Search:

Type: Posts; User: Leejohn; Keyword(s):

Results 1 to 100 of 3300
Page 1 of 33 1 2 3 4

Search: Search took 0.13 seconds.

  1. Replies
    1
    Views
    104

    Re: Renaul hidraulic problem

    Welcome!! What is wrong with the hyd's? A manual might be hard to find.
  2. Replies
    37
    Views
    2,150

    Re: Fixing Aluminum Canoe

    When you see sparks fling from aluminum boat when cutting it in half, you better not believe any part of the BS.
  3. Replies
    6
    Views
    636

    Re: Kubota B2620 loader valve disassembly

    Put in N and blow air into the work port and see if anything comes out.
  4. Replies
    4
    Views
    326

    Re: 2 Cycle Carburetor - No High/Low Markings

    The screw nearest to the engine is the slow speed.
  5. Re: Anyone want to re-sharpen drill bits again......

    With the youtube videos, if they have there rubber gloves on don't waste your time watching.
  6. Replies
    37
    Views
    2,150

    Re: Fixing Aluminum Canoe

    Cut the end off and make a square stern out of it.
  7. Replies
    8
    Views
    905

    Re: b7800 will not turn over with the switch.

    I have the seat switch bypassed. The clutch switch has always worked, but the pto one has now and then acted up. The hst. peddle gets a stick in it sometime and after it is removed has always worked....
  8. Replies
    12
    Views
    2,427

    After psi check and if ok, then check cyls for a...

    After psi check and if ok, then check cyls for a loose or piston came off rod.. Doesn't sound like you need a new valve.
  9. Replies
    12
    Views
    2,427

    Re: help- husco 9210 control valve

    What is bad with the valve?
  10. Replies
    244
    Views
    72,795

    Re: any toro groundsmaster fans on here?

    I just got done working on a 325 that was in a flood. Set for about a 4 or 5 weeks before I got it. Had to go thru everything and put all new bearing and seals in the deck and had to cut a lot of the...
  11. Replies
    10
    Views
    2,321

    Re: Splitting A Kubota GL4240HST 4WD

    Quote: I may have missed it - but is the 4WD output shaft seal leaking as well? If you replace the seal there, the 'seal & collar' need to be replaced as a pair. Those wear collars with the rubber...
  12. Replies
    10
    Views
    2,321

    Re: Splitting A Kubota GL4240HST 4WD

    Not sure, all I remember is it had a 10MM head and fine threads.
  13. Replies
    34
    Views
    3,886

    Re: Kubota Top-N-Tilt concerns

    I was ?ing the rod size for a cat2 tractor. That only looks to be 1".
  14. Re: I'm doing something wrong with this drawbar right?

    I got my hair pin on the bottom. With hair pin on top and it gets pulled out there goes the pin and draw bar. At least you get a 2nd chance to save the pin and bar.
  15. Replies
    25
    Views
    1,075

    Re: Lincoln 1142 grease gun won't prime

    My dad gave this when I was 3 years old (1943) and I knew right then what my job was going to be until I moved out. Never had to prime it, so have no ideal all the trouble you guys are having with a...
  16. Replies
    541
    Views
    277,317

    Re: Show What Tool You Made*

    I bet that works real good.
  17. Replies
    16
    Views
    1,880

    Re: Tired of banging my head on this thing!

    Sounds like the top link mount on the carry all is to high. Should be around 15 to 16" up from the bottom link pins. Show a picture of the carry all hooked up to the tractor.
  18. Re: Anyone know where I can buy brass 1" barbed Tee's and 90's fittings?

    try FS farm supplys
  19. Replies
    13
    Views
    1,032

    Re: Will this end cap work?

    Just search cross mfg.
  20. Replies
    541
    Views
    277,317

    Re: Show What Tool You Made*

    I like that ideal!!!
  21. Replies
    13
    Views
    1,032

    Re: Will this end cap work?

    Make sure the relieve valve is not stuck open in the control valve.
  22. Re: Homemade 6 wheel drive cart- problems, please help!

    I would get the psi up to at least 2100.
  23. Re: Here is the correct part that needs to be identified please :)

    In one picture it looks like the head of the bolts might be broken off and someone made the bracket to hold the roll over bars on. If so I would replace all with a harder bolt. Do you know if the...
  24. Replies
    8
    Views
    378

    Re: Front loader problem

    Like said before the load checks stuck open and it could be that it doesn't even have any. Show a picture of the valve.
  25. Re: Hyd Cylinder keeps squirting oil out bolt head when in lift

    The end should have a vent there. Oil coming out there is telling you the seals are bad on the cyl.
  26. Replies
    33
    Views
    1,261

    Re: Log splitter Problem

    Make sure the pump pressure line is to the in port of the valve. Before I would change pumps I would change the valve.
  27. Replies
    175
    Views
    8,408

    Financing Re: Issue(s) getting financed?

    I don't get it either! This is like me saying, "You should of seen what I did yesterday and then everyone telling me what they did." I see this stuff on a place that's called face book or something...
  28. Replies
    14
    Views
    1,521

    Re: B3030 vs. B3300SU

    I would go with the B3030 it was top of the line of the B's. Also I would not buy a tractor without a loader. I have the B7800 and was the cheaper step down from the 3030. It did not have all the...
  29. Replies
    14
    Views
    1,627

    Re: hose orientation with two 90's

    Just have this fitting put on the hose when you order the hose. FJX90-06-06 | 3/8" Hose x 3/8" JIC Female Swivel 90
  30. Replies
    34
    Views
    2,824

    Re: Help me catch Houdini Coon

    Get a auto door and put it on a timer.
  31. Replies
    13
    Views
    1,400

    Rotary Cutter Re: Help me find the right slip clutch

    Check this out. PTO Shaft, PTO Parts, PTO Adapter, PTO Power Take Off, Eurocardan
  32. Replies
    13
    Views
    3,458

    Re: Front End Loader Hydraulics,

    Try putting taking the tractor out of gear to get the front up. If you have the 1 3/4" cyls you might not be able to with it trying to pull the tractor fwd.
  33. Replies
    2
    Views
    971

    Re: No Hydraulics 4630 New Holland 1979

    Let the 3pt down just a little, your feed back adjustment might be off. Feel the line with your hand and see if you can feel oil going thru them. Also at the same time see if any hose moves when...
  34. Replies
    16
    Views
    2,384

    Re: New Machine For Hillside Mowing

    This thing I think could mow just about any hill. I know this isn't what you want, just thought you might enjoy watching. Brielmaier motormaaier op afstandbediening met Carroy.mp4 - YouTube
  35. Re: Are these pole barn trusses defective, or are they okay to use?

    I would send them back, they should of not even come out of the plant like that.. When I pay for something with a good check I want what ever it is to be good.
  36. Replies
    1
    Views
    1,366

    Re: Tafe 35di hydraulic lift

    Take the cups at the end of that spool off. It sounds like some broken parts inside of the cups. Watch for broken springs and if it has float watch for small steel balls (2 or 3).
  37. Re: Kubota L2501. Adding front and rear remotes

    I run a grabber and tree puller off the front remotes . On the back I have hyd top link and other stuff I run off the rear remotes. I only have one set in the back and just unplug my top link. I use...
  38. Thread: Screen Filter

    by Leejohn
    Replies
    4
    Views
    1,638

    Look at these Strainers | Hydraulic Filters |...

    Look at these Strainers | Hydraulic Filters | Hydraulics | www.surpluscenter.com
  39. Replies
    3
    Views
    1,025

    Re: Tractor rpm problems

    Check vent on fuel tank.
  40. Re: Kubota L5240 Hydraulic leak...need help please

    Check this thread http://www.tractorbynet.com/forums/owning-operating/372943-splitting-kubota-gl4240hst-4wd.html?highlight=
  41. Re: Kubota L5240 Hydraulic leak...need help please

    Yes tractor has to be split, it's coming from the engine drive shaft seal or gasket at the trans or from the 4wd shaft seal at the trans.
  42. Replies
    7
    Views
    1,258

    Re: My 3 PH carry all

    Hyd top link well make it dump.
  43. Replies
    11
    Views
    1,785

    Re: Putting two cylinders into the same remote

    Adding a 2nd remote valve should not cost $1800.00. I would guess more like $400.00 max.
  44. Re: KUBOTA 3RD. Remote Hydraulic Controll - Installing direction solenoid valve

    I looked to see if I had a parts manual and I didn't. It just seems like there should be a better place to tap into the system.
  45. Re: KUBOTA 3RD. Remote Hydraulic Controll - Installing direction solenoid valve

    One more thing. When unscrew the bolts that holds it all together you have 9 o rings to get back right. I would pull the seat and pan under it, and that seat is heavy.

    I just went back and looked...
  46. Re: KUBOTA 3RD. Remote Hydraulic Controll - Installing direction solenoid valve

    I'm going to do some guessing and if'n. If you look there are 3 holes with o rings in each spool until you get to the end cap. Now "if" that end cap has a plug in it as it looks like it might and...
  47. Re: KUBOTA 3RD. Remote Hydraulic Controll - Installing direction solenoid valve

    When one of the 3rd manual valves is actuated is the By port blocked off? I.e. Does the flow go from P - through work cylinder- back to tank T?

    Yes if you open all the way, if only half open the...
  48. Re: KUBOTA 3RD. Remote Hydraulic Controll - Installing direction solenoid valve

    Your tractor is open center and you need the by fitting for it to work. The T port well then be the return for the work ports only.
  49. Re: This should be something easy for y'all. Hydraulic cylinder re-seal

    It's Case/international now, try the Case Dealer or stop by a hyd shop and they should be able to fix you up with the seals.
  50. Replies
    16
    Views
    2,384

    Re: New Machine For Hillside Mowing

    Man that is a lot of land to be mowing with a 48" mower. I would have 2 mowers the 48 for trim and a larger one for the rest.
  51. Replies
    157
    Views
    12,791

    Re: Advice from the voice of EXPERIENCE !!

    Did you guys read the title of the thread? EXPERIENCE !!
  52. Replies
    36
    Views
    8,502

    Re: John Deere 2520 bucket will not lift

    I knew he could get you all fixed up. Sometimes it's best for just one on one to get things fixed.
  53. Replies
    157
    Views
    12,791

    Re: Advice from the voice of EXPERIENCE !!

    Don't try and dump a dump trailer going down hill hooked to the 3pt. Use the draw bar.
  54. Replies
    12
    Views
    2,097

    Re: Kubota B8200HST. Loses drive power.

    With you just getting the tractor, I would go ahead and do the full service on the hyd system. Your 1st guess.
  55. Replies
    36
    Views
    8,502

    Re: John Deere 2520 bucket will not lift

    I said what I said because this is what you wrote. I replace the female side and nothing changed. Then I switched the lift (black) with the curl (blue) and lift still doesn't work and curl does<(
    ...
  56. Replies
    36
    Views
    8,502

    Re: John Deere 2520 bucket will not lift

    Roy it sounds like she only switch one hose not the pair.
  57. Replies
    22
    Views
    7,033

    Re: Kubota rear hydraulics

    Didn't Kubota just build or building a new place some where here in the US?
  58. Replies
    14
    Views
    3,519

    Re: Kubota loader becomes anemic when hot

    If your feed back adjustment is off and with the 3pt is up you are heating the hyd oil way up. Look in your manual for the info on how to adjust it.
  59. Thread: Rear remotes.

    by Leejohn
    Replies
    3
    Views
    1,233

    Re: Rear remotes.

    Read this thread http://www.tractorbynet.com/forums/hydraulics/380497-ts110-new-holland-woods-bw180xhd.html
  60. Re: Any guess what could the problem with this new xr4155

    On the steering I think it's a bad or not adjusted priority divider valve. The engine you need to check the fuel shut off valve, crack one of injector line and see if there is fuel there, next the...
  61. Replies
    17
    Views
    2,723

    Rear Finish Mower Re: Help with 3 pt set up on finish mower

    That still well be to long. You sure don't want to mess up the PTO on the tractor. A quick hitch and remove the clutch would maybe do it. A finish mower with belts doesn't need a slip clutch. Do a...
  62. Replies
    9
    Views
    728

    Re: Largest finishing mower on l3560?

    I was running my woods 990 with a L3130 before my L4240. It did just fine and I mowed 20A at 5mph.
  63. Re: Help running Single Acting Cyliner on Dual Remotes

    If the hyd block was used to plumb the remote. Look under your right side floor right under foot. There is a hyd block with a valve that you can turn to give you pressure back there. It takes a...
  64. Replies
    15
    Views
    1,262

    Re: Rear end popping

    I had a popping in my 4240 sounded like lug bolts. I found out it was the front axle pivot was loose.
  65. Re: TS110 New Holland and Woods BW180XHD Batwing Hydraulic Port Trouble

    By the pictures I seen woods has the hose hooked to the rod end of the cyl.
  66. Re: TS110 New Holland and Woods BW180XHD Batwing Hydraulic Port Trouble

    If you have 4 coupler on the tractor you have 2 remotes. It takes 8 couplers for 4 remote sets. 2 sets =2 levers 4 sets 4 levers.
  67. Re: TS110 New Holland and Woods BW180XHD Batwing Hydraulic Port Trouble

    You have 4 remote couplers, you can only 2 things with them. In other words you have two sets. If you have only one hose going to the wings then you have to T the lines and use 1/2 remote sets, then...
  68. Replies
    18
    Views
    4,349

    Re: Homemade Grapple

    It's a nice unit all right and he done a great job on it, but I think it's to big.
  69. Replies
    9
    Views
    2,575

    Re: What is this thing?

    A Finish Mower doesn't need a slip clutch.
  70. Replies
    22
    Views
    7,197

    Re: 3 point trailer mover video!

    Go easy when moving a 5th wheeler around with ball way up high.
  71. Re: wanting to run a 7ft planter off the FEL hydraulics

    I have a 2 spool remote kit that well fit your tractor. One spool is spring center and one is detent, it's new never been on a tractor. I don't have the mounting manual. I well sell it for $275.00...
  72. Re: Mower is acting funny, what do you think is wrong?

    You are calling the electric clutch a Electronic PTO, it's just a electric clutch and maybe it's drawing to many amps to keep it engaged in turn running your battery down. Did you check that fuse...
  73. Re: Mower is acting funny, what do you think is wrong?

    Doesn't a B&S engine run off of a mag and the battery only for starting?
  74. Re: Mower is acting funny, what do you think is wrong?

    The fuse holder is melted.
  75. Re: Help with identifying the model number of my ISEKI

    By the decal on one side of the hood that one part looks like the bottom of a G, so I would look at the TG models.
    If you haven't check here try this. TractorData.com - Farm tractors
  76. Replies
    7
    Views
    581

    Re: Diesel engine compression question.

    I thank he is wrong, it takes something around 2000 psi to open the ejectors.
  77. Replies
    11
    Views
    1,294

    Re: Ford 1920 front end loader problemf

    I also have a kubota with this same loader on it, it has 2 inputs and 1 return port on the control valve, That is not right, it has 1 input and 2 out. If you look it has IN, T , BY or PB (that...
  78. Replies
    8
    Views
    602

    Re: Box blade/ land plane ripper teeth

    Boy I hope they wear longer then what you are getting. I just put 12 on my wheeled box blade to fight the washboards on the road.
  79. Replies
    65
    Views
    4,026

    Re: Anyone still use rope to tie things down?

    I never use bungee cord, rope most of time. Big loads straps or chain.
  80. Replies
    8
    Views
    1,238

    Re: Broken BX hood tab.

    Yes, mine has been done that way on one side for over two years maybe longer. I only done one side and should do the other before it brakes.
  81. Replies
    8
    Views
    1,238

    Make a temp plate out of card board of the good...

    Make a temp plate out of card board of the good side, then cut a thin sheet of aluminum the same as your temp plate. Use small pop rivets and pop over what is left leaving room for the thumbscrew....
  82. Replies
    14
    Views
    3,519

    Re: Kubota loader becomes anemic when hot

    Could be you are sucking air after it gets warm. Check the suction line to the hyd pump. There is a small rubber hose that hooks the steel line together, check for cracks and lose clamps.
  83. Replies
    13
    Views
    1,301

    Re: FEL control issue

    Don't try to unhook the couplers, even if you can unhook them you well not get them back hooked. Just bleed it down to where you want it then drive to shop. 5 min job.
  84. Re: 2030 died while driving, now struggles to start

    Sounds like you are going to need a major overhaul now.
  85. Re: Cutter gearbox question for seasoned farmers, machinists and engineers

    One thing I forgot to say is if it's a race and cone bearing the preload has to be set. To tight it well run hot and loud, about 10 to 12 rolling in lbs.is about right Roller bearings don't need a...
  86. Replies
    1
    Views
    1,024

    Re: Front end loader vlave

    Some mfgs make a joystick kit you can get. Maybe check that out 1st.
  87. Replies
    18
    Views
    2,408

    Re: Looking for Two parts

    I'm with you, the only time I adjust mine is if I'm cutting a ditch.
  88. Re: Cutter gearbox question for seasoned farmers, machinists and engineers

    Try re shimming and get about .025 backlash, then should run cooler and with less noise.
  89. Replies
    3
    Views
    754

    Tiller Re: Tiller for Kubota L3410

    Me too. I use the 72" KK on a B7800.
  90. Re: Ford 4000 1972 height of 3 point hydraulic

    The feedback adjustment is not set right. Check your manual and it tells how to set it.
  91. Replies
    1
    Views
    891

    Re: Massey 188 Lwr Lift Arms Worn

    Weld on work good. Where is cork?
  92. Replies
    13
    Views
    1,439

    Re: B7800 over heating?

    Best way to check water pump is to check and see if water is dripping on the bottom side. Then remove belt and check for movement in the shaft. That is after you checked belt and cleaned the...
  93. Re: Must click return 2 or 3 times to get to the previous page.

    Try right clicking the back arrow and see if you see google double click. I always right click the back arrow and go to where I was.
  94. Replies
    24
    Views
    2,233

    Mowing Re: Mowing with FEL

    I take the loader off, it's in the way and I don't like the ride. If I was bush hoging a new place I would maybe leave it on.
  95. Replies
    6
    Views
    1,475

    Re: Hydraulic oil for Farmall Super C

    I only lived 3 blocks from the Loves Park plant{Hollis ave.} and I also worked there in the paint booth for a short time, maybe 1 1/2 years and that would of been about the time you started there. I...
  96. Re: Please help identify inflow and outflow ports for remote install

    No valve down stream from the T well work.
  97. Replies
    9
    Views
    1,490

    Re: BX2230 hydraulics question

    Go here they have the parts manual, but no owner manual. For now I would load what they have for the owners manual, the BX's are all about the same when it comes to filters and est.

    Kubotabooks.com
  98. Price Check Re: Is this Tractor worth anything? (MF 210) ?

    Check the tractor junk yards and also look at this. TractorData.com Massey Ferguson 21 tractor information
  99. Re: Add remote on Ford 3000 for batwing finish mower

    Well that's good. Didn't know that for sure.
  100. Re: Add remote on Ford 3000 for batwing finish mower

    Don't you need a sub plate under the valve? I am not sure but was thinking the fords did.
Results 1 to 100 of 3300
Page 1 of 33 1 2 3 4
© 2017 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.