Search:

Type: Posts; User: J_J; Keyword(s):

Results 1 to 100 of 5000
Page 1 of 50 1 2 3 4

Search: Search took 0.44 seconds.

  1. Replies
    1
    Views
    375

    TIRES 20X10X8 with rim

    20x8.00-10 4 BOLT WANDA P332 WHEEL TURF TIRE ASSEMBLY
  2. Replies
    10
    Views
    1,261

    Re: John Deere 2520 bucket will not lift

    Just unplug and replug.

    Your QD could be bad and not usable.

    Check it out by removing the QD and use union couplers.

    You can also remove the hose off the cyl and see if fluid is passing...
  3. Replies
    10
    Views
    1,261

    Re: John Deere 2520 bucket will not lift

    Unplug and reset the QD's.
  4. Replies
    2
    Views
    406

    Re: do I need a pressure relief?

    Your valve relief is on the pump side or IN port side of the valve.

    It is there to protect the pump.
  5. Replies
    29
    Views
    2,255

    Re: Need help solving snow plow problem

    I believe there were some FEL valves maybe Kubota, that had full time regen on the FEL valve.
  6. Replies
    29
    Views
    2,255

    Re: Need help solving snow plow problem

    Move the lever past the regen mode, which is the first part of lever travel. Dump mode is far right.

    There is no flow to the cyl when using regen.
  7. Replies
    6
    Views
    739

    Re: need help adjusting relief pressure at spool

    Yes, but only momentary.
  8. Replies
    6
    Views
    739

    Re: need help adjusting relief pressure at spool

    Install a 3000 psi hyd gauge in a tee and install it in the IN port of the valve in question.

    If the relief valve uses shims, install the shim pkg. Engine off.

    Use the valve lever to fully...
  9. Replies
    113
    Views
    7,892

    Re: Could air cause this issue???

    If there is a plug in the PB port, then the tank/OUT port should be going to tank.

    If your hoses from the log splitter is feeding any other hyd function downstream, then you should be using the ...
  10. Replies
    113
    Views
    7,892

    Re: Could air cause this issue???

    Each spool has a load check.

    LOAD CHECK (Sometimes called lift-check). This is a feature which will keep a given load from dropping as the control valve
    spool is being shifted until the inlet...
  11. Replies
    27
    Views
    2,145

    Re: need help choosing hydraulic pump

    A cement mixer should not turn no more than 30 to 50 rpm.

    Torque is good. You have plenty of HP to turn the mixer.

    If I remember right another TBN member used a 3.0 cu in motor and then...
  12. Replies
    113
    Views
    7,892

    Re: Could air cause this issue???

    He has stated that the the IN port and the OUT port are functioning correctly.

    He has not connected two hoses, without QD's to the same spool and placed the hoses in a bucket and verified that the...
  13. Replies
    27
    Views
    2,145

    Re: need help choosing hydraulic pump

    You would run out of HP and the engine would stall.

    17 GPM need 33.1 HP.
  14. Replies
    9
    Views
    1,010

    Re: Tricks for finding suction-side air leak?

    Just use thick grease on all suction parts.
  15. Replies
    27
    Views
    2,145

    Re: need help choosing hydraulic pump

    17 GPM at 2000 psi using 22 HP.
  16. Replies
    27
    Views
    2,145

    Re: need help choosing hydraulic pump

    Your 22 HP can turn a 11.3 GPM pump at 3000 psi.
  17. Replies
    27
    Views
    2,145

    Re: need help choosing hydraulic pump

    What you are looking for is torque, and rpm.

    Rpm should be low to med.

    The larger cu in, the larger the torque.

    If your pump can supply 10 GPM and has a capability 3000 ps, you can drive a...
  18. Thread: Hydraulic pump

    by J_J
    Replies
    15
    Views
    1,452

    Re: Hydraulic pump

    You are so right.

    I did not refresh the page for the correct answer.
  19. Replies
    113
    Views
    7,892

    Re: Could air cause this issue???

    Apparently we do not have the whole story.

    If you have a DA valve connected to a single DA cyl, and you push the lever, the cyl is going to move. If it does not, suspect the QD. or get rid of the...
  20. Replies
    25
    Views
    1,930

    Re: Links please for hooking up a FEL grapple

    I recommend you get either a 3rd function valve, or a diverter valve and control it using the curl function on the FEL valve.

    The 3rd function valve is added to the PB line from the FEL in series...
  21. Replies
    9
    Views
    882

    Re: DIY 3rd function valve for kubota L39 HELP?

    Northman Fluid Power Hydraulic Directional Control Valve 26.4 GPM, 4500 PSI, 3-Position, Double Solenoid, Open Center Spool, 12 Volt DC Solenoids, Model# SWH-G03-C3-D12-10 | Power Solenoid|...
  22. Thread: Hydraulic pump

    by J_J
    Replies
    15
    Views
    1,452

    Re: Hydraulic pump

    That is a multi sectional hyd pump.

    The cu in capacity is probably different for each section.

    Based on the size of the ports, it probably will pump lots of GPM.

    Problem is, can your engine...
  23. Re: Installing 3rd Function Hydraulics - Electric over Hydaulic

    CHIEF Solenoid Operated Directional Control Valves

    D03 Subplate Manifolds

    Northman Fluid Power Hydraulic Directional Control Valve – 26.4 GPM, 4500 PSI, 3-Position, Double Solenoid, Tandem...
  24. Re: Installing 3rd Function Hydraulics - Electric over Hydaulic

    CHIEF Solenoid Operated Directional Control Valves
    ...
  25. Re: Installing 3rd Function Hydraulics - Electric over Hydaulic

    What is the pump flow on the L39?
  26. Thread: 4n1 Bucket/Arm

    by J_J
    Replies
    5
    Views
    997

    Re: 4n1 Bucket/Arm

    If the high flow valve is solenoid operated, the pump will run at max or engine rpm. He could reduce the engine rpm.

    If you put restrictors in line, the unrestricted flow will pass over the...
  27. Re: Weird Hydraulic Leak with Flushface Skid Steer Quick Disconnects

    As I stated earlier, you have to read the specs for what you want.

    When you ask for QD's, the dealer will provide you with what he has in stock.

    If you want connect under pressure and no...
  28. Replies
    12
    Views
    1,963

    Re: Loader Pressure Release

    If you want to connect under pressure, then get the QD's that allow that.

    If not, you have to make a dummy connector that relieves the pressure on the implement.

    Sometimes the weight of the...
  29. Replies
    72
    Views
    5,888

    Re: Diverter Sanity Check

    Valves that have regen, you simply go past regen to the power mode or those valves with regen to the far right, don,t go there.

    The reason it will not work in regen is that the tank port is...
  30. Re: Weird Hydraulic Leak with Flushface Skid Steer Quick Disconnects

    Some flat face couplers will connect under pressure.

    Do a search and find the correct coupler for your application.

    Parker IP coupler will connect under pressure.
  31. A larger pump will use more HP. Do you know...

    A larger pump will use more HP.

    Do you know the specs on your current pump?

    Look for a pump with larger cu in capacity and the shaft and mounting holes match.

    Do you have enough HP?
  32. Replies
    6
    Views
    1,186

    Re: jd 420 loader will not stay in float position

    It could very well be moisture related, as the moisture will freeze and jam up the parts.

    Disassemble, clean and lube.
  33. Replies
    6
    Views
    1,186

    Re: jd 420 loader will not stay in float position

    Remove the cans on the bottom of the FEL valve and inspect the springs, ball bearing and the groove for the float.

    Clean or replace any damaged part, and then lube well.

    Make sure the weep...
  34. Replies
    31
    Views
    3,887

    Re: Quad tires for PT Tires

    This is my cache of tires.
  35. Replies
    31
    Views
    3,887

    Re: Quad tires for PT Tires

    26 IS DIAMETER

    12 WIDTH OF TIRE

    12 IN RIM
  36. Replies
    17
    Views
    2,858

    Re: Just rebuilt Tram pump

    You can almost bet that your wheel motors leak some and the charge pump keeps the fluid constant in the hyd circuit .

    I actually have case drains on my 1445 to pass the fluid to the pump and back...
  37. Replies
    13
    Views
    1,912

    Re: MERRY CHRISTMAS EVERYONE

    Actually, I have been laying back and watching, and my health is fair for being 75.

    There are a lot of intelligent people here , more knowledge than I, and so I thought I would let them answer...
  38. Replies
    17
    Views
    2,213

    MERRY CHRISTMAS EVERYONE

    I hope you all get all the toys you ask for.

    May you also have a very good New Year.
  39. Replies
    13
    Views
    1,912

    MERRY CHRISTMAS EVERYONE

    I hope you all get all the toys you ask for.

    May you also have a very good New Year.
  40. Replies
    34
    Views
    4,585

    Re: 10 Hours later . . . an update

    Wet rubber does cut better. I thought everyone knew that.

    Dry rubber does not cut as well. I thought everyone knew that also.

    Cut rubber is not good unless you need it cut.

    Dry rubber is...
  41. Replies
    3
    Views
    699

    Re: Deere 655 SCV won't move

    Check your QD's as the pressure might try and close the ball and spring preventing fluid from moving.

    If you move it slow, less pressure might not move the spring and ball and let fluid pass.
    ...
  42. Replies
    6
    Views
    942

    Re: adding a montana loader to a kubota b9200hst

    I also have a B-9200HST.

    HYD BLK # 4 goes to the FEL valve IN port.

    HYD BLK# 5 goes to FEL PB adapter.

    HYD BLK# 6 goes to FEL OUT/tank port.

    Be sure to turn the screw clockwise.
  43. Replies
    34
    Views
    4,585

    Re: 10 Hours later . . . an update

    If you want to cut rubber, use a 7 in blade with the teeth ground off and then sharpen the blade and then wet the rubber.

    Wet rubber cuts better when wet.
  44. Thread: New hydraulics

    by J_J
    Replies
    6
    Views
    1,126

    Re: New hydraulics

    Using a 3rd function valve, you can do three functions at the same time if you only use half pump flow for the FEL.

    The other half of pump flow can be used for the 3rd function valve.

    If you...
  45. Thread: Will it work?

    by J_J
    Replies
    26
    Views
    2,639

    Re: Will it work?

    You mean that I can not make an open center valve into a CC valve by using a PB adapter and a plug, or a CC plug.

    Da*****, I sure thought I could, and please explain why it will not work.
    ...
  46. Thread: Will it work?

    by J_J
    Replies
    26
    Views
    2,639

    Re: Will it work?

    Do you know for sure that the FEL valve is strictly a CC valve?

    I simply said that if the valve is convertible what was necessary to convert the valve.

    He is asking about the valve on the FEL...
  47. Thread: Will it work?

    by J_J
    Replies
    26
    Views
    2,639

    Re: Will it work?

    If the valve is PB capable, and used on CC system, the valve will need a PB adapter and a plug, or a CC plug, which is longer.

    Show pic of valve , all sides if possible. Also indicate any markings...
  48. Replies
    17
    Views
    1,925

    Re: Directional vs Diverted valve

    The price is about the same, less than $200 plus hoses and fittings.

    You have to add the subplate to the solenoid valve also.
  49. Replies
    44
    Views
    4,359

    Re: FEL seems weak- how to check

    Of course not. 90 degrees is the angle that the cyl maximum force is achieved.

    That's a why I put the angles in there.

    The angle is changing as you lift
  50. Replies
    44
    Views
    4,359

    Re: FEL seems weak- how to check

    A FEL with a good pump will never lift at max cyl capacity.

    The cyl is always at an angle, and gets worse with lift.

    Probably starts at 45 to 65 degrees and decreases as you lift.

    Best...
  51. Replies
    3
    Views
    649

    Re: bypass/disable 3 point lift?

    There is a neutral position where the 3pt valve has little or no pressure.

    Try the lever in the middle of the action.

    If you had a hyd gauge installed, you could see when the 3pt was activated.
  52. Thread: Will it work?

    by J_J
    Replies
    26
    Views
    2,639

    Re: Will it work?

    Your FEL cylinders do not care which type valves supplies the fluid.

    If in fact the new FEL has open center valves, they might be convertible valves, where you simply add a Closed Center plug to...
  53. Replies
    185
    Views
    35,397

    Re: Firewood Gathering With A Power Trac

    You are here. Start posting.
  54. Replies
    16
    Views
    1,000

    Re: what type if hydraulic system does my rig run? ?

    A pump flow test will determine if the pump is putting out the advertised GPM's .

    The pressure test will determine if the pump can maintain the pressure developed by the hyd component.

    You need...
  55. Replies
    16
    Views
    1,000

    Re: what type if hydraulic system does my rig run? ?

    Hydraulic motor HP is determined by the torque and speed.

    If the motor is working at full potential, it should do the intended job.

    If the pressure is not developed by the motor and GPM's...
  56. Replies
    9
    Views
    629

    Re: Do the hydraulics seem kind of wimpy?

    You will probably not be able to lift wheels in regen mode.

    Use the dump power mode, to the far right.

    You can also lift the bucket and tilt down, then use the lift arms to raise the wheels.
  57. Re: Anybody use flow control of 4 in 1 bucket close, when using solenoid open/close?

    There is no reason that you can not use use a needle valve to adjust the flow using an electric valve.

    Some needle valves have flow control in one direction and others have flow control in both...
  58. Replies
    7
    Views
    810

    Oil & Fuel Re: Rough Idle - Carb Issue

    Do you have a fuel filter in the fuel line?
  59. Re: Ouch! Replace Nimco 2S-40272 Loader Ctl. Valve w Brand LV22 / Surplus Ctr. 9-7401

    Spools are fitted to a specific bore, and and no replacements are made for that bore.

    A good craftsman might be able to machine a bore and fit a spool, but unlikely.

    When a spool starts...
  60. Replies
    9
    Views
    576

    Re: mahindra 3016 adding remotes

    Yes, that is correct.
  61. Replies
    8
    Views
    534

    Re: 3rd unction valve or diverter valve?

    If you only use partial lever on the FEL, you can then use the 3rd function valve.

    The 3rd function valve speed of operation will be dependent on the GPM flowing through the 3rd function valve.
    ...
  62. Replies
    9
    Views
    576

    Re: mahindra 3016 adding remotes

    Remove the tee from the PB line.

    Add a female QD to the hyd block PB out. Plug your log splitter in there. No 3pt available.

    Add a male QD to the 3pt metal line, and then when you remove the...
  63. Replies
    39
    Views
    3,264

    Re: Hydraulics and heat

    If your attachment is closed center hyd system, and your tractor is open center hyd system, you will have problems, as the flow in an open center hyd system has to flow all the time. A closed center...
  64. Replies
    9
    Views
    576

    Re: mahindra 3016 adding remotes

    The PB outlet with adapter from any valve goes to the next valve IN port throughout the hyd flow path.

    All valves in an open center hyd system are connected this way.

    Your flow pat should be...
  65. Replies
    9
    Views
    576

    Re: mahindra 3016 adding remotes

    All valves should be in a series flow path.

    No tee's in open center hyd systems, except tank lines.
  66. Thread: M7060 Hydraulics

    by J_J
    Replies
    5
    Views
    413

    Re: M7060 Hydraulics

    Some hyds valves have SA detent and others have a DA action detents which are pressure activated.

    If your valve is kicking out of detent, then you have a pressure detent release valve, similar to...
  67. Replies
    13
    Views
    832

    Re: Need help with front loader lift

    Reset the QD's
  68. Replies
    185
    Views
    35,397

    Re: Firewood Gathering With A Power Trac

    You could use a wheel motor and large blade.

    Use a 14 to 24 in carbide blade.

    http://www.wikco.com/images/saw16.jpg

    High Torque Tree Saw Attachment for Skid Steers
    ...
  69. Re: deere 2520 with Bradco Trencher Hookup Question

    A lot of open center valves come from the manufacturer with the PB port plugged and therefore the total flow goes through the OUT port.

    If a valve with PB has the adapter installed, that separates...
  70. Re: deere 2520 with Bradco Trencher Hookup Question

    I don't think you have a complete path for everything to work correctly.

    I believe the plug with spring and poppet is a load check valve.

    If you are going to use PB, then you need an adapter...
  71. Replies
    11
    Views
    988

    Re: Source for hydraulic cooler fan

    Put a hair dryer or heat gun on the thermal switch.
  72. Replies
    31
    Views
    2,178

    Re: Using old boat trim/tilt hydraulics on a tractor.

    I have a small hyd systems for boats that am using.

    I use it on my pull behind scraper blade to raise and lower the blade for transport.
  73. Re: Massey 135 Hydraulics issues with Log Splitter

    If your log splitter valve is in series with the hyd flow including the 3pt, you still have flow to the 3pt and if the 3pt is not centered, it will move accordingly.

    If the 3pt is in neutral, the...
  74. Re: Where can I find information on older Cessna control valves?

    Does it look anything like these?

    Surplus Center
    ...
  75. Thread: Bucket won't curl

    by J_J
    Replies
    10
    Views
    586

    Re: Bucket won't curl

    If he is getting relief pressure, and the cyl rod is not moving, it has too be the QD.
  76. Replies
    24
    Views
    676

    Re: Second rear remote crossover

    To check for leakage, remove the work port hoses with valves in neutral, and there should be no flow.

    If fluid comes out the work ports, the valve might not be centering correctly or the spools...
  77. Replies
    24
    Views
    676

    Re: Second rear remote crossover

    It might have both system.

    DK50SE

    Hydraulics
    Hydraulics
    Collapse
    Maximum Pump Flow: 16.8 gpm (63.9 l/min.)
    Hydraulic System: Standard: Open center with up to 3 rear mechanical valves
    Twin...
  78. Replies
    24
    Views
    676

    Re: Second rear remote crossover

    Did you check and reset the relief pressure on the new valve?.

    Most relief are set the same as the tractor relief setting.
  79. Replies
    2
    Views
    367

    Re: hydraulic circuit, need advise

    Circuit looks OK.

    You can just plug the PB port and the pump flow and cyl flow will pass through the OUT port.
  80. Replies
    1
    Views
    234

    Re: TC45DA curl/dump/regen issue

    If you have a regen spool, you also have parts outside the valve under the caps on the bottom of the valve.

    Remove the can covers and inspect the parts for broken or misaligned parts.

    You might...
  81. Replies
    2
    Views
    263

    Re: MF 1533 FEL Hydraulics Stuck

    If you have QD's, reset them.
  82. Re: replacing 5 valve bank with a three valve and a 2 valve bank connected

    Pressure is based on the load on the cyl or hyd motor.

    Light load will show low pressure and heavy load will show high pressure.

    If you can't lift a load, the valve relief is relieving and the...
  83. Replies
    40
    Views
    1,586

    Re: Valve screwing with my head

    Should work.
  84. Replies
    40
    Views
    1,586

    Re: Valve screwing with my head

    To pump 60 GPM at 3000 psi you need 116 HP.

    What engine do you have in mind?
  85. Replies
    40
    Views
    1,586

    Re: Valve screwing with my head

    You will need a splitter that will divide the pump supply for the hyd motor.

    Something like this with a 60 GPM capacity.

    Divides the flow into two equal paths.

    This valve is only 8 GPM. ...
  86. Replies
    40
    Views
    1,586

    Re: Valve screwing with my head

    With 60 GPM running through this valve,you are going to have some really fast cyl.
  87. Replies
    40
    Views
    1,586

    Re: Valve screwing with my head

    Since the valve has PB installed, the flow path is IN port to PB port in neutral.

    When you shift the lever to run the motor, you are diverting some or all of the pump flow to a work port.

    The...
  88. Replies
    40
    Views
    1,586

    Re: Valve screwing with my head

    To test if the spool is a motor spool, you have to connect a coupler hose to simulate a hyd motor on the work ports, and when you do that and blow air through the IN port, the air will now exit the...
  89. Replies
    40
    Views
    1,586

    Re: Valve screwing with my head

    I would suggest that the red plugged port is the IN port as that looks like a relief port in the end cap.

    Where are you seeing a PB adapter or port.

    Can't see the side ports if any.
  90. Replies
    26
    Views
    1,029

    Re: front loader question

    A 3rd function valve connected to the jaw cyl should open/close and lock in place with no voltage

    If your valve was capable of multiple lever action, it should still work.
  91. Replies
    26
    Views
    1,029

    Re: front loader question

    I suspect you have restrictors in the loader.

    Logic says that you should have more flow at higher rpm, and therefore more speed
  92. Thread: 3pth Log Splitter

    by J_J
    Replies
    1
    Views
    337

    Re: 3pth Log Splitter

    Your kickoff pressure is adjustable.

    Install a hyd gauge and test it.
  93. Re: case ih dx35 3 point arms low on lifting power/

    Don,t know if your tractor is open center or closed center, but a hyd gauge in the pressure line should read 0 psi to a low pressure for open center hyd system and standby pressure for a closed...
  94. Re: Strange Grapple Behavior - Question on Hooking Up

    A 3rd function valve is connected to the PB, and a diverter valve is connected to the curl circuit.

    If no hyd function, check your wiring.

    It could also be a stuck solenoid.
  95. Re: replacing 5 valve bank with a three valve and a 2 valve bank connected

    The relief valve will come set to a certain pressure.

    Once installed, and gage installed, turn the screw until tractor specs is set.

    You can install the pressure gauge in a tee, anywhere in...
  96. Re: replacing 5 valve bank with a three valve and a 2 valve bank connected

    If you have a closed center hyd system, all valves are in parallel.

    No PB is used, and a closed center plug goes in the PB port.
  97. Re: Are PT 425 Owners happy with the PT Stump Grinder??

    My thoughts on the rotation is this.

    If the bottom of the blade is turning toward you, you should be cutting on the backside of the stump, so as to throw the chips forward. That also means that...
  98. Re: Installed new hydraulic hoses now t n t not working

    I believe one A port and one B port go to a single cyl.

    Remove all hoses to cyl and activate each function momentarily and you will see what is correct.

    One restrictor per cyl .
  99. Replies
    4
    Views
    494

    Re: Restoring lost prime in hydraulic pump?

    It is hard to say where that bearing came from, could be from a check valve assembly.

    I would recommend a parts manual. You probably need one anyway.
  100. Replies
    4
    Views
    581

    Re: Installed a new Hydroback cable

    Did instructions come with the Hydraback?

    Terry told me how to adjust the Hydraback years ago. I forget all the steps now.
    ...
Results 1 to 100 of 5000
Page 1 of 50 1 2 3 4
© 2016 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.