4
    Views
    856

    Re: HST fluid drip- filter somehow?

    Be sure to check the tension on that upper banjo behind the gas tank on the left side. Those have a tendency to work loose and leak a bit. Sometimes a lot..... Just me but I would junk the collected...
  5. Replies
    4
    Views
    2,114

    Re: Mahindra 2015 - hard to start

    A dead glow plug or two no doubt?
  6. Replies
    7
    Views
    1,096

    Re: Glow Plugs stay on longer than 3 secs

    Just unplug the wire fron the GP temp sensor on the back of the top coolant outlet. Full 10 sec every time.
  7. Replies
    9
    Views
    1,247

    Re: 2015HST Whine

    Any chance the 2516 pump would bolt up to the 2015?
  8. Replies
    9
    Views
    1,247

    Re: 2015HST Whine

    Those pumps are dinky and you must keep the rev's up a bit to get sufficient fluid to the various components. The whine is annoying but alas normal. Probably a bit louder in the Winter? Sometimes a...
  9. Replies
    5
    Views
    1,247

    Buying Advice Re: I just looked at a 7200

    7205= 4x4 Hydro
    7200= 4x4 Gear
    7000= 2WD Gear
  10. Replies
    14
    Views
    10,018

    Re: Cub Air Filter

    Those Kubbota filters work perfectly. I have been using them in my 7205 for several years now.
  11. Replies
    22
    Views
    5,645

    Snowblower Re: Mount 2 snowblowers to bucket?

    When it comes to snow removal I am a firm believer in the low bucks approach. This is a GREAT idea! Definitely pix!
  12. Replies
    17
    Views
    7,126

    Oil & Fuel Re: 7000 series diesel won't start, need help!

    Try unplugging the controller temp sensor wire from the rear sensor (I think) on the top water outlet. This will put the controller in max on mode which is good for 10-12 seconds every time. You...
  13. Replies
    5
    Views
    2,183

    Re: Cold weather starting

    Just unplug the wire on the controller sensor on the top water outlet. Puts the contoller in timer mode only and you get the full 10-12 seconds every time. That in conjunction with a lower hose...
  14. Thread: cub 149

    by Outlander
    Replies
    3
    Views
    968

    Re: cub 149

    I had a 149 sans lights. According to the service manuals which are still around here somewhere, the lights were an option.
  15. Replies
    19
    Views
    11,344

    Re: 2015 Glow plugs burning out

    It's under the panel below the steering wheel. It's plastic so be careful in the cold. Maybe 2 bolts on each side? Don't over tighten or you will crack it. Check the Cub Cadet forum......there was a...
  16. Replies
    19
    Views
    11,344

    Re: 2015 Glow plugs burning out

    There are two different part numbers for the controller and two different numbers for the plugs. They supposedly are supposed to be matched. I went through this last Summer and I really expect it...
  17. Replies
    4
    Views
    951

    Re: 2015 HST with post hole digger

    I use a standard TSC (Speeco) on my 7205/2015. No problems at all. However if you are going to use an auger extension you do need to drill down a bit and then insert the extension. I think that might...
  18. Replies
    4
    Views
    2,089

    Oil & Fuel Re: 6284 Engine Oil

    Probably a dumb question but did you start it to fill the filter?
  19. Replies
    4
    Views
    4,438

    Snow Re: snow plow fel attachment

    The one I looked at had no trip. I think those blades are actually sliding back blades with a different mounting arrangement and a considerably higher price than the back blade would be?
  20. Replies
    4
    Views
    4,438

    Snow Re: snow plow fel attachment

    I looked at that same model plow too. Same concerns as Thomas. My biggest one though was the $900+ price. Can't see spending that for something that sits idle for nine months unless you are going to...
  21. Replies
    9
    Views
    1,307

    Re: 2516 Diff lock question.

    Apologies for stating the obvious but this might need to be done while the machine is not in motion. Mine will not engage if it is moving.
  22. Replies
    2
    Views
    2,142

    Re: Hydro-Tran fluid for 2615HST?

    Mixing has always made me uneasy. Probably just me but you are playing with chemistry and heat. As long as your fluid meets the Hytran spec you are fine. When Cub sold those Mitsu's they quite often...
  23. Replies
    20
    Views
    7,817

    Re: Broken engine mount bolts.

    Carbide drill bit should do it. Go slow and lubricate. Carbide bits can be a tad brittle.
  24. Replies
    12
    Views
    4,176

    Snow Re: 5000 Series Snow Plow / Dozer

    Just get a used ATV blade and bolt the mount to your frame. You can do 5-6' with that tractor but probably no more. I have one (6') I mount to my bucket and it works great. Been using it for years...
  25. Replies
    27
    Views
    5,111

    Re: 15 / 16 series block cracks

    This was an issue with some CC Mitsu models. If I remember it was resolved with a brace and bolt tightening. I think the Woods loaders had a pic of the supplementary brace in the parts literature....
  26. Replies
    2
    Views
    627

    3-Point Hitch Re: 3 pt hitch drifts down after hot

    The lift arm actuating cylinder may well have a leaking seal. Also check the line to that cylinder to be sure all is well there.
  27. Replies
    7
    Views
    1,805

    Re: How is Mahindra affiliated w/ Mitsubishi?

    \

    Amen to that!
  28. Replies
    3
    Views
    1,655

    Re: Warner 5218-6 PTO

    Either take them out and visit your local bearing supply or get the numbers from them and go from there. Pray they are nor proprietary.
  29. Replies
    41
    Views
    8,494

    Re: Wheel spacers for Mahindra 2615, 2815, 3015

    Ebay Item number: 220398130079. Price is ridiculous but these guys will dicker now and then.
  30. Replies
    16
    Views
    9,465

    Grading Re: Help? Broken mower blade bolt

    Carbide drill bit, moderate heat and pray you don't break the EZ out. You need to ask yourself if you tend to be heavy handed? If so, take it to a machine shop. Sometimes those gear boxes are only...
  31. Replies
    9
    Views
    1,711

    Oil & Fuel Re: D2000 spitting oil out of exhaust

    Diesel exhaust can have a acrid scent at times. What is "burnt rubber" to you might be something else to a different nose. If it was idle for some time there is a fair chance that some form of...
  32. Replies
    9
    Views
    1,711

    Oil & Fuel Re: D2000 spitting oil out of exhaust

    My bet is black water. It is nearly impossible to keep condensate out of exhaust systems. Take a look at your auto exhaust after a cold start. Black water. The stuff from a diesel might be a bit more...
  33. Replies
    5
    Views
    705

    Re: Generator Oi Change

    Mine sits out and exercises once a week. I see some evidence of condensation around the filler cap after 3-6 months. It's to be expected so I change in April and again in November. I think twice a...
  34. Replies
    5
    Views
    1,660

    Oil & Fuel Re: Mitsubishi 3L3-Y-2 Series 3cyl diesel

    The disk with all the 2815 and 3215 parts and service info appears on Ebay with some regularity. I have had one for a while now and I think it was $18-$20. That's what you really need no doubt.
  35. Replies
    7
    Views
    3,003

    Re: Mystik hydraulic fluid?

    I've been using Mystic for several years. My hydro is maybe a bit quieter with it. I switched from Hytran. It's good too. Check the interchange list for Mystic. It's fairly impressive. That's what...
  36. Replies
    4
    Views
    1,511

    Re: trouble with SATOH Bison

    If you used a carb kit and it had a float valve with a viton tip, it may well be sticking. Those rubber tips are nortorious stickers. If no kit you may have inadvertently (of course) bent the float...
  37. Replies
    7
    Views
    1,185

    Re: Biodiesel in a Mitsubishi MT300D?

    You should post this in the fuels and lubricants section. I might be dreaming but I thought there was some past discussion about mixing bio with regular to negate the problems you mentioned?
  38. Replies
    5
    Views
    1,660

    Oil & Fuel Re: Mitsubishi 3L3-Y-2 Series 3cyl diesel

    Look online for Mitsu marine, generator and industrial engines. All of the Mitsu 3's are used in many, many other apps.
  39. Replies
    9
    Views
    1,274

    Re: Water in Hydraulic Fluid

    I would not get too bent out about a little water in the trans fluid. It's a way of life with tractors. If you think you will prevent this you are going to drive yourself nuts. I learned this around...
  40. Re: 2415 keeps getting pin hole's in front loader hydraulic lines

    Vandalism?
  41. Replies
    3
    Views
    2,121

    Re: Mitsubishi 1600D New Owner

    Post on the Mitsubishi forum. You might be surprised just how much info and how many parts are available if you really look. You definitely need to find out if the tractor had a US market clone....
  42. Replies
    16
    Views
    9,447

    Re: Mahindra 3510. Overheating

    A couple of odd ball possibilites.....
    Wrong coolant mix. Most mfrs recommend 50-50 to 70-30 mixes. Pure water cools best, and the cooling ability, not boiling point...actual heat
    rejection...
  43. Replies
    5
    Views
    3,617

    Re: Cub Cadet 149

    I had a 149 for 12 years. Good little mower. The electric PTO sounds like a monster project. Why not rebuild your old PTO clutch? If the friction material is gone have it relined, get some new...
  44. Replies
    13
    Views
    8,768

    Re: Cub Cadet 7205 Question

    Save your money. The voltage is different. The old number is 10.5V, The new ones are 8V.
    The old ones fit oerfectly. They are 10mm. Problem is... they don't heat correctly with the newer controller....
  45. Replies
    13
    Views
    8,768

    Re: Cub Cadet 7205 Question

    In order to use the older plugs you have to have the older controller, harness and maybe the relay. Most of the later 7000's used the QGS (quick glow system) plugs and controller and the earlier Case...
  46. Replies
    13
    Views
    8,768

    Re: Cub Cadet 7205 Question

    Thanks for that picture. It's great! That will save me time this Summer as I intend to investigate some comtroller options before next Winter. I sure hope that solves your problem permanently. I...
  47. Replies
    3
    Views
    845

    Re: Mitsubishi S650G want race and dies off

    And distributor shaft side to side wobble.
  48. Replies
    13
    Views
    8,768

    Re: Cub Cadet 7205 Question

    Sounds like you did OK with Messicks. I was thinking about ordering my next GP from them. I've never had all three go bad at once so now I guess I feel better. Thanks. I usually average one a year...
  49. Replies
    13
    Views
    8,768

    Re: Cub Cadet 7205 Question

    Those diagrams can be useless when it comes to pinpointing the location of various components. Sometimes they are OK. I just looked at my parts and service manuals plus the tractor and still don't...
  50. Replies
    2
    Views
    748

    Re: popping noise in a 2815 hst

    Make sure you have not lost or loosened a stay chain which will cause a lower lift arm to flop over and catch a tire in a turn. Happened to me and caused me a worry for a bit.
  51. Replies
    14
    Views
    3,728

    Re: 2015 HST purchase question (problem)

    Hmmm...Faded paint, leaking oil, Maybe fate is telling you to walk away from this one. You need to be comfortable with this and it sounds like you are not. Listen to the voice in your head and get...
  52. Replies
    3
    Views
    1,001

    Re: s650g hydraulics quit

    Could be the fluid has collected enough water over time to clog the filter with the dreaded marshmallow topping? Check your filler cap(s) and see if there is any white residue. If so be suspicious.
  53. Re: Rear wheel bolts on 2815 fine or course thread??

    More like 17+ depending on the diameter. . The common and useful ones are 1.0, 1.25 1.50 and rarely 2.0. That is just in ISO. For those who have been working with metric fasteners since the 1960's...
  54. Re: Rear wheel bolts on 2815 fine or course thread??

    There are two fines 1.25 and 1.50. Buy the gauge?
  55. Replies
    16
    Views
    2,694

    Re: 2615 wont start

    cold...hydraulic pump rattling noise"
    How on earth can you even hear a pump noise over the cold engine diesel clatter? Get the big Walmart battery. I junked the original before the first Winter. I...
  56. Replies
    4
    Views
    1,659

    Re: Mahindra 1815 hst

    Hi Range is great for plowing snow. Momentum is King with low HP.
  57. Replies
    115
    Views
    28,639

    Re: New Mahindra Trucks

    Don't forget your 3215 is a Mitsubishi not a Mahindra.
  58. Replies
    11
    Views
    1,820

    Re: 3 point no longer operates

    Any chance the lift cylinder for the 3 point has a blown or leaking seal? What you describe sounds very familiar......
  59. Replies
    11
    Views
    2,320

    Re: Which engine heater for 2615

    The hose heater is the logical choice given the price of the Mitsu block heater. I have a 600 watt Kats 1 1/4" and it is great. In one hour it heats the block and the radiator. When I start up the...
  60. Replies
    8
    Views
    4,646

    Re: satoh beaver 370s help

    Finally! Someone who understands.........
  61. Replies
    1
    Views
    1,176

    Re: 7275 Front axle problem

    You need literature. For a start go to partstree.com and check out the diagram for that hub. Maybe a problem snap ring or some such? Or worse? Call Cub and order the service manual or try to download...
  62. Replies
    7
    Views
    6,488

    Re: Cub Cadet 7000

    The latest part number for the 7000 series glow plugs seem to run $40 to $46 per plug depending on the source. If anyone knows of a cross please post. I have searched to no avail. Those seem to be...
  63. Replies
    11
    Views
    2,676

    Re: Mahindra 2615 Hydro - 2007

    Just because the glow plug light comes on does bot mean the glow plugs are actually working. Pull the plugs and test them. Simple way... attach a lead from + post to plug terminal. Ground the plug...
  64. Replies
    7
    Views
    6,488

    Re: Cub Cadet 7000

    Very heavy duty and reliable. Mahindra now sells the Mitsu line as the 15/16 series. $5800
    seems OK for 140 hours. My 7205 is heading for 400 hours with no issues except it will eat a glow plug now...
  65. Replies
    6
    Views
    2,282

    Re: Case IH 275 Starter selonid

    Post on the Mitsubishi forum. The 275 is a Mitsu and someone there will know about a possible parts interchange.
  66. Replies
    58
    Views
    12,349

    Snow Equipment Owning/Operating Re: Turf or Ag tires for snow removal

    Turfs with 2 link ice cleat ladder chains.
  67. Mowing Re: 2615 hst heating issues using a finish mower

    Just take off the side panels....End of problem. I've been doing it for years with no ill effects. Just blow the engine off with air now and then. I really don't get side panels at all. Over the...
  68. Thread: Satoh 550

    by Outlander
    Replies
    5
    Views
    1,406

    Re: Satoh 550

    There are one or two Mitsu parts suppliers that offer advice on this board. Check the old posts and I'm sure you will find some leads. I would try NAPA too. If you can find someone to dig deep...
  69. Thread: Satoh 550

    by Outlander
    Replies
    5
    Views
    1,406

    Re: Satoh 550

    Rebuilt by whom? This thing just might be worse than what you already have. You could buy a bunch of carb kits and service literature for $400. Plus you would learn a lot.
  70. Replies
    34
    Views
    6,320

    Re: 650G - Burning through plugs!

    Another problem I had with my Allis was fuel starvation and or flooding due to the use of the rubber tipped float valves supplied in contemporary rebuild kits. The valve would either jam in the seat...
  71. Replies
    16
    Views
    2,786

    3-Point Hitch Re: 3Pt Hitch will not raise

    I have used kero as a gear tranny flush many times. Works great. I usually start up and let it slosh around a bit. I like to let it drain overnight and then refill. If your flushing hydraulics I...
  72. Replies
    16
    Views
    2,786

    3-Point Hitch Re: 3Pt Hitch will not raise

    There is always the possibility that the seals in the lift cylinder are bad?
  73. Replies
    34
    Views
    6,320

    Re: 650G - Burning through plugs!

    Is your distributor shaft running true? My old Allis was doing the variable points thing some years ago and it turned out that the bushing that bears the distributor shaft was worn to an oval. Would...
  74. Replies
    5
    Views
    1,345

    Mowing Re: Need photo of belly mower for 15 series

    Interesting? Perhaps you could explain why Woods recommends the "drive over" method in their service manual? I have been using their recommended method twice a year for several years now and it...
  75. Replies
    5
    Views
    1,345

    Mowing Re: Need photo of belly mower for 15 series

    The Woods model for the 15's would be a drive over. The deck weighs close to 500 lbs and would be very stubborn about sliding in from the side. Woods did have .pdf parts manuals for their equipment...
  76. Replies
    34
    Views
    6,320

    Re: 650G - Burning through plugs!

    Is the float level correct? Too much fuel in the bowl will cause mixture problems.
  77. Replies
    1
    Views
    1,292

    Mowing Re: 7264 PTO / mower not working

    You might be able to download the owners manual from the CC site if you have the serial number. You did engage the PTO levers? There should be one for the mid and a separate one for the rear.
  78. Replies
    3
    Views
    4,695

    Re: Filter's for the 2015

    Interchange for the Wako 150s is very rare and probably not advisable. The Wako has a brace on the inside of the can that runs full circle. The one supposed interchange I have seen did not have...
  79. Replies
    6
    Views
    1,374

    Re: 2615 HST and post hole digger????

    I have the Speeco on my 7205 Cub/2015M and there is no problem. It is at least a foot off the ground at full lift. You should be able to adjust the downlinks to control the clearance. The only time...
  80. Replies
    6
    Views
    1,150

    Re: glo plug 4110

    Sure sounds like a dead glow plug(s)to me? Check with ohm meter. You need around 1 ohm.....
  81. Re: What are all the fluid filter sizes for a 2615?

    I think it might be unwise to use anything but the OEM HST filter. The OEM has an interal rib for strength. The aftermarket types (a rare interchange) I have seen do not.
  82. Re: Does Mitsu hydraulic screens have a NAPA part #?

    Nice pix...Looking at those reminded me why I buy Mitsu products. Heavy duty!
  83. Replies
    28
    Views
    3,847

    Re: 3215 diff lock not working (Popping)

    When engaging the DL, the clutch must be in and you must be stopped. If hydro the pedal must be neutral. (?)
  84. Replies
    2
    Views
    1,361

    Re: Satoh 650 G engine repair or re-power

    Make sure it is actually a rod first...People jump to conclusions too quickly when it comes to tractor noises. If it is, then check the compression. If it is good, pull the engine, drop the pan and...
  85. Re: Anyone have a 15 series that could verify steering wheel?

    I pulled the steering wheel cap and the threaded end of the shaft measures right close to 1/2", probably 13mm. Some time ago I had that wheel off and I remember that the splines were very fine. When...
  86. Replies
    9
    Views
    924

    Re: New to the club

    Totally normal....
  87. Re: 2615 gear: no shuttle; low hydraulic output

    Mitsubishi vs Daedong? I would have to go with Mitsu irrespective of some minor difference in the spec's. The chances of a long trouble free service life are probably better with the Mitsu. That...
  88. Replies
    12
    Views
    2,037

    Tractor Sizing Re: Box Blade Size for 7304

    [QUOTE=777777]Hi Outlander,

    Thanks for the advice. Will hold off on loading the tires for now and get the 5' box blade and see how it goes.

    How did you attach an ATV blade to your loader. That...
  89. Replies
    12
    Views
    2,037

    Tractor Sizing Re: Box Blade Size for 7304

    If this is a long term tractor I would sure look at wheel weights as opposed to CalC. I would probably question whether the loaded tires would make a huge difference pushing snow anyway.. 4 link...
  90. Replies
    6
    Views
    3,170

    Re: Mitsubishi tractor Question?

    I think it is a MT300 too. K3M engine?
  91. Replies
    12
    Views
    2,037

    Tractor Sizing Re: Box Blade Size for 7304

    Eventually the CC will get your rim. I have been around many tractors since WW2 and when those tires are loaded with CC the clock is ticking......Sooner or later there WILL be a leak.
  92. Replies
    4
    Views
    1,166

    Re: 7265 cooling issues please help!

    There might be a block drain plg on the right side around the oil filter. Loosen that a tad and let it flow. That should clear the air. My 7205 has that setup... not sure about the 65.
  93. Replies
    62
    Views
    12,520

    Re: I should be happy, but I'm not.

    Too many negative waves....I think the voice in your head is saying NO! Best to heed.......
  94. Replies
    87
    Views
    15,971

    Re: Made in China

    Sage advice.
  95. Replies
    17
    Views
    2,591

    Snow Equipment Owning/Operating Re: Snow Removal Setup /Comments?

    4 link ladder chains with cleats should be quite sufficient. My tires are thankfully not loaded and the Lake Erie snow belt has yet to stop me. My drive is small, just over a tenth of a mile and I...
  96. Replies
    13
    Views
    4,687

    Re: Easy and cheap way to plow snow

    Please tell me that is NOT a GTX?
  97. Replies
    5
    Views
    1,128

    Re: Extensive Smoke on Startup

    My Cub presently does the same thing and it is a bad glow plug...AGAIN!
  98. Replies
    12
    Views
    10,866

    Oil & Fuel Re: Mahindra Diesel Engines

    Remember the 15's are not Mahindra at all except for the decal. They are Mitsubishi through and through...This is a good thing.
  99. Replies
    7
    Views
    1,516

    Price Check Re: Pricing on 2015HST

    Ummm where might that machine be located??
  100. Replies
    12
    Views
    2,109

    Re: My new 2415 has a problem...

    Be sure to get the outer and the inner. Quite often when the inner breaks it is the fault of the outer.
Results 1 to 100 of 136
Page 1 of 2 1 2
© 2017 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.