Search:

Type: Posts; User: SSdoxie; Keyword(s):

Results 1 to 100 of 2472
Page 1 of 25 1 2 3 4

Search: Search took 0.09 seconds.

  1. Replies
    4
    Views
    512

    Re: CT 335 HST Tranny problem

    Follow the shift linkage rod from lever back to where it connects to case. There is a bell crank that goes over the shaft going into the transmission. This bell crank is fastened to the shaft with...
  2. Front-End Loader Re: Help with loader mount for Bobcat CT450 please!

    509971

    The attached is parts illustration for that 9TL loader. Note: item #12 bushing requires qty 8, means these are used on the front 4 bolts of each bracket. Looks like they used a bushing...
  3. Thread: TRACTION LOCK

    by SSdoxie
    Replies
    3
    Views
    3,627

    Re: TRACTION LOCK

    The solenoid has 3 wires on it. 1 is ground, 1 is high amp 12v momentary pull to pull the stem up, and the other is low amp 12v to hold the solenoid in unlock position. The Pull circuit which has...
  4. Replies
    1
    Views
    315

    Re: Bobcat 753 Pedals Stuck

    Bobcat uses a pedal locking system integrated into the seat bar to lock pedals in neutral (center) position when seat bar is raised to help prevent loader movement if pedal is stepped while exiting...
  5. Re: Turn signal woes (or how not to get hit by traffic)

    X2 and wire them to a separate circuit so they don't flash with the 4 way.
  6. Replies
    15
    Views
    1,108

    Comparison Re: HST vs. Shuttle

    To get a more true idea of power loss through HST compare PTO HP of both gear and like model HST. That difference in lower HST pto HP is what the charge pump/replenishing circuit is using from the...
  7. Replies
    12
    Views
    2,401

    Re: CT445 high pitch whine in reverse

    I don't know if the updated relief valve will fit in older pump, or if the charge relief can be replaced without removing and disassembling pump. Won't to ask.
  8. Replies
    12
    Views
    2,401

    Re: CT445 high pitch whine in reverse

    The in field fix was to add a hose to act as an accumulator to absorb the vibration pulses caused by the charge pressure relief chattering. Final production fix was a redesign of the relief valve to...
  9. Replies
    20
    Views
    4,054

    Re: ct235 no glow plugs and no start issue

    Before replacing the control module do a couple more tests. You said when checking glow plug relay with key to ON lost voltage. Test relay in same place but turn and hold key to left...
  10. Replies
    20
    Views
    4,054

    Re: ct235 no glow plugs and no start issue

    Here is the schematic for it. Let us know what you find.

    505096505096
  11. Replies
    20
    Views
    4,054

    Re: ct235 no glow plugs and no start issue

    You did not mention if the Battery light and Oil Pressure lights come on in dash when key is turned on. If they do not come on, turn key to the left and hold (this is manual glow plug and circuit...
  12. Re: T300 Charge Pressure Issue On Right Motor Only

    Right side pump MAY have suffered internal damage due to sudden loss of fluid when the hose blew. Way to check is to remove both high pressure drive hoses to right motor at the pump then use steel...
  13. Replies
    8
    Views
    1,155

    Re: Bobcat 863 will not idle down

    1. Yes. If you disconnect the cable at rear (engine compartment) you should be able to work the throttle by hand. It won't stay where you put it because that is done via a friction washer at the...
  14. Replies
    8
    Views
    1,155

    Re: Bobcat 863 will not idle down

    If the problem is in the governor the timing cover has to be removed. The governor is inside the the cover and will require shop service manual to set it up correctly. The throttle linkage is cable...
  15. Re: Third function dirverter valve vers True 3rd function valve

    The loader valve does have PB already on it. Look at the steel line coming off the inside (left side) of valve running back to the rear. You will see what appears to be an extended female thread...
  16. Loader Re: Kioti CK27 Joystick installed wrong... questions

    I think you will also need to swap the two bucket hoses to keep bucket dump when joystick is moved outward, to right.
  17. Replies
    9
    Views
    1,457

    Re: Bobcat s205 control handles locked

    Glad you got it going.
    Please explain how you found the problem and how you fixed it. This may help others that come here looking for assistance.
  18. Replies
    9
    Views
    1,457

    Re: Bobcat s205 control handles locked

    The door sensor only applies to OEM bobcat door work door that has the Bobcat sensor. That sensor sends a signal to controller to lock the ACS if door is open.
    Stray voltage or short in the front...
  19. Replies
    5
    Views
    3,809

    Re: melroe bobcat 753g "input" error message?

    Low battery voltage can cause the "input" error to display.
  20. Replies
    9
    Views
    1,457

    Re: Bobcat s205 control handles locked

    If you have a cab door, make sure the door is closed fully latched before starting the calibration sequence.
  21. Replies
    9
    Views
    1,457

    Re: Bobcat s205 control handles locked

    Which actuator did you replace lift or tilt?
  22. Replies
    437
    Views
    156,829

    Re: If you have Toolcat questions, ask them here...

    No idea of cost but Bobcat does show a pre-cleaner kit for the F-series in their online catalog. P/N 7270129.

    FYI: I see Bobcat has redone their web page and the online catalog now works Google...
  23. Replies
    54
    Views
    5,129

    Re: auto darkening helmets

    The grind mode is OK but you have to remember to turn it back to weld. I'm a slow learning I guess, it took me 3 repetitions to sink in. The switch on mine is inside the hood which requires taking...
  24. Thread: Bobcat 533

    by SSdoxie
    Replies
    8
    Views
    2,549

    Re: Bobcat 533

    None at all. Never seen a 533 that is why I misread the model number.
  25. Thread: Bobcat 533

    by SSdoxie
    Replies
    8
    Views
    2,549

    Re: Bobcat 533

    Sorry, I was reading this as model 553 not 533.
  26. Thread: Bobcat 533

    by SSdoxie
    Replies
    8
    Views
    2,549

    Re: Bobcat 533

    Be advised if this has an Isuzu engine it has been repowered. Original engine was a Kubota. Might want to check on source/availability of parts for the engine since Bobcat would not have them.
  27. Replies
    13
    Views
    3,084

    Re: Did Bobcat make a gas powered mini backhoe ?

    No it was not Terramite, it was Earthforce made in Chech Republic. Bobcat only had this backhoe line for about 4 years, the purchase was primarily to obtain the manufacturing facility to expand in...
  28. Replies
    2
    Views
    776

    Re: Bobcat 463 cooling system question.

    First - Welcome the TBN.
    The 463 is a skid-steer loader considered construction equipment so this is correct place to post the question.

    From what you are describing - gauge in-op but wires and...
  29. Replies
    13
    Views
    3,084

    Re: Did Bobcat make a gas powered mini backhoe ?

    Bobcat did have a line of smaller tractor backhoes similar to the Termite. The smallest was B200, all were Kubota diesel powered no gas version. If it is one of these the starting issue may be...
  30. Replies
    13
    Views
    3,084

    Re: Did Bobcat make a gas powered mini backhoe ?

    No idea what the first model was, that was long before my time with the company. I do know Bobcat started out in mini-excavator business purchasing machines from Komatsu. At that time the 231 was...
  31. Replies
    13
    Views
    3,084

    Re: Did Bobcat make a gas powered mini backhoe ?

    They never made one that I'm aware of and I retired last year after 18 years with Bobcat.
  32. Replies
    15
    Views
    4,065

    Re: hard starting CT235

    That rough running for a short time when first started with engine cold is normal especially if started before the glow pug light goes out, or if glow plugs are weak/faulty. This tractor has...
  33. Replies
    9
    Views
    6,197

    Re: Bobcat 743B Left Reverse Drive Problem

    It could be something sticky or catching in relief/replenishing check valve but it sounds more like steering linkage is loose. Check all rubber bushings and especially the arm that clamps on to the...
  34. Replies
    16
    Views
    4,778

    Re: CT235 won't start. Fuel solenoid won't engage

    Kioti and Bobcat will be the same parts for the solenoid. Buy them from Kioti
  35. Replies
    11
    Views
    1,282

    Re: What size battery for CK30 HSt?

    I just replaced mine 2 days ago, installed a 24F 700 CCA. The F places the terminals forward of the air filter housing so next time recharging is needed it will be easier access. Any sixe you use...
  36. Backhoe Re: Rear Hydraulics or Power Beyond Tap for Woods Backhoe on CT230

    You have it correct Dave. As an installation precaution, rig up a Tee and pressure gauge so you can check free flowing pressure through the Backhoe valve when the A or B port is activated. Test it...
  37. Backhoe Re: Rear Hydraulics or Power Beyond Tap for Woods Backhoe on CT230

    The relief valve for the hydraulic circuit (loader, rear auxiliary, & 3 point) is at the inlet port of the loader valve. Flow of oil goes from pump to loader to rear aux, to 3 pt. so the loader...
  38. Backhoe Re: Rear Hydraulics or Power Beyond Tap for Woods Backhoe on CT230

    The pressure relief in the loader valve would open in this case to momentarily protect the pump and the engine will RPM will decrease. This would be no different than going to a dirt pile with the...
  39. Backhoe Re: Rear Hydraulics or Power Beyond Tap for Woods Backhoe on CT230

    VONBERG VALVES INLINE CHECK VALVE 19139-.188

    Here is a simple inline check valve for Surplus Center. Shipping will likely be more than the valve @ $8.95.
  40. Replies
    2
    Views
    1,209

    Re: 853 engine knocking ,loud.

    The 853 has an Isuzu 4JB1 engine. This same engine model with different oil pan, intake & exhaust manifolds, and flywheel
    was also used in Mustang skid-loader model 960 & 2060 (2060 is turbo...
  41. Replies
    8
    Views
    11,443

    Re: Trick to unlocking the traction lock?

    This question was posted in 2010 so hopefully he figured it out.
    For anyone coming across this with same issue, check your Park Brake switch. If Park Brake is "ON" or switch is faulty the...
  42. Replies
    2
    Views
    804

    Re: Bobcat 553 magnetic seat switch.

    Bobcat sells a kit to replace the seat switch with a Push to Operate button system so is same as current production loaders. It has a different control box at rear of cab and the Traction Lock...
  43. Thread: new to me 863

    by SSdoxie
    Replies
    3
    Views
    1,403

    Re: new to me 863

    Dealers replace the belt without pulling engine. There are special tools required. Need locator pins to position crank & camshaft at TDC then lock them in place to prevent turning and also requires...
  44. Thread: Fan Belt

    by SSdoxie
    Replies
    5
    Views
    2,254

    Re: Fan Belt

    Check the alternator mounts. Make sure both top and bottom are tight, no cracks in the mount, and the pulley is aligned correctly with the crank and water pump pulleys.
  45. Thread: new to me 863

    by SSdoxie
    Replies
    3
    Views
    1,403

    Re: new to me 863

    The G series is newer version of 863. G series came out in 2000 and was last version made. The electronics are totally different in G to F series.
    I would not use Universal Tractor fluid in it. An...
  46. Re: Bobcat 963 "C Series" Fuel Pickup Tube Location

    Fittings will be somewhere in the front portion of main/primary tank = look in between engine and hydro pump assembly. The 800 series have the belt drive on left hand side so fuel tank fittings are...
  47. Re: Limited slip differential versus Hydrostatic traction control (HTC)

    Mountaineer, Dealer is correct. Any 5610 that has the required cab & mainframe harness, axle shafts to accept the added speed sensor came with HTC as standard equipment, it was/is option for 5600. ...
  48. Replies
    10
    Views
    2,854

    Re: Bobcat 753c overfull chain case

    Thumb switch on right handle is for momentary hydraulics to front couplers is bi-directional. Typically used for cylinder operations. The trigger switch on right handle is for constant flow (detent)...
  49. Replies
    10
    Views
    2,854

    Re: Bobcat 753c overfull chain case

    Look for another one of these for the other motor. Bobcat did change sometimes with different series production, but most 753s had 2 filters - 1 for each motor.
  50. Replies
    10
    Views
    2,854

    Re: Bobcat 753c overfull chain case

    Case drain filter is a small metal canister in-line with the hose. Follow the smaller of 3 hoses going to the drive motor is the case drain, follow that hose back from each motor until you find it. ...
  51. Replies
    10
    Views
    2,854

    Re: Bobcat 753c overfull chain case

    Not necessarily the drive motor seals bad, could be, but fluid is going past the motor carrier seal. The carrier is the assembly that bolts to the chain case frame and has shaft that has splines on...
  52. Replies
    5
    Views
    1,094

    Re: Bobcat 331D no start

    Is there any smoke from exhaust when cranking? If there is smoke, it is getting fuel but firing - 1st thought would be check glow plug/preheat circuit.

    No smoke is no fuel delivery - check fuel...
  53. Replies
    109
    Views
    16,848

    Re: Bad day,Lost an engine

    Load or power to the drive train varies depending on resistance to wheel rotation. At full maximum, stall point, the additional HP combined with slightly higher relief means more torque available to...
  54. Replies
    109
    Views
    16,848

    Re: Bad day,Lost an engine

    Same drivetrain (other than HST in 235) is used on all 3 models. Done for simplicity/commonality of parts for manufacturing.
  55. Replies
    109
    Views
    16,848

    Re: Bad day,Lost an engine

    The 235 engine will fit right in without modifications or other required parts. Part number of the 235 HST is different but that is only because of design of internal directional check valve and...
  56. Replies
    18
    Views
    5,143

    Backhoe Re: Woods subframe to CT230

    The rear mounts of sub-frame will be the same as CK30. The question will be how the front mounts are installed/located. If mounted to the transmission case, flywheel housing, or engine then it...
  57. Replies
    12
    Views
    5,840

    Re: What model of toolcat do I have?

    The front boom design did start with the C-series however Independent Suspension stated with the D-series. With Independent suspension and a Kubota engine it is either a D or F series. First 4...
  58. Thread: Coolant in Oil

    by SSdoxie
    Replies
    20
    Views
    4,186

    Re: Coolant in Oil

    Does this have an engine oil cooler, oil cooled by radiator coolant? If so that would be a place to check. Exchanger rust through and push anti-freeze into oil.
  59. Replies
    6
    Views
    2,035

    Re: 773G turbo B.I.C.S. messing up

    Another possibility I just thought of, although less likely because you say the Traction Lock Override seems to work fine, is loose ground from the controller. Easy enough to check as all the...
  60. Replies
    6
    Views
    2,035

    Re: 773G turbo B.I.C.S. messing up

    For unknown reason the controller is reading the seat bar is being raised/moved out of normal operating position. Three checks to do before at the sensor and/or circuit: 1. Turn key (power up the...
  61. Replies
    22
    Views
    5,883

    Re: Bobcat 753 Arm Lift Problems

    I don't have any good advice on getting this out. The piston does need to be kept square with the barrel as it comes out so it is sliding only on the seal. Coat hanger likely has too much flex to...
  62. Replies
    6
    Views
    2,035

    Re: 773G turbo B.I.C.S. messing up

    With both brakes and loader locking indicates problem in sensor circuit. Could be loose connection in feedback or ground circuits. The seat bar sensor and Press To Operate Button are signal input...
  63. Replies
    6
    Views
    2,035

    Re: 773G turbo B.I.C.S. messing up

    Do the brakes lock up along with the loader control or just loader functions?
  64. Replies
    22
    Views
    5,883

    Re: Bobcat 753 Arm Lift Problems

    Glad you found the lift problem. That rod should be salvageable, clean up end of the threads. I don't see any evidence of Loctite on the rod threads. Red (hi-temp) Loctite is called for in service...
  65. Replies
    22
    Views
    5,883

    Re: Bobcat 753 Arm Lift Problems

    "Tilt and Aux work fine"- indicates supply from pump to control valve is OK. All 3 spools receive flow pump through same line. The load checks I mentioned are internal in the valve, look for 3 hex...
  66. Replies
    25
    Views
    4,725

    Re: Full service - How hard is it to do really?

    No special tricks to this. Remember to drain both oil pan plugs, all 3 hydraulic drains (main plug plus 1 at each axle housing) and do NOT over tighten plugs when reinstalling. Filters aren't too...
  67. Replies
    22
    Views
    5,883

    Re: Bobcat 753 Arm Lift Problems

    I think you may have 2 issues going on, milky fluid and loss of lift. Contaminated/milky fluid should affect all functions not just 1 and I don't see anyway contaminated fluid would allow the lift...
  68. Replies
    74
    Views
    6,120

    Re: How's your hand strength.

    Pair of channel locks and rubber strap wrench for bigger bottles have been normal tools is kitchen drawer for years. Started out Better Half needed them now I do. It couldn't be do to age or...
  69. Replies
    8
    Views
    8,599

    Re: Traction Control

    This is a serial number break in F models, later production can be retrofit with this but earlier production cannot. Kit is not cheap. It requires additional wheel speed sensors, new brake control...
  70. Replies
    22
    Views
    5,883

    Re: Bobcat 753 Arm Lift Problems

    Foamy oil could be water or air. Given the explanation of recent fluid change and leak repairs I think air is more likely. Air entry would be would be somewhere on the non-pressurized side of...
  71. Replies
    22
    Views
    5,883

    Re: Bobcat 753 Arm Lift Problems

    Your description sounds like lift function is going into position when spool is moved even tough lift up control is opposite direction of float. You mentioned actuators so I presume this is either...
  72. Re: question on a frame to bring the rear PTO to the front of tractor?

    I just typed "Rear to Front PTO conversion" in google and came up with this one. Lorenz Front Mount Kits
  73. Replies
    8
    Views
    8,599

    Re: Traction Control

    Traction control is basically same as using independent brakes on a tractor. Difference is there is only 1 brake pedal like in a truck, so using wheel speed sensors the controller notes when a wheel...
  74. Replies
    7
    Views
    2,726

    Re: Where to buy a 7TL FEL?

    The 7TL is only Bobcat model that will fit. The Kioti loader for at CK 30 will fit right up, has same frame. Most all CT230s came with the loader joystick installed so only hydraulic connections...
  75. Replies
    437
    Views
    156,829

    Re: If you have Toolcat questions, ask them here...

    Question should have been posted in Bobcat Construction Equipment Forum not Toolcat. To answer question, yes. If start engine and push the Press to Operate Button with seat bar up the brakes will...
  76. Re: Toolcat series A - please help with fuel line question

    Not sure, but looks like injector should be rotated 180 so return line rubber hose is located at 4 o'clock position.
  77. Replies
    3
    Views
    2,565

    Re: Rerrir Code 50-67

    If it starts to occur more frequently have dealer do a software update. If I remember correctly bobcat released an update to force controller to wait a little longer to verify communication with...
  78. Re: Broke power bobtach hydraulic fitting. Any idea how to replace?

    Could you possibly use something like these Field-Attachable (Reusable) Hose Fittings > Discount Hydraulic Hose.com to cut tee off at main hose install repair fitting, a threaded tee and 2 new hoses...
  79. Re: Broke power bobtach hydraulic fitting. Any idea how to replace?

    Could you possibly use something like these Field-Attachable (Reusable) Hose Fittings > Discount Hydraulic Hose.com to cut tee off at main hose install repair fitting, a threaded tee and 2 new hoses...
  80. Replies
    2
    Views
    1,571

    Re: Fastback 435 drive belt tensioner question

    1. -Take the belt off the tensioner and check tensioner bearing. If bearing is worn out you will run out of adjustment travel. Be sure to adhere to tensioning specs when retightening to prevent...
  81. Replies
    22
    Views
    3,140

    Buying Advice Re: Best way to sell a tractor?

    Offer it as a package but willing to sell implements separate. List price of tractor and each individually with a discount if taking total package. Same strategy dealers use when bundling for a new...
  82. Replies
    9
    Views
    7,906

    Re: CT235 won't turn over

    Lockport; Did you happen to readjust brake pedals recently before this stalling when getting off happened? I ask because mine does this occasionally and started soon after adjusting brakes, I got...
  83. Replies
    62
    Views
    9,091

    Re: Where's the older users

    Got my Medicare card, 1st SS check, and quit work (retired) 3 months ago. Work 2 weeks around home catching up all things I put off due available time while working then when body starts to shut down...
  84. Replies
    2
    Views
    1,781

    Re: 435 ZHS swing problem

    Is there any noise from the motor when it starts slowing down? Noise like metal squeak or screech? This could be motor brake not releasing due to debris lodged in orifice of sequence valve. When...
  85. Re: Noob needs instructions on servicing CK20S HST

    Bobcat filters for a CT120 or CT122 will be same as Kioti CK20. There are 3 drain plugs for the hydraulics 1-center in transmission housing and 2 (1 each) at rear axle housings.
  86. Replies
    7
    Views
    1,124

    Grapple Re: WR Long 3rd function valve issue

    I think SDEF is on the right path. Check the grapple couplers. The loss of operation in 1 direction, tires to move or moves partially then stops is what we see when a loose QD on the loader...
  87. Replies
    6
    Views
    1,051

    Re: Busted my engine

    More than likely you partially sheared the key in the flywheel. Simple fix, remove flywheel and install new woodruff key.
  88. Replies
    41
    Views
    5,341

    Re: How much can a 40hp tractor tow??

    Bobcat's version of that DK40, CT440 list tow capacity of 1433# tongue weight and 7716# total trailer weight. That is without any front ballast so with loader and bucket and using reasonable slow...
  89. Re: Opinions on Kioti's long term stability/viability in the US market?

    FYI; Cruise control will not engage if brake pedals are split, thus reason for the light.
  90. Replies
    1
    Views
    808

    Re: Oil in 1996 Polaris ATV

    Fill the tank full of gas and run it. I usually run 50:1 mixed in my '09 Bobcat/Polaris simply because when I run close to empty the only gas I have close at hand is mixed for chainsaw or boat. ...
  91. Re: Looks like I bent the coupling for the loader

    Yes, engine OFF for all of it.
  92. Re: Looks like I bent the coupling for the loader

    Put the joystick in float position then using a brass pin or wood dowel push in on the female QD poppet to make sure there is no pressure, then look inside the QD to make sure the poppet is setting...
  93. Replies
    14
    Views
    1,794

    Re: Quirky steering on CK2510

    This may be just the style of steering system used. In their previous models CK & DK series Kioti used 2 different systems. The CK 20-35 had "Load Reaction Steering". The when steering wheel was...
  94. Replies
    7
    Views
    1,220

    Re: CK27HSt idle speed.

    Mine idles in the 900 -1000. Same engine as CK27. I usually let it idle closer to 1100 - 1200 just seems to run smoother at that speed.
  95. Replies
    11
    Views
    11,714

    Re: trivial question about the step kit

    Here are the installation instructions for the step. This should have been in the box with the parts or dealer could have printed theses out for you. The holes are drilled through inner wall of cab...
  96. Re: Sizing a hydraulic control valve - size for pump flow, or total flow?

    the 8 GPM would be the better choice.
  97. Re: Sizing a hydraulic control valve - size for pump flow, or total flow?

    Backhoe will get pump flow only. It is difficult to find valves rated less than 10 GPM so 6.7 or 9.9 won't make any noticeable difference.
  98. Replies
    13
    Views
    2,214

    Re: Kioti HST PTO true neutral position?

    The DK uses hydraulic pressure pushing against a clutch pack to engage PTO with spring pushing some pressure on the clutch pack to act as coaster brake. The PTO drive gear is always in contact with...
  99. Replies
    52
    Views
    11,981

    Re: Brush Grapple Preferred Width?

    The bucket that came with the loader is 68" and grapple is 60". When using it for loose brush it will grab enough with branches hanging over the sides to make it interesting weeing where your going...
  100. Replies
    20
    Views
    5,973

    Re: JD Power SSQA upgrade

    My diverter on my hydraulic SSQA has some leakage but any leakage through the diverter is equal to both side of the piston cylinder, base end/extend side has more push force at same pressure than rod...
Results 1 to 100 of 2472
Page 1 of 25 1 2 3 4
© 2017 TractorByNet.com. TractorByNet is a registered trademark of IMC Digital Universe, Inc. Other trademarks on this page are the property of their respective owners.